Thanks a lotttt sir, can you help me how to add a fence connected to the ground grid into the etap simulation, then how to run it

Sir Please share some oti files for analysis

Transient reactance comes in picture during motor starting .

do you know where I can get a list of LV molded-case circuit breakers library list supported in each Etap Version please?

Can you share this excell file? Thanks for the explanation.

hi, can u share on how u differentiate between 4000K & 6500K CCT

Great

What is a tmsh?

Is it ok if we use Delta / Delta transformer on the MV side?

Sir explane videos in hindi ...

WHAT ABOUT THE GROUNDING CONFIGURATION FOR BOTH THE TRAFOS ( THE NEUTRAL POINT SAME OR DIFFERENT NEUTRAL GROUNDING POINT )

Could you give me that Excel file???

How to check neutral voltage?

Thank you so much, easy for understanding _/i\_

WHY THE NEGATIVE TAPPING INCREASE THE V, WHILE IN REALITY IT IS THE POSITIVE TAPPING IS THE ONLY WAY TO INCREASE THE SECONDARY VOLTAGE???

sir kindly share the spread already sent request on mail

Do you know if it is possible and how to filter results before exporting to excel? for example by zone or area. If it is in another of your videos i'd love if you point it out!

video is still, re-record this video

Please re-record this video due to background humming noise throughout the entire video

Dear Sir, highly professional and practical, great approach.

How to do simulation for fully maximized lump load? Which parameters should I change?

@SmartEducare Have you tried to calculate the single-phase fault current for the Y/Yn connected transformer? Despite the secondary winding neutral being grounded, Etap shows that the fault current is zero, and un-faulted phases' voltages are equal to the line voltage - the same as for isolated neutral or delta-winding transformer with a 1-phase fault.

how to find value kAsc & X/R in power grid?.

please share the excel sheet

can you please share the excel sheet?

i love your content broo keep up the good work

THANKS! GREETINGS FROM BRAZIL

plz share excell file

Hello Engineer, could you please tell me where I can find the complementary video following the one above?

Dyn1 transformer cannot be paralleled with Dyn11 transformer. In reality, there will be a phase difference of 10Deg between the voltage of both transformer and this can lead to hug circulating currents if paralleled. ETAP does not give an error or warning for when two transformers with different vector groups are paralleled.

Hello where did you downloaded the catalog for Philips? Thank you

Thank you very much! It is a very useful video! May I know if the setting in actual case is 4 x 300 / 5A PCT 10P10, what will be the settings in Phase, Neutral, Ground and Sen. Ground in ETAP?

In case of MV/MV Transformers if there are no MV motors/loads, can we use Delta/Delta Transformers . any disadvantages / advantages?

Sir sorry, I have question in cable sizing. What is the meaning of no of runs? Example: 5R/3.5C/240sqm/XLPE and 1R/3.5C/25sqm/XLPE Thank you Sir

Irrespective of vector group, load sharing is not showing circulating currents in Etap for vector groups which are not to be operated in parallel. Why? I have tried many transformers with unmacthed vector groups in parallel but in none group etap shows circulating current. Etap simulate normal load sharing for such parallel operation.

How did you choose the pick up current 1.05 ? As I know, it suppose to be the normal load current * 1.20 , which is huge. Thanks

Email id pls

You are Gem

How can we get excel

is their anyone who can help me out for the installation of etap

sir can you please post the link of the video where you have detailed the concept of trip device in low voltage circuit breaker?

Sir, i sent mail query. Please reply

This channel is very extraordinary in explaining, good content also for someone who is still a beginner. he kindly also shared the entire file on this video. hopefully fast growing and successful your youtube channel. PLZ make more useful video and manual calculation (ETAP) SOFTWARE THANKS

Is there any way to simulate Transient voltage recovery after Generator fault clearance?

Lighting loads or sockets which may or may not be connected to motor shall be considered as static load?

very nice explained with perfect calculation plz make more etap videos with your projects and also share all excel sheets

Hi , what about the min. gap conductors/phases. And min gap conductors (L-G). Please clarify how we can get the above info

Kind of pointless video. Why not explain the reasons for selecting the values you did ? You didn’t explain the pickup range values, curve type, or how to coordinate with existing data.

Your english is so frightened that I can hear nothing。。。。。。。。。。。