SubieSpecs

Пікірлер

@jamesblack683 20 күн бұрын

Heya mate.nice video. I have a omega myself which is a 1600 fwd .I've had it for a few years now.good little wagons and tes parts are pretty hard to come by especially in nz haha

@tiaelliott6651 Ай бұрын

Wish I found this video before ripping tf out my intake hose……😅

@humphreykimathi3856 2 ай бұрын

Hey Reuben.. can you show how the sunroof can be repaired or replaced

@autoshopturbo 8 ай бұрын

Reuben these videos are so helpful & edited so nicely, thank you for taking the time to make these!

@BO0O0O0O0O0O01 8 ай бұрын

I need this quality of video to walk me through replacing the twin turbo inlet hose, I got a silicone one to put into my 02 rev D. I'm scared of messing up or forgetting something this definitely helped my confidence for removing the intercooler though!

@SubieSpecs 8 ай бұрын

If ya can wait a month or two, I’ve filmed a vid on how to remove the manifold on an ‘02 Rev-D. It’s a few spots down the video queue though.

@BO0O0O0O0O0O01 8 ай бұрын

@SubieSpecs I unfortunately can't wait, I'm going to pull off the intercooler today and evaluate my next step from there. I've already removed intake and airbox. I got to get it up and running quickly now that I have a new inlet. I don't have a garage, and we already have snow in the forecast for next week :/ I will be sure to watch your video when you do post it. Then I can see what I did wrong, aha!

@BO0O0O0O0O0O01 8 ай бұрын

@SubieSpecs I also found a post that I'm pretty sure you wrote in regards to these cars, has vacuum diagrams for each revision, and kind of what not to do. It's very well written and I'm sure to reference it.

@SubieSpecs 8 ай бұрын

Yup, on SL-i.net, it should help. One thing you should do is order the crank case breather stand off, and F-pipe tee piece, for the PCV system. These will brake. Also be mindful of, and don’t snap the nipples off your evap solenoid. Those are the big two common mishaps.

@BO0O0O0O0O0O01 8 ай бұрын

@SubieSpecs I'll see if the shop I use to let deal with the car can order those parts for me! I'll need to buy a new intake manifold gasket anyhow! Thanks for the heads up, I was told that it was pretty inevitable that some pvc was going to break once I got in there. I wasn't sure what, though. Any idea what fittings I'll need to get for the new silicone inlet? I was told by someone that the factory ones couldn't be reused as they're formed as one with the oem inlet.

@xzaviervillagran3191 10 ай бұрын

Need aftermarket parts for EJ20 any recommendations? I have a 1996 Subaru Legacy RS (Right side drive) JDM

@TMWSTW-hy5ph 10 күн бұрын

What are you looking for?

@notenoughregos 10 ай бұрын

Awesome series so far mate! I've got an 83 wagon myself, and am planning on swapping an EJ20 or EJ22 SOHC into it. Also owned 3 L Series previously :D

@whiterussiandude 10 ай бұрын

Pretty cool

@matthewesler8379 10 ай бұрын

Where did you find the service manual

@SubieSpecs 10 ай бұрын

EBay I think. Mitch (the owner of the car) bought it from the US.

@matthewesler8379 10 ай бұрын

@@SubieSpecs thanks you

@573417H45 11 ай бұрын

Keep up the good work!

@user-gw5lc4th3d 11 ай бұрын

Интересные ваши видео, у отца leone с 2008 года по сей день, привет с Украины👍

@SubieSpecs 11 ай бұрын

Thanks for watching! Hopefully his motor is better health than this one 😅 Stay strong over there, слава україні

@haac4825 Жыл бұрын

Great Info. Thanks

@haac4825 Жыл бұрын

Looks Amazing.

@haac4825 Жыл бұрын

Subscribed. Like it.

@westy1 Жыл бұрын

Best yet,keep em coming ,too good :)

@dodgesteelenterprises Жыл бұрын

all these comments, nobody talking about how perfect he timed those impact driver shots with the music, kudos to you sir. I will return when I have banter about my 2003 BH5 GTB.

@haac4825 Жыл бұрын

Love it. Like the cranberry colored GT wagon.

@Jestr86 Жыл бұрын

Beautiful !

@_Hani_26 Жыл бұрын

I use a dowel pin puller for cylinder head dowel pins. Works kinda like a slide hammer. Real handy. Might not be real easy for you to come by one tho.

@cloutcheese Жыл бұрын

very well edited, making NZ proud

@IZichard Жыл бұрын

Headgaskets and intake gaskets aside it actually doesn't look too crusty, proper carnage from the headgasket failure though. I love how many headbolts there are, imagne how much boost it could hold with and MLS gasket!

@SubieSpecs Жыл бұрын

Right next to the fire rings too. But the rods would probably pretzel long before that was an issue😆

@christianstockle7116 Жыл бұрын

Thanks for the video, very helpful. I have a 2005 2.0ltr non-turbo that I need to flush. Would you say it's pretty much the same process as your model year? Cheers!

@SubieSpecs Жыл бұрын

Basically. When bleeding, of you don’t have a bleed nipple, just crack the top hose off the rad a bit to let the air our.

@christianstockle7116 Жыл бұрын

Thanks bro!

@IZichard Жыл бұрын

Dis-guuuust-ting! Coolant spilling out into the back of the car is always lovely... looking forward to the next episode

@ShaleNinja Жыл бұрын

The bitey bin chickens 😂😂😂

@musguelha14 Жыл бұрын

Crazy production quality for such a small channel, congratulations.

@fsfs555 Жыл бұрын

The EA cars, and especially the EA82 engine, didn't get a lot of love aftermarket. Most people prefer just to EJ swap these. It's not just the engine, though: basically any suspension part is NLA, especially if you keep the air suspension (this car looks like it did have it but was converted to standard struts at some point). I have an RX/II coupe (just the RX in the States), an XT6, a BRAT, and formerly an XT Turbo, so I'm familiar with the pain of trying to keep these things on the road after >30 years.

@SubieSpecs Жыл бұрын

Yeah it sure was a mish! Very satisfying getting to go through it all though.

@kiwizookoffroad2040 Жыл бұрын

Sweet! Need to come to Christchurch and get to work on John and my collections! 😂

@SubieSpecs Жыл бұрын

Moving up in 2 months!

@kiwizookoffroad2040 Жыл бұрын

@@SubieSpecs nice, was that your Legacy wagon?

@SubieSpecs Жыл бұрын

Green one? Yup. It’s my work ute basically. Vid series coming for that one next year.

@stevewandel9317 Жыл бұрын

No air conditioning made that much easier. Got an extra electric on the radiator and need to unbolt the compressor off the engine and move over to the side (otherwise need to regas)

@SubieSpecs Жыл бұрын

Oh no doubt, much like with my TT engine out vid. It sure was nice dealing with something so simple for once though!

@gojogingo Жыл бұрын

とてもよい

@kimandjax Жыл бұрын

MMmmm pooo water! *achoooooooooooooooooooo*

@SubieSpecs Жыл бұрын

Disguustin

@patcho85 Жыл бұрын

loved the presentation on this one Reuben!

@pkthtguy587 Жыл бұрын

It's awsome seeing a classic on NZ's roads

@churchofseabass9227 Жыл бұрын

I got under mine today, its a 2015 crosstrek with electronic steering, found that if I push on one wheel at 9-3 o'clock, it will wiggle like bad tie rods, however the opposite wheel also will wiggle at the same time. Hoping it's just a bushing holding the steering rack but i'm afraid the whole rack is bad. Seems the rack should lock and have no play when the vehicle is off.

@SubieSpecs Жыл бұрын

What you are looking for when looking for play in the rack mounting, is not for movement in the wheels, there will always be some movement with the wheels themselves against the steering lock. What you are looking for is movement of the rack itself, relative to the subframe. Those late model racks have a superior mounting setup to the old rack in the vid, and actual play in the rack mounting on them is very rare compared. When looking for play in the tie rods, you’re going by feel, and listening for the little tick tick of it’s play, it’s not a visual inspection for them. It takes some time to master these inspections, the cues can be very very subtle! Hope this helps.

@patcho85 Жыл бұрын

man turned out a treat! really enjoying this series!

@bmxsquid Жыл бұрын

Awesome content! Would love to see some of your BH legacy too!

@SubieSpecs Жыл бұрын

Not mine! Flatmates. Filming a vid on it in a few weeks, need to take the manifold off for fuel hoses, surprise surpruse.

@thesmokingcap Жыл бұрын

I forgot how warm it was outside back then haha. That engine bay cleans up nicely

@IZichard Жыл бұрын

Before and after looks great! Just need to get that wrecker pen off the AFM and she’ll be mint 👌🏻

@dacerx Жыл бұрын

First. Good job bro

@rafalsachanowicz9277 Жыл бұрын

hello, maybe you can help me with my project. I am the happy owner of legacy gtb ej20H1997 Japanese imports. I fulfilled my childhood dream, but after renovating the engine and the entire suspension, etc. after 2000 kilometers, the 9H ecu burned out and I decided to install the emu master black. but i can't find the pinout anywhere. do you have any schematics?

@SubieSpecs Жыл бұрын

I suggest you join the 2ng gen legacy enthusiasts facebook page, and the SL-i.net forums. I frequent them and upload all the data I have. I presume that because you said EJ20H and GTB that it is a facelift auto. In which case you are out of luck, I do not yet have wiring information on the “1-plug” ECU’s auto facelifts have.

@rafalsachanowicz9277 Жыл бұрын

@@SubieSpecs Thank you so much i will try

@dougrosendale642 Жыл бұрын

Nice video, thanks man. This and your thread have been very useful. Where can I get one of those 14 mm wobble sockets? I can't find any online (in nz).

@SubieSpecs Жыл бұрын

I bought mine from the local snap-on truck. Bout $100 for one, but honestly worth it. If you want a snap-on one, google your local truck, give him a bell, and find out his routine. Local guy to me is Invercargill based and comes up to qtown fortnightly. Other manufacturers do make very similar sockets, koken is the Japanese version of snap-on, hobeca trading sell them, they supply repco’s, so you can go that way. Otherwise teng tools might be a good intermediate brand.

@bmxsquid Жыл бұрын

Awesome channel. I'm going to have to watch all your videos, glad I found someone who's working on these.

@Ngatira98 Жыл бұрын

Nice one Reuben, as to be expected. And the vinegar works a treat eh!

@autoshopturbo Жыл бұрын

Cheers & thank you for the steps to remove the heatshields. You saved me a couple hours haha.

@-smokintrees-8590 Жыл бұрын

Have a 2000 legacy gt and mann did this help. Ran into a little bit of an issue reinstalling the intercooler and ended up mangling the plastic oem hoses from the turbos.. thats okay though, i just bought a 1999 legacy gtb e tune as a parts car, and i plan on swapping the intercoolers and tubing (next time one of the many coolant lines spring a pinhole leak and i have to tear everything apart) Lol atleast i am a little wiser this time around. It is currently winter, and i wont be driving the car for a few more weeks, any info on weither an aftermarket silicone hose in place of said hoses is a good idea? Where if anywhere could i find a pair? I can barely find anything about these cars specifically on the web. :( Any info helps, thanks and have a great day!

@justcloak3223 Жыл бұрын

Yeah these cars are rare af to find parts, you'll just have to diy with some hoses and do some measurements. I had a boost leak in primary hose and intercooler itself so i just replaced whole thing for like 350$ But it works awesome now so it was worth

@2smoker311 Жыл бұрын

thanks for this the video came out just as I was about to take out mine

@ethanliu3485 Жыл бұрын

Awesome video, considering pulling the engine on my BG5 GT-B as its a bit leaky and old, this video and your last one gives me some confidence!

@IZichard Жыл бұрын

Another great video! I’m impressed at how well the vinegar worked, I’ll have to give that one a go.

@texr2000 Жыл бұрын

You make this look annoyingly easy on an engine stand..... Interesting, i thought just before you said it that looks very clean inside. When I did mine few months ago was far more golden with 140km on the clock

@SubieSpecs Жыл бұрын

I’ve had the debate about what causes the gold then brown then black staining. I’m convinced it’s old oil with long service intervals that does it, as the oil brakes down and collects more carbon and crap, thats when it starts depositing it on the inside surfaces.

@DaBlueMonster Жыл бұрын

Great Video! 💯👍🏻💯

Ең жақсы KZbin

Пікірлер