6 жыл бұрын
6 жыл бұрын
Пікірлер
@Allabilitiesoverland Күн бұрын
what do you use as tools to removed the insulation and felt panels?
@ShouldBeGood Күн бұрын
No tools needed to remove the insulation panels. Just need to unscrew the thumb screws and they pull out. Sometimes you need to remove additional panels if they are overlapping.
@MeredithTM1 2 күн бұрын
And no way to charge it..
@ShouldBeGood 2 күн бұрын
Just open in and charge it 👍🏼
@522lobo 3 күн бұрын
Dog in the back just munching on an antler 😂
@KathleenWilson-l6k 4 күн бұрын
This is great information!
@timurich4270 5 күн бұрын
Thank you. I found this video to be very helpful.
@ShouldBeGood 4 күн бұрын
thanks for watching!
@katherinemontoya6133 11 күн бұрын
Could I use without gluing down?
@ShouldBeGood 10 күн бұрын
Yes, it can be used without gluing. It is a very thick and heavy material.
@coreyfuggins2945 15 күн бұрын
How do you charge the battery when it dies?
@ShouldBeGood 15 күн бұрын
@@coreyfuggins2945 just open the box and connect the battery charger 👍🏼
@CVNTGETENOUGH 19 күн бұрын
Would I be able to add a quick connect for charging onto the terminal along with an inverter or are you only allowed one thing connected to the battery terminal at once?
@ShouldBeGood 15 күн бұрын
@@CVNTGETENOUGH shouldn’t have any problems adding a quick connect to the battery terminal. I was thinking about adding an exterior charging port to this one but wanted to keep it simple. Thanks for watching!
@boboEdo 26 күн бұрын
Whats the braker box brand
@ShouldBeGood 26 күн бұрын
It’s GE amzn.to/3VGdUtX
@djkacho Ай бұрын
Dont expect too much from that battery. A small power station with an inverter would have almost 30ah battery inside
@ShouldBeGood 26 күн бұрын
@@djkacho definitely not, the box has room for a larger battery. I just had this 6ah battery for my ice fishing sonar, so it wasn’t being used in the summer. 👍🏼 thanks for watching!
@ricardotorres7053 Ай бұрын
I’m getting great tips from your content, thank you! Please tell me where can I get the hardware or supplies to build my own as well. Keep up the good work! Thanks again!
@ShouldBeGood Ай бұрын
Thanks, glad you're enjoying the videos! Here is a link to the connectors on Amazon amzn.to/4gu4n17 I also order supples from Eagle Aluminum. Good luck on your project! 👍🏼
@dreamlookautodetailingauto3353 Ай бұрын
I love this idea! Do you have a full video on this installation?
@ShouldBeGood 10 күн бұрын
This is the full install video. I just pulled out the stock vent cap from the inside and screwed on the AC vent adapter, its that easy! Thanks for watching
@LatinoCity Ай бұрын
question: where did you get the floor mat and whats it called?
@ShouldBeGood Ай бұрын
@@LatinoCity amzn.to/3D0zxyz I also have a detailed video on the floor install
@TheMikeMartyShow Ай бұрын
Can you provide a link to the 30a inlet box?
@ShouldBeGood Ай бұрын
Hi, here’s the link to the box amzn.to/3ZBRUmc All other supply links are also posted in the video description. Thanks for watching!
@j.t.fchroniclesz1071 Ай бұрын
Just incase next time swap that 90 for a sanitary tee with a clean out.
@ShouldBeGood Ай бұрын
Great idea! I will definitely have to do that on the next one!
@Thechubbypig918 Ай бұрын
Where did you get the roof mount exhaust fan?
@ShouldBeGood Ай бұрын
amzn.to/4fz1A6B
@ShouldBeGood Ай бұрын
Here’s my detailed video on the fan install kzbin.info/www/bejne/rpq7lJtro8qpr5Isi=ty3in4Y2qvf5hyN9
@southern04man Ай бұрын
That ain't gonna work good.
@ShouldBeGood Ай бұрын
Works great! Thanks for watching
@onnie0821 Ай бұрын
Jake, what size are the black screws? Ty
@ShouldBeGood Ай бұрын
Hi Onnie, I am not sure on the size, they come with with window. I would guess #8 x 3/4"
@onnie0821 Ай бұрын
Thank you for the info. One screw is missing and I’m not very handy with these things.
@ShouldBeGood Ай бұрын
@@onnie0821no worries! I’d recommend pulling one out and bringing it with you to the hardware store to match up with one. Good luck on your project and thanks for watching!
@onnie0821 Ай бұрын
@ShouldBeGood, I’m scared to take one out. It might strip the screw. My kind of luck. lol
@onnie0821 Ай бұрын
I pulled one out. Looks like it’s an 8 x 10. I’ll take it to the rv place and get extras.
@mcastellanos657 Ай бұрын
What did you use to install the concession window counter top ?
@ShouldBeGood Ай бұрын
I think I used the hardware that came with the counter
@danpalmer7432 Ай бұрын
Perfect, thank you I like those. we are redoing the inside of cargo trailer for a barbecue food trailer using a similar product instead of ACM. I’m using 6 mm Alumalite® Standard panels over the plywood.
@ShouldBeGood Ай бұрын
Nice! Alumalite is very similar just has a corrugated core instead of solid. It is way more expansive from my supplier though, about 4x a sheet compared to 3mm Alupoly. Thanks for watching and good luck with your build!
@danpalmer7432 Ай бұрын
What did you use for screws?
@ShouldBeGood Ай бұрын
Hi Dan, I used white self tapping lathe screws. Here’s a link amzn.to/3USDQCi
@laurasullivan6690 Ай бұрын
Question for you! I am required to have an air gap between the 3 comp. sink and grey tank. Do you have one? If no, how would you have done this with an air gap? My idea is a floor sink drain but yours looks better.
@laurasullivan6690 Ай бұрын
air gap bottom element minimum 4 inches wide. Grey holding tank external under the trailer, directly under the sinks.
@ShouldBeGood Ай бұрын
@@laurasullivan6690 This system does not have an air gap. I am definitely no plumber but I have seen restaurants with the air gap system and they put it right above the p-trap. So I would just have an open pipe coming from the last drain going into 4" air gap fitting and then attached to the p-trap and down into the grey tank. I would skip installing the air admittance valve since you will have the air gap. Good luck on your project and thanks for watching!
@laurasullivan6690 Ай бұрын
@@ShouldBeGood thanks so much for your reply! Good luck to you as well
@RayenKamta Ай бұрын
How big is the trailer? 6 x 10?
@ShouldBeGood Ай бұрын
Yes, 6x10 with high ceiling. I'd go with atleast a 7x12 on my next one.
@joeL-m7q5m 2 ай бұрын
I wrapped the window opening with home type, flexible window flashing before I sealed and reinstalled the window. I figure that if there was a leak, it would not run down inside the wall. It would either go out or in..
@ShouldBeGood Ай бұрын
That’s a great idea! They should do that from factory!
@RandyWood-j8q 2 ай бұрын
Where did you get the window from?
@RandyWood-j8q 2 ай бұрын
Where did you get the window from?
@ShouldBeGood 2 ай бұрын
@@RandyWood-j8q amzn.to/3kitigj
@RandyWood-j8q 2 ай бұрын
Where did you get the window from?
@ShouldBeGood 2 ай бұрын
@@RandyWood-j8q Amazon amzn.to/3kitigj All supplies are linked in the video description. Good luck on your project!
@michaelhurt4490 2 ай бұрын
Have you welded before? Im tempted to try this but zero welding experience
@ShouldBeGood 2 ай бұрын
@@michaelhurt4490 no, this was my first time welding. I just practiced on the angle iron and adjusted the setting until it looked good. The factory welds on the trailer looked worse than mine so just go for it!
@EricStolp 2 ай бұрын
Hello. Where can I buy the panels. I am here in Fort Worth Texas
@ShouldBeGood 2 ай бұрын
@@EricStolp there is a Piedmont Plastics in Dallas. Reach out to them for some of their Alupoly 3mm panels 👍🏼 Good luck on your project!
@EricStolp 2 ай бұрын
@@ShouldBeGood thank you
@robertrhode6104 2 ай бұрын
Sweet, looks great
@ShouldBeGood 2 ай бұрын
Thanks Robert!
@zachzoladz8673 2 ай бұрын
how much was each sheet for the walls ?
@eddieinta6232 2 ай бұрын
Nice job bro. My consession is on going.
@TheKal619 2 ай бұрын
Great job, I'm thinking of doing a very similar setup. How did you drain the sink?
@ShouldBeGood 2 ай бұрын
@@TheKal619 thanks! it’s connected to a standard garden hose fitting on the outside of the camper. I just run a small hose to a bucket or run it under the truck. Some people install a “grey” water container under the sink.
@lenspin14 3 ай бұрын
well done SBG...best of luck to you and yours!
@CharlieDiloreto-lj6ri 3 ай бұрын
Nice job , Which maxmetal did you use and what was the cost of that product, how do you keep the pipes for freezing underneath?
@ShouldBeGood 2 ай бұрын
@@CharlieDiloreto-lj6ri standard 3mm, I think it was around $45/sheet. I also used Alupoly 3mm from piedmont plastics. The grey water is drained after every event so it doesn’t have time to freeze. The interior water heater and lines have to be blown out if it’s stored without heat in the winter.
@francescosorrentino1559 3 ай бұрын
@shouldbegood I see that you are using under the trailer tank and a inside one too .. could you use both under the trailer to leave room inside the trailer? If I buy both for under???
@ShouldBeGood 3 ай бұрын
You definitely could, most travel trailers have the fresh, grey, and black tanks underneath. However, installing on the inside makes it easy to check the level and made installation a lot easier. Good luck on your build!
@francescosorrentino1559 3 ай бұрын
@@ShouldBeGood and I could use 2 black tanks like this one Or fresh water has to be white?
@ShouldBeGood 3 ай бұрын
@@francescosorrentino1559 I don’t think so, the fresh water tanks are all this milky white color and are approved for potable water.
@francescosorrentino1559 3 ай бұрын
@@ShouldBeGood figured.. need too see how to install those under the trailer since they have a different shape …
@1LyonsDen 2 ай бұрын
Thank you for this video! what size is the hole saw bit and brand?
@blendandbloom1 3 ай бұрын
Very Nice! What is the interior height?
@ShouldBeGood 3 ай бұрын
6’4” Thanks for watching!
@Gary-f2j 3 ай бұрын
What state do you live in. I see a ventless water heater?
@ShouldBeGood 3 ай бұрын
CO
@jimsteele7108 3 ай бұрын
That’s a great idea. I bet it helps with gas mileage.
@ShouldBeGood 3 ай бұрын
Links for Parts: Battery amzn.to/4d3a5Vt Power Inverter amzn.to/4dZi32Z Box amzn.to/4dkJdAB Mounting Tape amzn.to/3Tr5iX1 This simple power station has space to add a larger battery or carry your charging cables or accessories, making it easy to pack. It has many uses but I use it to power tent lights, fan, sound machine, and charge our phones while camping with the family.
@KirbyChapo 3 ай бұрын
first off, good job man it looks really good! videos like this really inspire me, im currently building my own food sale trailer out from scratch and im using pretty much everything that was recycled and from what i can find. I want to know how much those wall and ceiling panels were and what their called, what material or supply did you use for the flooring and price if possible. also for the sink and all that may i get a list of what you got and possible a quote of how much they were. and on your electrical work, nice job. what amp will you be running and the prices on the hardware that was used to build it. again appreciate the video. i hope to post my videos and pictures soon when im done with it.
@ShouldBeGood 3 ай бұрын
Hi Kirby, thanks for the kind words! I created an entire playlist that has detailed videos for each part of this build with links to all products used. The panels are 3mm ACM Alupoly and were about $45/ea from piedmont plastics when I built this. Here’s a link to my playlist kzbin.info/aero/PLI5tuDJRztZLdoa4ZZDGlBV8dvlfRgjFy&si=LonnNVX-bGtHCs2o Good luck on your project!
@mikesbackyardbarbecue 3 ай бұрын
What pipe did you use for the vent pipe? Thanks
@ShouldBeGood 3 ай бұрын
1/2” abs
@mikesbackyardbarbecue 3 ай бұрын
@@ShouldBeGood Thanks... Unfortunately, I can not find any 1/2 ABS pipe, so I'm going to have to go with PVC or pex pipe. But great video!
@ShouldBeGood 3 ай бұрын
@@mikesbackyardbarbecue yeah that should work just the same. Thanks for watching and good luck on your project!
@mikesbackyardbarbecue 3 ай бұрын
@@ShouldBeGood Quick question. On the 1-1/2 Rubber Tank Grommet - does the PVC drain pipe go past the little rubber lip at the back of the grommet or is the drain pipe supposed to stop at the lip preventing it from going into the tank further? Thanks
@ShouldBeGood 3 ай бұрын
@@mikesbackyardbarbecue yes, it is designed to stop the pipe from going in too far
@BKAD623-hz7ln 3 ай бұрын
I have one in my cargo trailer. Been using it four years full time works great. ✌️
@kevin.campbell 4 ай бұрын
you lost so much capacity by putting the inlet on the side
@ShouldBeGood 3 ай бұрын
Actually didn’t lose any capacity with a side inlet. The only negative would be a reduction in flow rate if the water level gets above the inlet. However, since the tank is oversized by 15% from my freshwater tank this will never happen.
@KaySancoppermug 4 ай бұрын
Thx for the video .
@ShouldBeGood 4 ай бұрын
Thanks for watching and good luck on your project!
@ATOMICHOLLYWOOD 4 ай бұрын
Thank You for the great Quality and infornation Video. May i ask what it cost you to buy all panel s to complete the inside walls ? Thanks Chris.
@ShouldBeGood 4 ай бұрын
At the time I think I paid $45 per panel. Thanks for watching!
@Jason-crypto 4 ай бұрын
What size dimensions is the grey water tank so that both fresh and grey fit under sink?
@ShouldBeGood 4 ай бұрын
I didn’t install my grey water under the sink, only freshwater.
@LucasCopeland-z9g 4 ай бұрын
How has the PVC trim held up? I just put my order in for my white 3mil panels and am debating between your solution or aluminum divider trim from Orange Aluminum.
@ShouldBeGood 4 ай бұрын
It’s held up great on the walls, but a couple spots on the ceiling have pulled away but not bad. I planned on using panel dividers but it was a major pain during install because my panels fit so tight from floor to ceiling. Doing it over I would cut the panels shorter and use a bigger top corner trim.
@TheAdymiller 4 ай бұрын
Kimbo needs to make travel trailers and toy haulers.
@ShouldBeGood 4 ай бұрын
@@TheAdymiller I agree!
@lifeandTrucking 4 ай бұрын
So wish it was more detailed. Like the screws, the little stuff.
@ShouldBeGood 4 ай бұрын
The screws I used are linked in the description 👍🏼 thanks for watching and good luck on your project!