Great answer to my known worry. My gear was stripped so bad the motor ran but the trolly stayed still. The motor would stop going one way but keep running the other. It makes sense to center everything. I am wondering how these plastic rods do what they do?

Still can’t get this thing to work 🤦‍♂️

In this video I understand more balancíng Mike

Hey, Your video was so helpful! I couldn't get it to connect. I wasn't engaging it properly! Thank you so much! 😃

Great video. Other people were saying push forward with the rope. You nailed it by saying to push towards the door. That was the one that did it. Thank you. A beer on me.

Thank you Huge hlep

Mike, how are you? What happens if I have 2 springs, 1 P728 and 1 P528 on each side? Is it supposed to hold approximately 120 kilos and I only have 100 of the gate? Nothing? Or yes? Thanks. One of the anchors on one arm broke, but I think the material was just a plaster cover or something. Thanks, I'm sad. If you attach it to a wooden gate and nothing happens, I attach it to cement or cement finish and it cracks. It's a pity I don't have your email to send you photos. Happy Sunday.

Thank you! Worked like a charm

Thank you!

Thank you

I'm just finding this video and I hope it works for mine because I had to undo it because of Hurricane Helene and I can't get the thing to reengage electrically...

This was amazing Mike! You covered everything! As a general I've installed a couple sectionals and even a couple roll ups and a few tilts. These tilt-ups garage doors are what I grew up with and I wish I knew what you know when I was installing them. you are a pro dude!!!

Thank you! You helped after Milton in Florida! I was able to do it myself!

Thanks! 👍

Thanks for this wonderful video. Very clear and it got my garage operating again!

The problem is that the chain catch is no longer alligned with the release mechanism. You have to manually close the door again to align the mechanism THEN snap the lever back in-place.

Perfect. After the recent hurricane, was able to easily disconnect, but could not remember how to reconnect. Thanks!

Thank you I definitely needed this, getting ready for Hurricane Milton in Ocala!

Mine was similar I just had to pull it back like you showed at the end! Thanks!

I have spent 3 days to adjust without knowledge untill I see this video, help me fix within 1hour, God bless you

Thank you so much!! The only thing I didn't do to reingage was having the garage door halfway down. I am a solo gal taking care of my Father who has Dementia. Just went through hurricane Helene. Finally got power restoration after 7 nights and 6 days without power and could not figure this out. Again, I THANK YOU!!

Thank you! Of course the owners manual did not say how to reconnect the door.

Beautiful video, quick and to the point. You’re a hero!

Thank you for the spring explanation. I was stumped for a bit.

Thank you for sharing the video. It helped me out

Thank you so much!!! 🎉

Outstanding video with great details on how E-900 functions

I push the button and get an electric hum like everything is frozen. Any ideas?

This info for me is a huge win! Thanks for your help sir.

mike good morning, why does the right support (starting at minute 25) have a long screw with a nut sticking out all the way up in the middle that the left support with the manufacturer's decal doesn't have? there's only one hole in the same position. what is it for? is it a stopper? because it gets in the way a bit when moving the arm if it's not properly aligned, since the nut is positioned towards the movement of the arm. thanks. greetings. have a great week.

How much of a gap do you leave at the top of the door to allow it to tilt open? Also how big is that door?

IDK what "springy" means. I dont know what going up one on the chain means. Is that adding or subtracting a link?

Thank you sir

Thank you.

This is exactly what I needed and couldn’t find anywhere else. Thank you! Subscribed and liked.

not even same brand or model but you showed me what i needed - thank you!! 😎😎😎😎😎😎

Thanks so much. I couldn’t get mine to reset, but I wasn’t pulling the cord hard enough for it to click over.

great help! super simple

Thank you for the information. I have issue with my garage door today, barely going down and have to hold the button to close it shut all the way. I will try and troubleshoot later today when i get home and will apply your tips. 😊😊

I can’t thank you enough 🙄

Thank you Sir !!!

I feel so accomplished!!! Got my door back on track. Thank you so much for this. KZbin rocks!!🌺❤🌺

Thanks. Saved me bunch of money. Thought I had to call a tech!

Thank you! Had no idea what to do. Was about to call a door company then I saw your video.

Hello sir, great video! A few quick questions: I have this exact opener. It still works fine with the push button and my car's built-in garage opener buttons, but it stopped working with the remote. I changed the remote battery to no avail and made sure the pins were in the correct positions. I ordered a couple new remotes that looked the same, but they didn't work. Is the original receiver a Linear Delta 3? Do you think the receiver needs to be replaced? If so, how do I do that? Can I do so without having to disassemble the whole thing? Thanks!

Well this saved my butt. I thought I would have to call someone until I seen this video. Sure enough the door just needed to be connected back to the trolley. Thank you sir!

Man I wish you were in Oakland!!!

Hey got a problem with my door can’t adjust it to open high enough when I do just it high it hits the bottom and won’t close three attempts and nothing???? Don’t know what I’m doing in Oakland.

This saved my marriage just now. Mama MacGyver would be nowhere without KZbin!

Hey there, I have the same genie blue max and I’m having problems with it not wanting to close. It open fine without any problem but it doesn’t close. I checked the sensors and they are fine. Can you please help