My whole assembly is rusted shut, impact doesnt work.

Is there any room to add extra insulation between the liner and the roof?

Holy crap just dropped the freaking fuel tank it's a lot easier than taking the liner off and taking a box off are you kidding me

Spray some WD 40 on the bolts from under the bed making it much easier.

Found On The Road Dead and Fox Or Repair Daily. Som e stereotypes are true. Well FORD rings true but if you want it you can say it out loud. But know Elizabeth Ford bet on KC to win and they own more of Boulder City making them Mormon s

Mine came with stock 8.8 and 556 gears. If it wasn't for that I don't think the engine would pull my trailer 🤣

I HATE MUSIC IN DIY VIDEOS........................except this one. lmao it slaps!

That is nowhere near the hardest trail in Nc 😂😂 go up the front ledge of Daniel at uwharrie with a stock 2wd ranger it won’t happen

Thank you very much, you made that very simple and quick. I have an additional comment, Dorman part number 14055 fits perfectly, use the clear one. Found it at O’Reillys thanks for the help!

Dude!! One of the absolute BEST instructional videos that I have seen in years. Very concise, yet all important details covered. Excellent camera work! Stellar work!.....Of course I subscribed!

Big brain time!!

How much did auto zone charge you rent the fuel pump kit? They quoted me $135 to rent it, but to buy it's $124 on Amazon. How did you go about renting the kit?

The only way this is a difficult trail. Is your "offroad" experiences are gravel driveways. And now they have just graded it. It is less difficult.

Ol danger ranger.

Eagerly waiting for my fuel pump to go out so i can go flat bed.

I had an accident and damaged the rear gate on my 2007 Matrix. I have not found a video on replacing it. The problem is that I have been unable to remove the hinges from either gate. Any thoughts? Thanks.

Thank you from Alabama!! This helped me big time today!!

Question when you put them back what lube did you use to slide them back in

its not the electic thats the problem its that's a very weak impact...i have one of those...its only 1/3 as strong as a medium milwaukee - a medium milwaukee will take almost anything out, and if it can't then the heavy one will 100%...i keep one of those in my tools for when you need the heavy artillery

Brake fluid is extremely flamable

So it starts in Detroits and goes to St Helens and back to Detroits?

Holy shit, ive searched for my entire life for a video to be down and dirty, quick, without the person ranting like an idiot for 15 minutes. Well done my friend. Thank you so very much. Take Care

I like it. Add a H2 top to the snorkel.

Oh hell no!

Ford frickin ranger ranger . I got a 2000 with 149,000 on it .

Why did you change it? Trying to figure out if it’s the pump or filter

Your not very smart. And the video is blurry. You must be on drugs

Nice music! Although I may drop the tank. It would take longer to slide the bed back, for removing the toolbox and bed liner would take longer. Also, I've got to drop the fuel tank to get to the blown brake line. Which chose to blow in between the fuel tank and the frame. 🤔🤷 The current fuel pump is 27yrs old and the original factory one.

Nice job on this video. Very clear and easy to follow. Thank you

Mine has been leaking fluid for 15 years when the weather gets cold.. I never see fluid leaking or on the ground nor around the bell housing and or fire wall.. WTH could be the issue?

Oring tool. Or just slip a stiff thin smooth awl, very small screwdriver or other and pry them off. Lubricate with silicone oil first. Not silicone mixed with distillates. Or other fluid not harmful to rubber. Razor is sharp and can easily score the outer wall.

After getting broken pin out , going to replace with a new stronger Pin that I will make vs the same pin that will shear off again the next time.

I didn't hours trying to use the plastic tool that came with. Went to the parts store and got the metal version and it released within 5 minutes. Now what were you saying about blowing the seals? Don't press the clutch until everything's back together and you have brake fluid in it?

Thanks bro lifesaver and money saver hell yea information goes crazy when you can actually obtain it

lol I had to get my bed off with 1/2 ratchet and a 24mm wrench for leverage.

Question: What is the path of the antenna wire? Does it go down the front by the windshield, or between the front & rear passenger side, or somewhere else? I have to replace mine but want an idea of the path before I take it apart. Thanks.

GREAT VIDEO! For my exact project Ranger year and model I bought last summer finish8ng it’s full restoration after it sat in a garage in storage after kid who owned it passed away his mom parked it in 2002 I found it 2023! Had to redo a lot as it was not properly stored but looks like it just came out of the factory. After this will drive like it too hopefully lol Thanks guys very well done no waste no fluff. You’re awesome!

It did thanks

You missed the million dollar chance to soundproof the roof metal

I had no idea the beds came off that easy . I had my broken fuel line near the tank fixed , and no telling how much money I saved by not having it towed.

Great call on the tool loan; that's indispensable. Also, thanks for showing things on the new parts from there removal or again once it's out for clarity. Just finished my swap out and took about an hour and a half for anyone wondering about time frames. Thanks for the info, guys.

Great informative video! Someone was looking for help and I found your video and shared it with them. Also helps me out cause I might have to change my fuel pump assembly. The other day my gas gauge dropped to empty and the fuel light came on right after filling the tank 😂 2 days later the gauge worked and was back to normal and a week later the same thing happened again. Watching the video definitely helped cause I didn’t want to drop a tank in my driveway. Mine is a 2004 Ranger XLT. I subscribed as well. 👏🤜🤛

I’m sitting on the side of the freeway waiting for a tow truck after my fuel pump on my 98 ranger went out. This video gives me much hope that this problem is easier to address than I thought. Thank you!

I cut the heads off a couple bolts and slotted the top and put those in the top holes to make sure the gasket is aligned. Put in bottom bolts then screw the top bolts back out. Works good.

Sh1t. I need more tools

What did you pull this off of?

Really detailed video thank you for taking the time to teach all us how to do this sir

If you have a engine hoist and some rope/come-a-long straps then use that to take the bed off. Makes it a 1 peson job.

One of the best videos I have seen, great detail.

The 8.8 swap was so worth it on my 1992 Ranger. Managed to grab a 3.73 LSD, disc brakes and swapped over an 8.8 aluminum cover from a 2002 Explorer for less than $170 at my local junkyard then sold my stock rear end on OfferUp for $250 😂