Hello Time 11:35 ,How did you do it ? ( merge face reinforced pad + nozzle surface ) ? Thanks !

while doing thermal simulation what should be used FEA or CFD ?

The video is not clear

thanks

Can you send the project wbpz file

Sir, How can you decide to split your lug hole face. Is there any rule? For example, Lug hole diameter is 61mm and shackle pin diameter is 57mm and also there is 45° lifting angle. How many portions should we divide the inner surface of the lug into and how many contact portions should we define? And also surface area of selected lug hole at 60° and at 90° lifting operation is different.

Very informative but you are too fast in your explanations.

Thanks a lot

Thank you, very nice video. I have doubts - how can I change the joint to the article and another fixed. For example, the brace with beams will be articulate. It can be necessary to fix a column with a beam. could you explain how to make joints Fixed(will give moment) and articulate (hinged - will not give moment) ? - thank you - From Brazil

hi, i am doing wind analysis of pipe rack structure with bolt connection in transient analysis using one-way FSI analysis. If I am running the analysis with dead load, wind pressure, gravity, and fix supports, the analysis is running successfully, but when I am putting the bolt pretension load, the analysis ran but after 6 7 hours It gives error that solution could not converged. what should i do

Would the results change if you included the actual motor instead of remote mass?

I'm struggling with simulation of Hertz Contact in Ansys. Cannot match the verification value. Could you please make a tutorial about this topic? Thank you

Iam working as assistant manager Design in a Pump manufacturing company I am learning FEA and CFD But I have a doubt as to being a diploma holder, these high end skills will be beneficial in future ? Kindly share your views

can we have the exact model to apply the steps to?

Thanks for the video! I have a doubt like why are you adding the force in lateral direction? It should be in vertical direction la as the weight of the HVAC output act towards downside. Thats the doubt

Informative. Keep it up. Thank you.

Please upload all webinar

Can u explain how linearzed results are obtained using SCP instead SCL. Any reference also would be fine. Thanks

Why didn't you apply base excitation on transient structural analysis

Sir how to change the dimension model if the solid is already build?.. If in solidworks, you can just simply edit the sketch and the solid will follow the new sketch.. But how about the spaceclaim?

Hai sir how are you very long time

Sorry, can I ask you why it gives me this error: Solver pivot warnings or errors have been encountered during the solution?

Have you pro Tipps for spaceclaim in Sheet?

can you model a suspension bridge ( take any cable suspension bridge for example)

The bracket experience a 1200N when loaded, and 0N when not in used. Shouldn't the bracket experience zero-based analysis?

Hi Sir, could you perform a similar analysis for us on a contract? May I have your contact details to share the FEA SOW & requirement

sir, you took wrong value for E as 210 mpa instead as gpa thank you

Sir which version of Ansys is this ?

how will we handle the fillet welds in a shell modelling approach?

Thanks a lot

i saw you imported file. it is means that you already made the design the you imported file in the hypermesh softwer. so my question is What software did you use to make the design that you imported into Hypermash?

In which video you have elaborated about nodes ,remp nodes node edit .. please suggest

Good work sir ..any course regarding hypermesh with abaqus

how to change to first angle projection_ I couldnt find a way.

Hello, the places you appied the fixed support are also fixed in the reality?

Great job RP.

Thanks for your help

What is the specifications required for pc to run 3d software program like spaceclaim and others

How to gotten this step file for practice

thanks for the video, but can i ask you about the geometry? i need your model for my task, thanks

Your content is very valuable, please allow translation into Arabic

Hola muy buen video. como evaluas los resultados del analisis en base a asme seccion VIII Div.2?

One cannot obtain ASME or EN3445 Code Check with Ansys - no client can validate your model so it will not pass Inspection. One can export out of Codeware Compress or PVelite into a Solid Model which can go into FEA. So your Workflow is not in sync. Mickey Mouse!

very helpful

The compensating pressure direction is outward from the flange face. Why is it so? Why it is not towards the flange face?

Is it possible to define the force with respect to crank angle from an outside lookup table

any one provide me ,this geometry link i can't find through blogpost.

Sir how creating this model

Thank you so much for this video. I have question about how to set a Rotationg Force. If I turn Coriolis effect ON in the Analysis setting of Harmonic response, I am unable to change the solution method and it is greyed out to Mode superposition. How can this be corrected?

you made shaft with 4 vertices how you did it?