Hi What thickness of plydid you use , 😮did you put any protection between the edg of the ply and the boat to stop any friction damaging the boat material. Many thanks John in Dublin 😊
@ryanferris78414 күн бұрын
Hello John, 12 mm ply and I rounded the sides and then covered with tape thick duct tape or Rv tape will do the trick! I have a few other videos explaining the tape etc!! Is the fishing any good on the east coast 😀
@BlackRussian3116 күн бұрын
And there was me thinking you boys will be heading to the maidens chasing the pollock.
@ryanferris784116 күн бұрын
The very thought of being out in that gives me the fear 😨
@BlackRussian3116 күн бұрын
Do you think it’s worth a throw when the weather settles?
@ryanferris784115 күн бұрын
@@BlackRussian31 always
@stephenjones44117 күн бұрын
Keep the wee boat in the garage 😂
@ryanferris784116 күн бұрын
😂 madness mate
@gatti49319 күн бұрын
Good point ! I could pack the middle with something I suppose?? Or would you recommend a different seat , or another honwave ridged bench seat ?? What would you do ?
@ryanferris784118 күн бұрын
I would pack the gap with something inflatable like an inflatable pillow or an old life jacket however it will need to be tightly packed
@gatti49318 күн бұрын
@@ryanferris7841 Yeah, I'll find something, cheers pal 😉👍
@ryanferris784118 күн бұрын
Welcome 👌
@gatti49320 күн бұрын
Hi pal , I'm looking at getting one of these seats but I'm not sure which size to get ?? I have the honwave t38 V Air deck and its 80cm wide inside, These seats come in 2 sizes 82cm and 94 cm , could you enlighten me as to what size seat I should get for a T38 ??
@ryanferris784119 күн бұрын
Hello! For the t38 you will need the smaller seat however bare in mind the t38 hasn’t got a flat deck therefore the seat won’t be fully supported in the middle and may cause it dip in the middle as you travel
@adventurelover695522 күн бұрын
I am in the middle of buying either T35 or T38. I cant decide which is better.
@ryanferris784121 күн бұрын
They both have there pros and cons how for me the t38 has more pros
@adventurelover695521 күн бұрын
@@ryanferris7841 is it a durable boat with long life span?
@ryanferris784121 күн бұрын
@ t38 is very durable in fact the hull is made from better material than the hull on a t35
@foxfai127 күн бұрын
what board is that?
@ryanferris784127 күн бұрын
Decking board!
@Barbedhookfishing27 күн бұрын
😂😂 very good 👍
@ryanferris784127 күн бұрын
Stop you complaining mate!! You now have rod holders 🤣
@Barbedhookfishing27 күн бұрын
@ryanferris7841 can I request another 2 please 🤣😆🤣😆
@KevinOR-u2wАй бұрын
Thinking of adding a plywood floor to an Air Floor boat? If so, did you put the Air Floor over the plywood or the plywood floor over the Air Floor? Or did you get rid of the air floor altogether? I am considering adding a plywood floor but maybe from the transom up to the start of the bow where it starts to taper. Any thoughts, advice? TY ! (Saturn SD 330 W - Wide)
@ryanferris7841Ай бұрын
Hi, Ok so my boat hasn’t got a separate air floor it has a built in keel/floor it’s part of the boat and cannot be removed my plywood floor is only a deck and provides no structural integrity whatsoever. In your case your air floor provides structural integrity and is needed to stop your boat from flopping about! Therefore a 12mm ply deck placed on top of your air deck is 1 option and probably the best option Option 2 take the air floor away completely and construct a deck however this will need to be made from stronger materials as it will replace the air deck and will be structural.
@KevinOR-u2wАй бұрын
@@ryanferris7841 Thank you! I just watched your video of when you first installed the floor... I understand now... Thanks!
@ryanferris7841Ай бұрын
@@KevinOR-u2w Thanks 🙏
@hansmustermann9255Ай бұрын
Speed is in kn, km/h or mph?
@ryanferris7841Ай бұрын
Hello mph!
@hansmustermann9255Ай бұрын
Thanks
@ryanferris7841Ай бұрын
You’re welcome
@mikama2322Ай бұрын
Thanks but I mean the Dimension of the keel or what is that on the backside?
@ryanferris7841Ай бұрын
Sorry I haven’t got the keel support measurements to hand I need to take the floor out to measure it which I will do and get back to you! Its just a piece of wood
@mikama2322Ай бұрын
Hello.Nice Job. I have a question. What kind of wood do you use? What is the bridge under the board for and what are its dimensions? Kind regards
@ryanferris7841Ай бұрын
Here you go- 12mm plywood 202 cm long 96 cm wide at the stern tapering down to 86 cm at the bow end! Make sure you notch out for the drain plug and cut to clear where the tubes join the transom! All above is a guide only as other t38s may vary slightly! I appreciate your support
@BarbedhookfishingАй бұрын
Perfect
@KevinOR-u2wАй бұрын
Nice set up! Where did you get the flooring? Thanks!
@ryanferris7841Ай бұрын
Thanks I made the floor and bought the EVA foam on eBay! Check my other videos
@roberthowie8538Ай бұрын
Hi Ryan could you please give me the total length of your setup with the t40 on the trailer as I can see it hangs over the back of the trailer I have a small amount of space to keep it I just want to make sure I have enough room for it before I buy one. thanks Rab
@ryanferris7841Ай бұрын
Hello Rab! I no longer have the t40 however the tubes are meant to overhang so the transom supports make contact with the bottom of the transom! If you get me
@roberthowie8538Ай бұрын
@@ryanferris7841 Thanks Ryan I knew the tubes would be hanging over the back of the trailer I was just wondering for total length as I am limited for space
@ryanferris7841Ай бұрын
@@roberthowie8538 ah ok! T40s long gone.
@fcojavier9119Ай бұрын
Hola, esos asientos le quedan de 10, ahora falta montar unos cañeros y mas cositas guapas, estoy deseando que la dejes bien guapa y nos la muestres, muchas gracias por compartir tu capricho con nosotros Un saludo
@ryanferris7841Ай бұрын
Thanks
@DannyspinningtailsАй бұрын
Hi Ryan was passing by and left my little business card with my mobile on it for you so we can chat about getting out fishing. I am staying just up the same hill minding the 3 sausage dogs for a few weeks. Ps it’s not a real business lol. 👍
@YorkshireBitsnBobsАй бұрын
How did you get back into the boat?
@YorkshireBitsnBobsАй бұрын
Good to know and great to watch. Was looking at lake annecy & Bourget in france as well which are hopefully the same. Been a couple of times to Port Grimaud / St Tropez which was great and also no issues. Did you launch from the campsite?
@BlackRussian31Ай бұрын
Nice one my friend, our we country has so much to offer. Cheers
How is this going for you a few months later ? Is there anything you would approach differently ? Any issues with chaffing or debris. I got a t38 a month ago and this was in my mind when buying it .
@ryanferris7841Ай бұрын
Hello everything is perfect so far with no problems whatsoever all positive! I say go for it 👍
@davidcollins9817Ай бұрын
Great - thanks for the response ! Good to know . I’ll give it a go. Not the biggest investment in the world .😂 I was thinking of a hard foam board rather than ply but will try the ply first ! Thanks again 👍
@ryanferris7841Ай бұрын
@@davidcollins9817 you won’t regret it
@garycaldwell2776Ай бұрын
Nice fish mate tight lines 🎣on
@ryanferris7841Ай бұрын
Tasted great too 👌
@garycaldwell2776Ай бұрын
Happy days 😁well worth it then 👍
@ryanferris7841Ай бұрын
@ definitely 👍
@philwebb606Ай бұрын
I was fishing of the rocks at ballygally on Friday, it looked calm over to the maidens, obviously not
@ryanferris7841Ай бұрын
SW winds commands calm waters within the headlands, it kicks up when you go beyond lol
@michaeltodd6779Ай бұрын
Cracking fish
@ryanferris7841Ай бұрын
Thanks 🙏
@Meals_on_wheels.Ай бұрын
Nice video. Do you keep any or put ‘em all back?
@ryanferris7841Ай бұрын
Put most back! However I’ve some lovely fillets in my fridge now 😄
@BlackRussian31Ай бұрын
Brilliant video, another successful day for you guys.
@ryanferris7841Ай бұрын
Thanks pal!
@BlackRussian31Ай бұрын
Appreciate the reply, keep up the good work.
@DannyspinningtailsАй бұрын
Well done sir ! Nice fish
@ryanferris7841Ай бұрын
Thanks mate the place is teaming! Would you be up for a run out?? Arron or myself would be happy to take you.
@DannyspinningtailsАй бұрын
Most certainly Ryan. I’m still in California for another week but I will touch base with you sir once settled back home in Larne. Some screaming reel takes great video. 🎣😊👍
@ryanferris7841Ай бұрын
@ nice 1 enjoy your holiday
@DannyspinningtailsАй бұрын
@@ryanferris7841 I’m with Erin ( your best customer ) at her grandads helping take care of him. They treat me like family.
@ryanferris7841Ай бұрын
@@Dannyspinningtails I gathered that seen your car parked up lol
@BarbedhookfishingАй бұрын
Some lovely donkeys out there today!! 🎣
@ryanferris7841Ай бұрын
Two of the biggest donkeys were in the honwaves 😂
@G-winnАй бұрын
Do you do your own servicing on your Yam 9.9? would make a good video 👍
@ryanferris7841Ай бұрын
Na mate them days of servicing outboards are over! Too much mess and I’ve none of the correct tools.
@RazielKBАй бұрын
What a fish, i love how calm and controled throughout the fight you both where i can tell your both season pikers. And got me itching to get back piking. Tight lines and thanks for the content
@ryanferris7841Ай бұрын
Thanks pal we fish a lot together we are well use too each other! Stay tuned and thanks for watching.
@divexplore21Ай бұрын
Nice bit of fishing there. Got my new Yamaha 9.9hp, trying it out tomorrow on the T38, can’t wait.
@ryanferris7841Ай бұрын
Nice 1! I hope to get out this weekend the weather great all week good luck
@gatti493Ай бұрын
Love it lol , great video , what is the back rest seat like ?? Can you put me onto them please 😉👍
@ryanferris7841Ай бұрын
The seat is very good however it take up quite a bit of room
@gatti493Ай бұрын
Just one other thing, what width is your ply ?
@ryanferris7841Ай бұрын
12mm 👍
@gatti493Ай бұрын
What a fantastic video and a great resourceful job , I am going to do something like this with my T38 but I'm thinking of putting foam matting , that interlocking stuff under a piece of ply about a metre and a half by the width of the boat to sit my scuba tank on . This is our first dinghy and I'm not sure where to put a ladder to get back into the boat or the strongest method for fixing it ?? Any advice would be appreciated 😊
@ryanferris7841Ай бұрын
Thanks 🙏 I got the inflatable seat on eBay at the time however the buyer is fine now ☹️ however if you do manage to get 1 it’s the smaller 1 you need for a t38! I thought about getting a ladder myself however I wasn’t sure how to mount it so I didn’t bother lol
@gatti493Ай бұрын
I think it may be a case of putting a few D rings somewhere for a ladder , I'll have to check Google for D rings and glue ? Thanks 😉👍
@lawrencemacd63Ай бұрын
Cracking fish well done Aaron Lordy Scotland 🏴🇮🇪🐟🎣
@BarbedhookfishingАй бұрын
Thanks pal 👍
@MrMichael1710Ай бұрын
Great job! Trying to do the same for mine for next season! :) Any measurements for the keel support available?
@ryanferris7841Ай бұрын
Hello sorry for the late reply when I take the floor out I will measure it for you! And get back.
@conorcoulter7071Ай бұрын
Class
@ryanferris7841Ай бұрын
🤣👍
@baitrunner5193Ай бұрын
Brilliant lads
@ryanferris7841Ай бұрын
Thanks 🙏
@whitetroutchannel2 ай бұрын
its a pilgrim not a toby, toby got fins, if your snaggin on weed bad fire on the singles, nice night 4 it mate 👍👍
@ryanferris7841Ай бұрын
A few snags about once i figured out what direction to chuck the lure it was grand 👍
@whitetroutchannelАй бұрын
@@ryanferris7841 if you get the singles with that mylar strand on the back it can be explosive for them mate 👍👍🎣
@Deathst4lker2 ай бұрын
Top quality lads! Great craic, decent fish, Guinness to celebrate - now that's a good day 🤣🎣👊
@ryanferris78412 ай бұрын
Good times 😆
@andymoffat83932 ай бұрын
Can you give me the measurements for this ?
@ryanferris78412 ай бұрын
Here you go- 202 cm long 96 cm wide at the stern tapering down to 86 cm at the bow end! Make sure you notch out for the drain plug and cut to clear where the tubes join the transom! All above is a guide only as other t38s may vary slightly 👍
@andymoffat83932 ай бұрын
Thank you so much. Enjoying your channel. I have the t38 with yam 9.9. Would like to put a floor in and maybe even a steering console eventually. Can the yam be converted to work with a steering wheel
@ryanferris78412 ай бұрын
@@andymoffat8393 thanks for your support 🙏 I do believe the 9.9 can definitely be used with a console! Good luck with your build