I am so glad that you demonstrated the removal of the front and rear sights: that you.

Just worked quite quickly on 2/3 brand new G29 mags. The third would not budge, so I had to use my cheap pair of Walmart 4inch bar clamps (everyone needs these!). Also, this method will warp the hole, but you're probably removing these to replace anyways.

Funnily enough watching this on July 4th of 2024 haha

So buying an 80% and cutting slide rail slots which cut through anodizing means it's now worthless by this logic

I noticed you didn’t change the trigger bar spring. Other videos say to do that. So that old spring is working out with those grips? I have an old German p226 and I’m considering the e2.

You really put out a great video series. Thank you, Take care, Be safe.

There are slots in the shovel locking mechanism were the saw blade is used to tighten it. End of knife can be pryed off for storage. The knife is also balanced for throwing

Hey Steve, Great video! I noticed you have Hogue Over-Molded Rubber Grips on your Sig P226 MK25, which I just added to mine. How do you care for/maintain the rubber grips?

Your videos are so thorough and made to look so easy. I really enjoy them. Thank you very much for what you do.

10 years later, they're still hard to find! I just bought one, haven't shot it yet. I wanted a mosquito, but with all the bad reviews I started looking for a conversion kit. I ended up "scoring" one on ebay for under 400 bucks brand new in the box in an auction. That's about what it would have cost to buy a mosquito, transfer fees, tax, shipping, etc. The slide appears well made, hopefully it runs just as good!

Thank you.

Thank you.

i don’t have a screwdriver.. 😭

I don't think that a part that can be replaced is that important. I would look for cracks in the upper and lower receiver. I want good slide rails.

What light is this ?

Super German arm❤

What an absolute waste of time. I wish this could be removed from the internet.

Great video. Installed my grip today with no issues.

I agree with you 100%. I bought the P229 Legion about 3 months ago fell in love with it and now I'm considering the P220 Legion.

Sounds like the exact things grayguns has posted, and anodizing does not protect from wear

Thanks, great video.

I didn't get a new trigger with my short recoil trigger kit.

Sorry "N" means Normalbeschuß!

Thank you sir

Best E2 Grip install video I've seen yet...thanks! Great video, bro!!

When it comes to G26, +2 baseplate for me.

A 1 minute video stretched out to 8 minutes by non-essential jibber-jabber.

nice considering one may I ask a question

cool but huge wast of money

I purchased my Glock 43 Years ago. And from the start, I found the “ New “ Glocks finish easily scratch. Now my Glock 23 Tenifur finish is hard as a diamond. Why did Glock manufacture their newer Glocks with cutting corners and pissing off their Customers???

I've been spinning this stupid thing for an hour at different heights until I found your video. You are my HERO!

Thanks! I honestly thought my cap was soldered on but I got it off.

Not enough room for the optics 😢

To cut through the BS Start it at 4:21, YW!

Enjoyed the review !!

Thanks Steve - Great Video !!

Do modern parts fit on this gun, like aftermarket grips, and short reset trigger?

Great video. Unfortunately I couldn’t get the base plates off my Glock 48 mags

THANK YOU. This is the ONLY video that is of any use to a new mark iii owner. You are the ONLY one that actually explains the little issues that you come across while assembling. Fiddled with it for an hour watching other videos before I came across yours and finally figured it out

Hi steve.... Please explain why the hammer needs to be in the down position during re assembly... It seemed to be very important to the process.... Thanks.

Nice video thank you. Also kudos for reiterating safety. As responsible owners we owe it to those we teach, show and review to always be safe. 🤙🏽

I have the same issue reassembling my 459. My wife has to help me push that lever shown in the video

This was very helpful!

thanks for the video. like.

Thank you Thank you Thank you👍👍 The simple Sig design is what I like compared to CZ , striker fired, H&K, ...and the fact that this is shared with all the P 2xx pistols. Glock does share the same basic simple firing group in all its models and it is a great design, but their frame and ergonomics are very stale. So I'm changing my collection to predominantly Sig Sauer. P6, 224, 226Elite, 239, 227Elite. Keep up your excellent sober, concise, How To's. Cheers from 49.3 miles from Sig Sauer HQ NH.

Demo begins at 4:00min lol yap yap yap. Sorry.

I love the 226 line of pistols definitely some of my favorites.

Good for you a waste to others. Always begin by cleaning and lubricating any metal that touches, impacts, rubs, slides to metal. Friction causes wear. The trigger pull and action will improve greatly from ' out of the box new '. The Legion option is Dubious and the legion helmet thing is childish hype. The Elite option is more real, less expensive, quality over a standard model. ⚖️🗽✌️☮️🇺🇲

I got one of these for a kimber 1911 and I got hammer follow when releasing the slide. Switched back to stock slide release, no issue. No idea why...

4:47: - AAAAAAAAAARGGHHHHHHHH!!!!!!! - He should have used a wooden or plastic pawl from behind the gun. What a fkn clown! The same at 8:31: