face off

Пікірлер

@kellyroup4262 2 сағат бұрын

This is pretty awesome!! I'm going to make one! I've built PVC pumps but never tried building a valve or trigger assembly. I think I'll try to design one that fits on a blowgun for varmint hunting. I suppose that done right this would also make a good rat front loading shotgun like a muzzle loader with the proper barrel barrel on it. A great job and nice design! I don't care what the pessimists say about it.

@KyawSoe-kf9gw 5 күн бұрын

👍💓💓💓💗💗💗💗💗💗💗💗💗👍👍👍

@KyawSoe-kf9gw 5 күн бұрын

💓💓💓👍👍

@MoarenbaImchen 5 күн бұрын

Bro can u please make for me I will buy

@KNIGHTSINWHITEFURELISE 7 күн бұрын

GOOD JOB. TOP OF THE RANGE FOR WHAT YOU HAVE MADE. CHEERS.

@KNIGHTSINWHITEFURELISE 7 күн бұрын

GOOD JOB. TOP OF THE RANGE FOR WHAT YOU HAVE MADE. CHEERS.

@ВиталийРадзиховский-з6у 8 күн бұрын

👍👍🤝🤝

@MangtaliPapa 8 күн бұрын

This is not recommend to public

@MangtaliPapa 8 күн бұрын

This is so dangerous you know the pressure of the air 1000 psi enough to explode that pvc it can cous of seriously injury 🤕

@KyawSoe-kf9gw 10 күн бұрын

👍👍👍👍👍👍💗💗💓💓💓💓💓

@brahimirlghost 10 күн бұрын

Bro use strong lighter becase the strong lighter will burn the pipe speed and will shot speed try it❤😊

@zhugekongmin943 11 күн бұрын

被抓了吗？怎么不更新了

@Jandeganjaman 20 күн бұрын

1mm radial wall ? Ok lets see then 😂

@wawanPesona 21 күн бұрын

Two days will spoiled

@haydensuperville1967 24 күн бұрын

Masterful.....

@kurirr896 26 күн бұрын

bisa beli ga bang

@Pedechumbo0 29 күн бұрын

Show

@yvancoissieu7390 Ай бұрын

😊Trés bon travail 👍

@nattapongchoomnikay Ай бұрын

👍

@saadloucif2767 Ай бұрын

تلك القرعة ما في داخلها التي يخرج منها شئ ما،؟؟؟؟؟

@saadloucif2767 Ай бұрын

،🤔🤔🤔🤔🤔🤔🤔 ساعدني في صنع واحدة من هاذه

@Albarwary Ай бұрын

You do not upload the video as you do, you cheat and upload something else when trying it out because you did not complete the gun in the end, and when trying it out we saw it as if it were a completely different gun.

@faceoff2 Ай бұрын

Because of the youtube restrictions, I need to use this way.Nowadays, it's very difficult to upload these kinds of videos, and there is a risk of permanent termination.

@Englishstudent4798 23 күн бұрын

Can you tell me about the trigger built? You did not upload with video, i don't know why but i need it. Can you send me it?@@faceoff2

@JamalbatongJamalbatong77 Ай бұрын

Mantap bosku❤❤❤

@BabulalBadowale Ай бұрын

हेलो गाइस गुड मॉर्निंग यह सामान हम लेना चाहते हैं कहां से मिलेगा गैस का बंदूक बनाने के लिए

@Anurag_04. Ай бұрын

How to make

@pumpsamui3607 Ай бұрын

Thanks so much 😊

@MauricioMurillo-f2p Ай бұрын

How much it cost to make it?

@andywaugh4165 Ай бұрын

Keep the flow bro yr on it!

@vipinkumarjangde6834 Ай бұрын

Kitne me bechega bhai

@futtgaoaze2640 2 ай бұрын

Aveți un dop filetat la exterior pentru o țeavă 1`1/4 ???

@edgardozubiria8664 2 ай бұрын

Genio

@IvanEnao-oz2vd 2 ай бұрын

Y como hizo el gatillo ???????

@BintangSenapan 2 ай бұрын

Mantap bg

@1664smudge 2 ай бұрын

Already done years ago by the legend who is Ben Taylor and far better,along side hugget they produced a pcp that the machining was so good it didn’t even need a seal in the breech hugget is a master at machining metal his moderators are a thing of beauty