Good work

My 2004 tahoe is not coming up to operating temperature, after replacing a leaking radiator.... fluid levels normal. Drove it for 3 months, then changed Thermostat , still not coming up to temp very low... antifreeze correct level .... I have a constant flow of antifreeze going into Reservoir even when first started cold... I would have swear the Thermostat is bad but, the Thermostat is good.

My 2000 Suburban has rear heat so it has a tee to that right behind the (broken) quick disconnect fitting on the heater hose at the firewall. So there is little clearance for the ring-like tool to placed over the fixed line and pressed into the fitting to remove it. I cut one of the plastic-type ring tools (from O'Reilly) down to about 2/3 of a ring so it would still catch the opposing tabs but have a clear space to straddle the tee line, and I finally got it to work. This video and another gave me the information needed to accomplish the repair, and I have heat once again in my truck for winter. Thanks!

This does not help me. Mine is stone cold no matter how far I drive.

HECK yes this was exactly what I needed! Thanks!!!

Thanks brother just turned truck off in revese and i wasnt sure how to get it towed thanks a bunch

How to get ot out of neutral?????

My issue was, even though coolant level was good engine temp was fine, but transmission was running a little warmer than usual. It was low coolant. Ran a hose into the coolant tank and with the motor off kept squeezing the top hose. When I did it for 5 minutes or so,it got hot again

The only guy that knows all the part names that I've been trying to figure out for months now lol.

Thanks so much

thank you great video

RIP Condolences to the family.

What material is the coupler made of?

neutral on the transfercase not the same?

I have a 2006 ford and it starts goes into all gears but dies nit move. I noticed that it was hard to get it out of park a few backs back. Now the issue is that it will jit move in D 9r 1 or 2nd or reverse . Yes lots of water spilled in cup holder

What are the consequences of ignoring these EVAP codes?

thank you so much for your video. I'm getting a dodge ram into neutral when there's no power. I'm certain of the gas station is grateful as I was blocking all of their pumps and couldn't move the vehicle. Your video allowed me to quickly quickly disengage the pin and push the truck out out of the way. Thank you very much for your online help.

Thanks! I removed my cartridge holder or whatever it's called yesterday and ran warm over it until the water ran clear which took forever, allowed to air dry but still no black ink. Watching your video today I noticed you used a built-in cartridge cleaner so I tried that and it worked. 😊

04 silverado, 5.3 no heat issiue,head dash unit is new about 1 month old,new water pump no leaks under hood. Bottom 3 buttons on head unit isnt lighting up now( air circulation, ac,and rear defrost ) blower motor only kicks on woth speed 4 and 5. Not sure where the problem is at?

No one pulls that out without tear down, needle nose, yeah, I have so many Ford certs from when they started sending us to Ford, in 1994 to 2012 on the wall you can't see the wall and own a 2010 explorer Eddie Bauer. I love how none of it was filmed, you have to take console out or you will destroy wires and then start soldering new wires. ITS still easy but not video editing easy..

Thanks. Doing an alignment also

Thank-you Sir. 👍

I'm having this issue with my 2008 explorer

@tmargal2271 0 seconds ago Good day Mr. Doctor D have a 2012 Dodge Durango brother change the blend door actuators but still no cold air. Any ideas what to do next to make it work. Thanks

Great job 👍

HUGELY HELPFUL!! Thank you!

I have a 99 Chef suburban with a 5.7 L and have had changed my injectors twice already. After the third time now I’m getting the same symptoms where fuel is leaking into my oil crank case any idea why or how? Any information is greatly appreciated

We don't want to see your face, show the truck please.

I cranked down to hard on my oil filter and she busted!

Well, there went 50 bucks

Thank you! 🙂

Wow! I grew up on setnet sites near Clam Gulch at Falls Creek! We fished there from 1948 to 1959 back in the territorial days when there were still fish traps. I hung a lot of gear as a kid, but never used a bench.

P0440 code. Could lead to vehicle operations to run lean.. And cause knock or ping issue and burn spark plug. Just check #1 plug. If it's hot white.its definitely lean. It'll burn the plugs up. Evap purge ? I'll check that.

Helped out a ton. Appreciated

My 2002 chevy just broke the nip off. Thanks for the video!!

I have a 1999 Ford f150 5.4 V8 Lariat 4x4 and it doesn't have a sway bar and the key I had came with two or links so I'm hoping after watching the video I'll be able to figure out where I need to install a sway bar on this truck but does anybody have an idea why somebody would take the sway bar off? They install the pre-simple steering stabilizer on it ( The owner before me ) but on the Ford form site if I people telling me that he was a dumbass high school kid who wanted to make a little 4x4 truck super awesome which I don't know the guy and I can't get hold of her now figure out why there's no sway bar

How about recalibrating the heater controls? Does that fix anything?

Mine will AirPrint from my iPad but won’t print on machine when I place a paper on the top and press print. I will try cleaning it.

Push "what" what way?????? Didn't show that too clear.

But great video anyway. Thx!

This man does not blink.

Will this work for the 2004 Eddie b edit?

We see a lot of this in Kodiak as well. I've recommended that anytime you are pouring fuel from a portable container into something else - even a lawnmower, that you use one of those "Mr. Funnel" or Raycor funnels. Those funnels are worth their weight in gold!

Wow, Will that mess up the engine of that truck? Great video & job thumbs up. Stay well & safe Tim.

Thank you for that video it was very helpful

My son and I just had to do that putting his truck in Neutral to tow it to the shop but when we started down the driveway the back right tire wouldn't spin can you help please 2:28

Trans is still engaged burned up a trans getting towed a few miles doing this

Super helpful for me this morning! Thanks!

Where is the bcm?

I love it! I was a bit worried about the setup because I read mixed reviews, but the setup was so easy kzbin.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 , I literally set it up in under 5 minutes. The print quality is amazing and it comes with 6 months free of instant ink which is definitely a plus! This is an amazing all-in-one printer for pretty cheap, I 100% recommend this and would definitely buy again.