Hi, can you update us on the JP performance please...still working, any issues? TIA

2:57 ,,, where is the guide for windows 10 ? , Thanks !

Hey John, it's a nice tutorial and easy to follow. Needless to say I did encounter a few issues. After flashing, the ESP32C3 went straight back into "waiting for download". It was only after I saw you change the memory size from 2M to 4M in the "Serial flasher config" menu that I saw the option "After flashing (rest after flashing)", I noticed yours was also set to this, but I changed mine to "After flashing (stay in bootloader)" And it worked. I noticed that all of my ESP32C3 devices seem to do this, even when using the espressif ESP-launchpad web page. Maybe I have some defective ESP32C3 devices? Strange as they work normally aside from this. When it comes to Rainmaker, do you think that the ESP-IDF is better to use, or do you think that the Arduino-IDE is better ? It certainly seems to be easier with the Arduino-IDE, but the ESP-IDF seems to output a lot more helpful log messages to the console at run time.

How do you get Network ports working in wsl so i can use OTA? Network ports show up in windows but not wsl thanks

How do you like the heater? Still working nicely?

Hi, i need the program, please

Thanks you very much, can you make a video about Rainmaker apps customization?

Thanks for the video. I have an issue when the program is uploaded, the serial prints in loop and i never get the qr, the board is correct , and im uploading the example code from rainmaker : rst:0x3 (SW_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:1448 load:0x40078000,len:14844 ho 0 tail 12 room 4 load:0x40080400,len:4 load:0x40080404,len:3356 entry 0x4008059c ets Jul 29 2019 12:21:46 any solution for this?

Hi John I’m looking at your video and I’m going to go with one too….can you say what the import charges were …or the % of the total you have to pay.

Why does it not support 32bit Windows 7? I don't afford a 64bit PC now. I have Windows 7 PC. It fails the basic creation of interface. Do you have any solution? Please let me know.

Is it possible to use esp32 tasmota in home assistant via mqtt and the remaker at the same time? use both software at the same time.

You are great, Sir!

Hi, great video..im about to start my install..I have a question perhaps you can assist me with? I Spoke to Truma today and the tech guy said …be careful when you fit the exhaust, don’t put any twists or turns in it (it can cause issues) Did you put bends in the exhaust or keep the exhaust pipe straight ? Regards Ray

Very nice, so your having fun with J1939, I had fun with this when trying to write a software specification for a control panel to connect to generators and other systems while all sharing the same CAM bus. what fun it was. if only i had some lovely moving pictures to show my boss, he would have thought I was working very hard. :-) they do like things they can show on a screen. nice to see you posting a new video it's been a while.

Thanks for the video, i was looking for something to connect 8266 to ESP32 and use it via ESP rainmaker. Q: Can we use http instead of mqtt and skip the whole broker part(for something simple like a light switch).?

2:08 Hello, which example do you use?

Sir, can you please esp32 to 74HC595D output shift resistor code? With rainmaker / mtqq / / tomozoto app with alexa google assistant?

Hi great system one thing that I fitted was a pressure gauges so I cud adjust system pressure and not rely on pump switch micro switch

Can i use nodemcu bord for that

I was going to join your channel until I noted that it's all in the cloud, so if the internet goes down then nothing will work, I have tried EweLink and had the same problem everything stopped working so could not turn on or off my lights, I just want to stay local.

Hi John, I managed installing Windows 11 WSL/Ubuntu 22.04 for Arduino new IDE 2.2.1 "arduino-ide_2.2.1_Linux_64bit.AppImage" . Rainmaker compiles now 30s (and more than 2mn on standard Windows 11). I will try on a standalone Ubuntu partition to see if it compiles quicker than hosted on Windows 11. My setup is a decent laptop Acer intel i7 8GB SSD. thanks for your great tutorial Install Ubuntu22.04 on WSL (Windows 11) Start Ubuntu22.04 sudo apt-get update && sudo apt-get upgrade -y sudo apt install nautilus -y (like file explorer in Windows) Reboot windows or Nautilus fails the window display nautilus & // little window opens mkdir Arduino cd Arduino explorer.exe . // copy/paste Arduino file downloaded: Image Linux Arduino "arduino-ide_2.2.1_Linux_64bit.AppImage" in a directory you have created : Arduino/ chmod u+x arduino-ide_2.2.1_Linux_64bit.AppImage sudo apt-get install -y libgbm-dev sudo apt install xterm sudo apt install libfuse2 sudo apt install libasound2 sudo apt-get update && sudo apt-get upgrade -y nautilus Double click on "arduino-ide_2.2.1_Linux_64bit.AppImage" (you have previusly followed USB port procedure).. well well Linux is nice but not really easy..

Great And Awesome video hats off to Bro I just Don't have Any words to exclaim

Thanks for the video. Why do you use VSC only to edit the main source? Isn't it possible to build the project here too? Greetings!

Is there any example that shows how to compile and flash this project with VSC ? Thank you.

Do we know WHY it's any faster?

Hi dear friend While admiring you I have a question I wrote a program in which I want to use the following command to send an important message to the phone esp_err_t esp_rmaker_raise_alert(const char *alart_str) Can you show me its format with an example? Thank you again

Hello Thank you very much for sharing your nice and simple program I managed to change variables such as temperature, humidity and timer time in the program by using your program template and slider definition. Thank you again

what partition did you select? How do you make code updates via OTA?

I apologize for not understanding your solution. How to update the rainmaker code via OTA?

❤_dear sir_ ❤ Shall I use this PWM signal using to start bldc motor control system.... Using this pwm to give input for a driver circuit Is it possible? Sir

Nice gifts, just don't smoke them too soon 🙂

Nice package John! Congrats.

John, thanks for the video. I worked along with the video, and (having never done SMD or similar rework before) gained much confidence from your approach... especially the accidental reversal of the display, which told me that you do have a second chance if you are careful. Good input because my first powerup did not result in a display. Well.. simply resoldered across the display pads and VOILA. TS-100 is back in service.

SIR ....how to fix this error : E (70287) esp_rmaker_node_config: Buffer size 2048 not sufficient for Node Config. E (70287) esp_rmaker_node_config: Could not get node configuration for reporting to cloud E (70291) esp_rmaker_core: Report node config failed. E (70296) esp_rmaker_core: Aborting!!!

I'm trying to make it work with version 2.1.0

The BIG question...WHY? Why is the ide under Windows 10 so slow? It shouldn't be a problem. Nobody seems to have the answer. Post another video when you find out why.

Is the heater still running without problems or were there defective?

How do update 'setTemperature' value on "esp.device.thermostat" device?

what are you doing with the Camb Hams?

So where's the tasting report ?

Something i have been trying to wrap my head around the last few days. is the ability to have dropdowns in RM. Was hoping to add a few FastLED effects in a RM install, so that i could use a Button or touch to switch modes and dimming. I feel like it should be possible. But i Seem to find myself lost looking for examples of anyone having a similar idea 😂

Hello I have a request for you please help me if you can I live in a forest and have my own electricity from solar panels and from a small turbine on the stream I should check the voltage from the turbine on an esp32 pin and if the voltage starts to rise, I should include a strong waiting resistor on a pwm pin to slow down the turbine if the batteries are charging, all this can be seen on the esp rainmaker my level of knowledge is only copy paste unfortunately I thank you in advance for your time and effort

Thank you very much for the tutorial, but I have tried Rainmaker but it works very badly, the calendar does not appear, or it takes a long time to appear, and then it does not work, also the status of the lights, sometimes it shows like it is on and off, or things So, what makes the application unreliable? I'm looking for one that works better

My LCD lost the backlight. I can still read it, but it is very faint.

rainmaker is cloudbased, why would you use it?

Clever. Thank you!

Really good project, please do you know if alexa is still running for rainmaker ? because i having a acessdenied return, thanks

can u do a tutorial on mqtt

Dear Could you make a video using servo motor on esp32 rainmaker no one has done it yet. I count on your tutorials they are incredible excellent Thank you very much

I'm getting Claiming failed with error : Claim init failed error in the app, after scanning the qr code. it never happened before. Someone please help me.