Team Strip'em. Haha

But mines is all oem except the cam gear

I have the same setup but am having some problem with the timing

Very helpful 5 years later‼️ thank you for this ‼️

Is that Alex? lol this is Brodie i was trying to find California legal turbos on KZbin n I clicked on your video not knowing it’s u lol

What distributor did you use? I’m having a problem with the d16z6 head on a d16y7 block nothing seems to work

What water bump did you use for the z6 on y7 block did timing come out right

Would you be able to walk me through to time mine? My neighbor didn’t time it right started a few times now nothing and 1 spark plug it’s like blown. I have the same setup but no turbo

How much power were you getting

My tires are leaning in on my 89 and eating my tires up. Will this shit fix mine. It's lowered on some speeding rods atm.

are those notches not toward the intake?

Did the aem fit right on the stock rail? And how did you run the gauge for fuel pressure

i’m thinking about getting a D16, are these “plug and play” lol, curious because i don’t have any of the tools to machine or whatever you have to do to make these fit like stock! great video btw!

Hopefully stock 75.5mm sleeves can take a lil bit of boost. The standard walls have a score going down I think on cyl #3

Are the pistons forged?

What BOV u running bro?

Would that piece cause shaking?

what crank did you use ? z6 or y7 crank ? I'm guessing y7 right ? I built my head already and I'm going to throw it on my y7 block after i get my piston and rods

"Who knew i could rebuild an engine" . You just motivated me to do mines lol

I just ordered xline rad for ek hatch turbo. Did temp was down from performance one?

big difference?

Can you upload a tuttorial on backfire launch control srttings using this neptune

Sounds not healthy

Hey bro I'm doing a z6 head on y7 rn. Did you have timing issues? I bought an adjustable gear incase but man trying to find info on this is hard. Any info is super appreciated.

Great video, thanks!

Just bought the same upper control arms for my integra and (1) came also flat, thank you for the tip man it was very helpful. I figured you just had to put a little elbow grease in it but didnt want to screw anything up ive waited a week for these things to arrive lol.

I’m learning as I go ….. I’ve watch like 6diff traction bar vids Why do all these makers not weld on tabs to keep that front motor mount??

Except fke the FACT,you put used parts on it lol..as watching,i was thinking DAAAYYUUMM ol boy went all out on that parts list,he spared no $ thats for sure. And than you said you put a new waterpump on,as i looked i seen calcium deposits on the tube.hint it is a USED pump in which was run with purely water. Idk bro all i know,is you made an awesome video,but an even cooler car

Lol

What are the torque pecs?

Q buen troncho de Mari jejejeje

Looks good. How's the car holding up?

The jack under the spindle is right . Should have removed the other jack. Then put a digital level on the trunk and jack the spendel until the car is level. Then adjust camber. I did it and mine are 0.. and if you don't level the rear of the car side to side with one wheel on. And if you just jack the car up to an unknown hight and set camber it won't be right when your done. Then put the digital level on the break rotor cause that's flat. And adjust..

You should use channel locks, I don’t have channel locks so I’ll use these. while you have channel locks in your hand. Lol. Appreciate the video tho. Thanks

Why is my z6 I have a problem on the top right to it’s higher then others is that normal

would it be good to put anti seize on the components?

How do you like skunk2 valvetrain

ayyy nice, just upgraded my shifter to the skunk2 short shifter. Now i want to do the lower control arm so glad theres a vid for skunk2. Ill put on my channel.

D16z6?

Did you notice or measure what the max positive or negative camber would be if adjusted either way ? And I see this video is a little older, hoe ate they holding up ?

Does a camber kit reduce the chances of replacing tyres frequently

So i have a b16 stock rail i know the inlet comes out but can't seem to undo it anyone know the bolt size/thread pitch so i can double nut wrench it out

Where you get that cutting tool from

Can a D16A6 Engine to any D16 Engine? If so what do it need to be done harness? Transmission? ECU?

so i didn't hand tight the inner 2 bolts, and now they are all stripped. someone help please

Just got a y8 block will s d16a6 timing work ?

Ca tint law 5% rear and 35% for front

do they make the no notch in a regular 137mm spec? i'm using P29 pistons so i'm genuinely curious.

How do you delete de canister line that goes to the tank? Do you have you block off a line coming from the tank?

New subscribe 🛎🔔💯