pad slaps are for hacks. do the job right, brakes are too important to be cheap and not put new rotors on.

Great video, thank you

Literally changing mine right now! Literally saved me a lot of money on labor! Thanks for video

Belt was hard to get on because it wasn't on the pulley 😭, rookie

Excellent video. Thanks!

Very helpful

Excelente explicación muchas gracias

Thank you. This was super helpful and I was able to fix this problem in minutes and at very little cost (ordered part on Amazon). 🎉

Best job yet of showing housing clips holding bulb. Thank you!!!

What if you use aftermarket cabin filter that doesn’t have arrows just the part number

Awesome video

I have a 2020 M4 Competition, I plan on changing the oil at 5k intervals between the factory paid 10k intervals. Thank you! What a giant PITA! Could be worse, you need to remove and replace 32 fasteners, 3 different sizes to change the oil in my Lotus Emira. 😂😂

Thanks for help

Would bad sensor tweak the steering wheel so it’s not centered?

Quick question I replaced my UCA LCA inner/outer ties rod my steering wheel might of moved In The process after I was done I test drove and stabilitrak light came on and I took it to alignment and they said they can get wheel straight

I have yet to find the answer BUT ... is the timing chain tensioner easy to replace? Mine chain sounds like it has play and removing this cover reveals the chain tensioner inside but not sure if it's easy to replace. Any ideas guys?

You never say let go of the brake after disengaging the emergency brake than turning it back on. My car starts if I don't let go of the brake. You than say wait 3 seconds than hit the brake. Smh

I took my car to the dealership and had it done for a few grand. Plus had the timing chain replaced. Meanwhile i was tearing up the streets in a 2024 328i in sport mode all day long for free . I didn't even ask for a loaner car the service guy asked me to sign a few papers for insurance and then gave me the keys!

what happens if remove valvetronic motor without turning the screw ? & whats the torque specs on them? bmw 328i x drive 2010 e90

That's it? This is what honda is telling me will cost $1k?

Thanks❤

Toyota did not design this properly as these springs all have a propensity to fall off. Toyota seems to have a particularly challenged fuel filler door group, with flimsy designs like this so prone to failure on all their RAV4s.

I Heard from somebody that when installing a new battery in a Modern 5th gen Rav4 you need a scan tool to register the new battery into your cars computer or it may overcharge your new battery thinking that it is the old one that was going bad.

Your video just saved my day. Thank you❤

This is leaking on my 2019 bmw x3 at 75k miles. I’ve already replaced turbo coolant return line and water pump in the past 10k miles and now this. When I do decide to do it I will be removing the intake and replacing the plastic flange that connects to the block and also replace the oil filter housing to aluminum one. I personally would rather remove the intake then de with the dme and all those wires, that seems like a nightmare and probably hardest part of this job. I love my bmw but it’s one coolant leak after another.

Leave it to BMW to have function following form. Same for Range Rover and Land Rover. Then they try to claim right-to-repair law so they can charge you whatever amount they want. God bless KZbin and this tutorial.

I can’t reset oil service

Whats an "E" brake?. Its a purely mechanically operated handbrake. Its also not "Emery cloth". Its a scouring pad. Emery cloth is heavy duty sandpaper. I would use wire wool and brake cleaner to clean the pins. I would also use a brush to clean the inside of the calipers and cylinders not a rag. I would also clean the wheel inside and out before fitting it. The drivers side disc looks quite scored so I would have replaced the discs too as well as the pins and clip. A very thorough and carefully executed job though and very clear images too 👍

Really great video you have shared. Just perfect all around. Doing my plugs and coils this Sunday. Thank you!

hey thank you man . This helped me replac it on my own.

Thanks for sharing it did save me a lot. doing this on a Honda Crv 2019 with the same engine. Man I did struggle. The engine bay layout is different so I had a difficult time removing the valve cover it was tight the harness that had the coils I could not twist all the way or tuck away I had additional wires needed to remove which I did not because they were linked to the alternator. So that was one thing and another I broke a bolt inside when tighting "Screwed up big time" I didn't have a torque wrench so in the end I managed to take the bolt out and also Find a replacement ( was not easy ) I did end up with micro scratches on the head. Dots scratches I don't know if that's going cause me problems in the long run but their so tiny that I did not bother to layer it with RT. I also used a small wrench to torque the bolts I did not have a torque wrench. It was a challenge. especially when it's not the same car and you don't have the right tools for the Job. I wanted to ask do these engines require valve adjustment?

Are you based in California

Really good video for a total rookie. I especially liked the part at the end about what happens if it doesn't work right away. I thought I had screwed something up, but did what you said and now it works great. Thanks

Actually, I have done exactly the same on my F07. However, when I installed everything and start my engine, There is no air get in the Car. But for sure that the fan is work fine. Do you have any idea why it’s happened. Do I need to reset the computer?

Fantastic video! Great detail discussed here. Thanks for your time and efforts

❤❤

Thanks man. Your video makes my brakes replacement whole a lot easier!! 🤝

I love you bro

wht if you snap a bit of your tensioner when trying to lift?

ABSOLUTELY NO REASON TO TAKE OFF THE CLAMP.

Great Video, Ill be doing this job next week. Will probably watch this vid a few more times beforehand.

Wondering why you spun the new filter to the left where the Honda logo was hidden, rather than straight in where the logo would be at the front.. which is where it was on the one that was being replaced? hmmm...

I don't know why my 14mm socket does not work when i tried to unscrew the spark plug. It feels like there is no spark plug inside the cylinder, as i can't feel any force when i move the ratchet counterclockwise

So stupid just 3 skrews.

STOP. Do not follow these instructions unless you want a new rattle as you're driving down the road. The Ford Explorer has two white pins holding the far left and right ends of the glove box firmly. You must reach under the glove box, find the white tabs on the pins and push the left one to the right and the right one to the left until they clear. I don't think you have to completely remove them, simply move them until they no longer impede removal of the glove box. Clearly, both pins were broken off and removed from this vehicle, which may cause the glove box to rattle when driving.

Too many extra unecessary steps here, literally taking half the engine apart😂

Very good video

My ignition coil won’t seat all the way , can anyone help with this issue? I’ve changed all the coils and they’re all the same but for some reason one just won’t go all the way in

Might clean and add some high tem. Grease to the pins, great video!

Great instructor, clear and extremely helpful. FYI. BMW of San Diego wanted $350 to replace this ONE filter as shown in this video. This is outrageous and this is why, in part, Friendly Mechanic's channel is such a great public service.