Does this work with doors to stop getting offlined

How do I make a count down timer? Lets say, when triggered it will start counting down from 30 (using 1hz frequency)

TAKE A BREATH FFS AND GET BETTER BACK ROUND MUSIC GOOD TIP THOU

Badass..😮

Already knew all this...

How to use the push button. To open doors from the outside. But only allow team member to push the button. Or somehow utilize the and switch, and door controller and hb sensor. I'm not sure how to do that. I made a base with a push button on the outside to open the doors. But anyone can push the button.. any insight or help with this

Thank you, this is still useful. Im using this to implement a pulse system into another circuit that will give sort of an advantage against raiders as a solo. :)

those switches are in my eyes bugged, because when the XOR switch only have 1 input active (which is 1 power) and the other has 0 but that has only power when I turn the RF receiver on) then still it uses 27 power and not just the power send to it which is 1 in this case. So it's bugged. Not usefull in my case. Not sure if i explained it correct but normally if you put 1 power on the left side of a XOR switch and 27 on the right, then it will do nothing but still there will be 27 power used which is dumb. It should only use 1 power for the XOR switch. Pretty lame The AND switch does do the same thing. I send 1 power to it on the left through a RF receiver, and 27 power on the right. When the RF receiver don't send power to it, it still uses 27 power from the right while that can't be the case cause it is blocked sort of speak. The output of the AND switch is 0 and still it uses 27 power. fukked up in my eyes.

These work with ladder trapdoors, try placing it on the frame 😎

lol, shoot hbhf sensor and booms doors open for free.

every usefull !!! thanks!!! subbed

time to blind my enemies with a flickering spotlight

Can’t make this work with night time light js

thanks for the vid my dumbass is small brain and can barley figure this stuff out

your videos are very informative thank you so much

When I power the controller the door shuts, when power is taken away, door opens, HELP

this cleared up a lot. thanks

Works better with a switch and a blocker and a splitter it open all door and closes when the power is off

ty

Omg i was doing this for two hours until I found yours thank you

what do i press E ? it no work

Love the vid man! but for me, it would be great if you could link the videos that your reference in the description.

how do you do the 90-degree and the 45-degree nodes?

jses chech co xD

Definitely a thumbs down.

super useful... a simple 1hz clock is exactly what I need for implementing some more advanced circuits

Each component you connect power to our through takes 1 point of power. If you're limited with power, a splitter may be better off than 3 electrical branches, assuming the applications all need the same amount of power.

Jeeves its hard to tell If you Have 100w Power and 1electric branch and 2 turrets at how much to Set it

Perfectly clear, thank you!

Thank you! your video was very helpful <3

thanks for the help plz make more 🙏

whenever i open doors they just close by them selfs how do i change that?

спасибо, очень полезное объяснение

I use splitters while i know only 1 source of things get power ,like i connect only turrents to battery so max 9 turrents to 1 battery ,if i need put light with it i should use branch. I need to know more.

Speak English

8 minute guide and did not place 1 heartbeat sensor, thanks for wasting my time

is there a way i can implement 2 timers... for say turning someting on for 10 sec and leaving it off for 30 sec

this video is very wrong the sun is on every map different all solarpanels are wrong placed

Note about branches: The branched power will be used whether the energy is actually being used or not. For example if you have a branch outputting to a switch, which is outputting to an auto turret using 10 electricity the branch will be outputting and using 10 of your energy whether the turret is actually using it or not (it does not matter if the switch is flipped on or off). The splitter does not have this energy waste but it can also not be configured to an exact amount like the branch can.

arent u czech ? u seem to have czech accent

this seems useless im tring to get my water pumps to turn of for like 1 minute then be off for like 5

60 Second Rust Tips 8mins later lol. good vid mate

also works for solar panals, if you use an OR switch, you can make your system use solar or wind depending what is generating more energy, and then use a blocker to block battery back up, so you have wind/solar, then battery back up that isn't being drained. Rust electrical is the real end boss

Even though it is unlikely anyone will build it, I just LOVED the timelapse. The trail and error, the thinking, the rebuilding. Amazing video!

why do u stop posting nooo pls post again

Great video thank you friend 💪😌

Vood

Does pressure pads work if you do not know the code to code lock? Want to set up a pressure opener for my heli garage but don't want anyone else to be able to open it

The only reason why true North works and rust is because the rust island system is below the equator that's why you have to have it pointing North not South for the solar panels

If you add a memory cells toggle input as the output of this circuit you at 1 second of on and 1 second of off. Instead of 1 tick of on and 1 second of off