Am I hearing some choice words at 15:00? Great video! Thanks! 👍👍👍

Transfer box brother! lol

Kind of look like they are upside down

Hey there, brother.. You did such nice video, Don't be ashamed for all the work and the time you spend on your car, Believe me, brother, you Lorne us, but the fact is all the experience you got from all good job that you have done, and that is the best way to Lorne it ... By the way, you mentioned the auto part where you ordered the bolts. Can you please let us know the name, please? ... I was focused thinking the way to remove the leftover bolt head, and i didn't catch up with the name of Store.. Thank you for Lorne us with a very good and excellent video... Very Good Job

M100 and M200 are underrated cameras...very compact and a lot of features and nice sensor. just paired with a 22mm canon for pocket or a 16mm sigma for studio. I also use mine with a 300mm for the moon and tele 😂

I like the M200 for streaming and with the Viltrox lens adaptor and speed booster you have a huge choice of lenses. Both of which also fit the M50 mark 2 which I use for video and content creation. With the Canon Eos webcam utility both cameras also make excellent webcams with a clean HDMI out and a very decent image quality.

Did you say how many miles were on it? Thinking about buying a 2005 with 136k on it.

you didnt show pulling the cv axle out, which is why i was watching

You can get a front differential for a few hundred bucks but I bet it was th front driveshaft that made all the noise . And how is it only worth 400 bucks if you just spent all that on front end parts ?? I know this is an old post but also did you refill the gear oil after this job ?

How much did you pay for the parts you changed?

The person who designed the front end on these needs kicked in the nuts a few times.

"Promosm" 😩

There's no in body stabilization in this camera. The IS in the menu is for LENSES with IS.

Thanks for the video! I feel confident I can replace my cv axles now. Didn't have the same sound as yours, just torn boots, leaking grease.

great video. I took my clutch fan off buy grabbing the water pump pulley on the top with a heafty vice grip..which rested to the right of that large bolt you removed later on. then I used a pipe wrench and the nut came loose with minimal effort. i dropped the clutch fan (without it falling to the ground) downwards and picked it up from below. the belt stayed on. easy peesy..

It’s the cv joint on the front driveshaft for mine.

I have two Canon M200’s and two Canon M50 Mark II’s. On both of them I use Viltrox Speedboosters to adapt them to EF lenses. I use these EF-M cameras when I don’t want to lug around my Canon 6D Mark II or my Canon T7.

I am so surprised and happy to see Cristopher’s post about the two cameras I have been using for long time. For my old M50 I used a speed booster for my Sigma Ef-s 18-250mm lens and I have just purchased the Canon Ef-s 15-85mm. I use this camera for outdoor and other activities. My M200, boy I love this little camera, I use the 22mm fantastic little lens and the old 18-55mm lens that came with the M50 some time ago. The M200 camera setup I use is for any inside the house activities and I have been very pleased to display my photos to friends and relatives as they love my work.❤❤❤

❤😂

Do u still have it?

Thank you it's been so hard to find decent info on maintaining this dang car!! That's what I get for getting an 06 car in 23 I guess.

You should've changed your diff bushings while you had everything apart.

What a great video thank u so much

need dot 4

I’m doing mine now because I’m emergency brake spring was bent and I can’t find no find on it 😫😫😫

22mm F2 lens is not stabilized. Kit 15-45mm lens is stabilized. Stabilization is part of lens not camera. You need stabilized lens to activate IS in menu. You can find it in lens specification. It is not camera problem.

I figured out the hard way the parking break came out with the rotor I couldn’t figure out how to get it back on until I released the parking break I was able to get it back on

Thread tape not lock tight

After watching this i will not attempt it

Wheel spacers are fine, man you could run 10 mm and that's like 1/4 inch and be fine 😊

Hi. Can you write, please, the sizes of the sockets that you used in this work? Thank you.

Bought 2 holsters 1 yr ago and 1 was better than the other. Just ordered holster n mag holder 11 days ago and nothing. Took my money same day though. Tried 5xs to contact them. Crickets. Never again.

same here, Wife has a new one, need another holster

I've been using O'Riley universal 50/50 on my 06 4.7 Commander no problems I think Jeep made that shit up so you only buy their products

Had the same problem, unfortunately had to look for another set of wheels. Ended up getting steel Jeep wheels from a wrangler with no problems

I .bought the M200 for its small size and weight but found the buttons too tedious. Ergonomically poor with no front grip. On/off button is too small and difficult to operate. To make any changes in settings the display screen must be navigated. No mic input or a hot shoe, even though the M3 has both of these and cost $100 less?? Also, the M3 has a higher overall score in other independent reviews. So you are quite correct about the camera being "crippled".

I think you need to replace the shock bushing in the lower control arm.

LMAO

Stabilization doesn't work with all adapted lenses like you say here, it only works with lenses that have their own IS. That's why none of the primes support it, because the digital stabe only applies to video by simply cropping the frame. It cannot do anything for stills, no matter the lens. For IS in photos, you need a stabilized lens, not digital IS. If it were IBIS, then your complaint would be legitimized. Nonetheless, nice video on two awesome cameras! I love my black M200 with the brown leather grip case, i take it everywhere.

Ford is also recommending DOT4 brake fluid for these cars.

Sorry to hear it was your differential! I’m trying to figure out if you had similar symptoms like I’m having. When im driving 20-30 mph and above going straight or turning to the right I get this rubbing and vibration on the front drivers side, but if i slightly turn/swerve to the left the sound goes away completely. Basically when you take the pressure off of the drivers wheel the sound and vibration go away. I’ve changed the wheel bearing and rotated the tires and still have the issue. I also changed the propeller shaft last year and that’s still fine. Just curious if you had the same symptoms. Thank you!

That should last longer than a couple of years. I bought my Commander in 06 and still have the original door handles working fine. However, I do have ebay replacements waiting just in case/when one breaks. Thanks for the video!

Dude front differential is like $200 at any scrap yard,, with low milage.. scraping a jeep for a front diff SMH 😂 .. i know this because a year ago i replaced mine and got one like new with only 70,000 miles on it for $200 , put new seals in it and is perfect…

I have those same brakes on my 67. I like your tire/rim combo, what size wheels/tires do you have?

Did you ever fix this issue? I’m having the same issue and wondering if replacing the driveshaft might fix the noise?

I got this for my civic and it looks huge…. it looks so tiny on your Suv but it does fit a lot!!

Coco melon

Thank you for your help! I had to replace both back interior handles & had no clue until I saw your video...

Oh man, you are speaking my language. I bought the m50 for street stills, but found that even that draws too much attention. I black taped the logos, but here in Montreal people are too hip to the slr form factor. It's tough in this market to source a second hand m200 that doesn't break my bank, but I am ever hopeful (especially since it looks like Canon may scrap the entire M series). Fingers crossed. Cheers from Montreal QC.

You don't need all that just take out the clutch the water pump comes right out