Will it work on XF 2012

thank you very much for posting this. The procedure did the trick!!

Any luck getting the tank working? The reel handle slips trying to wind up the pressure washer hose.

12-26-24 washing machine drain pump started randomly running and unplugging and plugging the machine in it still ran. Just did this process and she back to normal and running. Thank you sir!

I’ve recently viewed Mr. Flots45’s video and could not resist the urge to put in my 2 cents worth of advise. First, anyone following Mr. Flots45’s advice is setting it’s self up for a possible catastrophic failure and risking being broke down on the side of the road at the worst possible time. The component which Mr. Flots45 would have you have the wire disconnected is called a BMS (Battery Monitor Sensor). The BMS communicates with the vehicles computer and performs a vital function in maintaining proper battery charge. The BMS monitors the voltage on the battery, monitors the current returning to the battery, and monitors the temperature of the battery; all key factors taken into account by the computer when telling the alternator to charge, or not charge the battery. So, by disconnecting the BMS from the computer you will eventually break down on the side of the road. For those who’s auto stop/start does not work, that is an indication you have already have something going bad with your vehicle and it’s the computers way of letting you know.

do i hold start button while i turn the dial

That's the BMS senser that controls the battery charging expect to have electrical problems if you disconnect it 🤦

Thought this was a cool feature when I purchased my 2017 XE, little did I know, it SUCKS. Thanks so much for this video.

thank you did it 2x and it worked

I appreciate the article too I read through that and it helped my washer work normally. I was able to wash my bed linens,thank you so much I thought it was junk,lol

Grazie mille😮

Not all heroes wear capes! Thank you, Sir!!!

Thank you very much for your great article. It saved me a quite a bit of time once again thank you and all the best. Hope I could help you sometime. 5:13

I appreciate that the flaw you found was so easily corrected. I’d rather deal with rough edges than failure to eject or shots going off angle.

Too much profanity

Thank you for the explanation! My model is a 2020 model. I am a senior lady alone. Mine just now started that crazy stuff and it would NOT turn off. I cannot reach the outlet so I found the fuse box and turned off the breaker to it. I have hated this dang machine since I bought it because it is freaking haunted. Mine is model GTW465ASN1WW.

How long after adding coolant will the warning light go off?

You have a ghost in your house. Call a preacher or someone. 👻 👻 👻

Did you check the trigger pull poundage?

Excellent video 😂

Best demonstration yet! Appreciate it brother!

Thank u so much

Thank you. ❤

If this still works on a 2024 FPace. I'll buy the car, If not. I'm not buying it.

Thank you so much!!!!!!!!!!!!!!!! God bless you!!!!! GE series GTW485A

Thanks !! dude worked exactly like you said ...i get home from work the dam machine starts up on its own lol i thought their was an intruder lol nope also thought dam machine was possed lol nope just error code thanks man your video fixed my machine thank you so mutch just si=ubed and thumbs up bro thank u : )

Thank you!! The washer started running on its own out of nowhere. Tried your trick plus had to turn all the knobs and open/close the lid a few times before it finally reset but now it’s working! You’re a lifesaver! 🙏🏻

Thank you so much, it helped

Thanks for your guide even with the new kimber recoil spring i was having a hell of a time getting the slide lock back into position.

Didn't work form mine, but I plugged it in with the button pressed, and turned the know. On 4th turn it shut off and is working correctly now. Newer model with few more knobs...

Well... I tried it. I'll wait 3 days 😊. I'll see what happens. Thank you!

Thank you so much Sir !

Ghosts?

Fkn brilliant 🤗 I totally feel your pain with this user unfriendly feature, thanks for that 👏👏👏

Thank you, Sir! I just did it on my washer, and it is good to go.

It happens. The longer you keep a Jaguar the longer stuff happens…. Jag knows it. Car design and frame is nice but the electrics just suck. Not sure where they get parts from 🤷🏻

Thanks for the heads up!

Just bought a XE S v6. Appreciate videos!!!

Mine just now turned on by itself, like it was in the drain and spin mode. I haven’t used it in like four months because of a drain pipe issue that I haven’t gotten the money to fix yet. No lights, no water in the tub, turning the knobs and pushing the pause button and nothing. Gonna try this and see what happens. Thank you for this video cuz I can’t find any info close to yours! I have the exact same washer

Thank you!!! You are a genius! This worked for me!!

Stuck in flood mode, let it finish then it should be okay.

This didn't work the first time, so I just repeated the steps and after the 4th time it stopped. I immediately ran a load of laundry through and everything is perfect. Thank you! (3/27/24)

Thanks a lot this helped

Thanks a lot this helped

I have that same problem!😢

Thank you! Seems to have worked.

😂😂😂😂I havnt seen mine yet hahaha that was too funny

It worked for my whirlpool. Thank you so much for this video!

Hey Flots45 thanks for the videos. I have the same problem with sharp beaver tail, and browsing KZbin for videos about that problem tonight came across your channel. Just got my Thunder 9 UC Pro yesterday and went immediately to the range to test it. Felt something grinding my web on the first magazine, but kept shooting. Initially thought it was the decocker but realized it was that sharp edge of the beaver tail. I too have large hands, but can't believe that only you have mentioned that problem. Your solution to that is too radical for me though. I will try to put a piece of rubberized talon grips material underneath the beaver tail so that it covers the edges. I have several handguns but lately I was looking for a small SA/DA 9mm with decocker and decent capacity. It came to P30SK and TPR9C for which, surprisingly, I've heard just recently. Upon researching I decided to go with Bersa. The size, capacity, recessed crown polygonal barrel, metal frame, compatibility with Sig Sauer sights, really good trigger, superb reliability.... And all that for 60% of HK price. While looking for TPRC online found UC Pro for a REALLY good price, and was lucky to get an almost brand new gun. The only difference to TPRC that I have noticed is the slightly different slide design and plastic grip shape. Anyhow, so far I like it a lot, just if that beaver tail was designed a little better without sharp edges. I hope a small sticky strip will solve it.

Works!! I had to do it twice👍👍