really cool to see what the next generation of custom builds will be.

Is this still available?

Biggest problem finding a s550 mustang rear independent suspension prices gone through the foof

Can I just cut the frame and try to find a short bed to go with it? Or thos it make any difference???

How does this do on the highway? Im curious if it's over sensitive as it doesn't have a VSS over the can system to reduce feedback.

Bump for update

I've done this twice now in toyota minitrucks. The lateral grip is insane. Great irs to swap.

Any recommendations on where to get a new shifter / dash board for a Modermo?

My Dad had a truck like that.Even as a kit I remember the single wall top half...design. pretty cool.

Lowering it and adding horrible rims definitely lowers you value.

Watched again thks again for the video😁👍

Thank you for the video could you tell size of rear rim and back spacing please

Odd question but I assume a 130 amp single wire alternator is a large enough to support the electric rack on a F100 conversion?

Where can I get the templates boxing plates

you are a lifesaver. The kids like to slam the shifter and it eventually got worn out and only worked in D1 (no reverse or D2). Your video explaining the wires and what they did was super valuable! i was able to just wire it to D2 all the time so they can just go, no matter what position its in. Thanks!!!

I always dreamed of this panel, when I bought it I had the feeling that it would have raised the level of my project, but as I was installing it I realized that I couldn't install the panel reading for my RPM. And I've already contacted you a few times via messages on the website, we've sent emails and so far we've had no success. I decided to send it here to see if exposing the situation could help us.

on what kind of swap can you install this cluster

Who makes these batteries? I want to put a lucid moto in a swap but I know lucid batteries are super expensive and crazy cooling system and stuff

Bumpsides and 73-77 Dentsides are goated.

Great vid she is coming along good ..i havnt seen your other vids yet but when you have the drink in your hand you reminded me of that one guy from trailer park boys😛 ok im off to see the other vids have a good one 🍻 🖖

Could I install this in a 2gen lighting?

Great video Andrew. Got the templates installed & frame cut. Only thing I don't see is where you referenced from to square it up. I used woodworking center points and holes in the frame to get an idea of how close it is.

Hey bud. Found you while searching for the steering being "locked". It won't turn by the wheel, nor the remote. I have pressed the 'lock' button on remote to no relief. Any suggestions? Thanks.

Lame af

Lost me at the Tesla BS.

Like my 4x4 long bed rides snoother

Are You guys taking customers i whant to do a c10 square body?

Would this fit on an 03 mustang?

perhaps i missed it, but why coils and not leaf springs as the manufacturer intended? Don't get me wrong i'm not a purist, but would the leaf springs not handle the weight if it handles a pickup under normal work conditions? I'm currently working on the same project and would love any info you could share!

Need a new remote and they’re literally nowhere. Help!

What is the part number?

PSALM 131 kzbin.info/www/bejne/r17OiKxqqaxke8ksi=n77h10IeqCk9yv4B

1ST CORINTHIANS 13:13 kzbin.info/www/bejne/r17OiKxqqaxke8ksi=n77h10IeqCk9yv4B

How much for one that will fit a 72 f 100

Cordless grinder or sabre saw simple if you put timber wedges in to splay apart cut as you go,only half a mil,cordless grinder switches off when it jams

Brush less cordless death wheel much safer mate ,they just stop

I'm looking for a digital cluster for a 1979 Cadillac coupe can you point me in to the right direction

I find you guys love them scrapping the frame while you drive. Personally, I’d never notch into the frame I’d like it higher

What did you guys do to hot up the rack? The Volvo hydro pumps use one of the small connector wires to hot to turn it on. I can’t see the wiring on the truck without the motor. EDIT:duh I should have finished watching… Thank you for clearing that bit of info up! Looking forward to getting the rack in the truck (1999 f150 swap!) Separate question: Did you use AN lines beforehand on the hydro rack? Which brand fittings/hose did you use on the pressure side?

Why does everyone leave 8" of bandsaw blade showing to cut 1/4" plate? Easier to loose your arm i guess.

Thought it was a great idea and a great build until they started to make it electric.😢

very very interesting. i have an 08 crown vic p71. this is looking like a very possible swap for me. one issue is the drive belt. not sure on how it would be shortened or? if you can get back to us thatd be awesome!

Updates?

I’m pretty sure this car has 775 motors. If so all you have to do is retain the 12 v system on the factory battery and where the power goes to the motors out the controller and a 12v coiled relay and add a 18-24 volt battery feeding in the relay and to the motors. Done. It will retain all lights radio steering control and safety switch.

Bumping for an update!

Awesome upgrade. I tried upgrading to 18v but didn't realize the issues I would face. Would you happen to know why pressing the power button would flash lights and turn off? Please help 🙏 - 12v battery still good - Power button working

Guys! Where is the next episode?

lmao it doesn't even fit between the frame rails, maybe a bit more tinkering in CAD with some simple measurements before buying a whole extra subframe you can't use? Also since you're putting the motor & inverter in front of the diff instead of behind, are you going to mount the Tesla motor upside down and relocate the oil pickup or run it in reverse and swap out the oil pump for an inverse one that pumps the other way?

The amount of cope is strong in these comments.

Why not use a Ford Electric motor? Just a question not knocking the Tesla!