DIY Plumbing 3 Compartment Sink & Hand Wash Sink Drains Food Trailer - CTC Ep.11

[@lenspin14]

well done SBG...best of luck to you and yours!

[@j.t.fchroniclesz1071]

Just incase next time swap that 90 for a sanitary tee with a clean out.

[@ShouldBeGood]

Great idea! I will definitely have to do that on the next one!

[@brianc3481]

Good work, hopefully that works flawlessly.. aavs are the best for stuff like that

[@jamesguiberteau6607]

😂 should be good. Lived by this philosophy all my life and i guess i turned out "good"

[@ShouldBeGood]

it's a proven method 😂 Thanks for watching!

[@laurasullivan6690]

Question for you! I am required to have an air gap between the 3 comp. sink and grey tank. Do you have one? If no, how would you have done this with an air gap? My idea is a floor sink drain but yours looks better.

[@laurasullivan6690]

air gap bottom element minimum 4 inches wide. Grey holding tank external under the trailer, directly under the sinks.

[@ShouldBeGood]

@@laurasullivan6690 This system does not have an air gap. I am definitely no plumber but I have seen restaurants with the air gap system and they put it right above the p-trap. So I would just have an open pipe coming from the last drain going into 4" air gap fitting and then attached to the p-trap and down into the grey tank. I would skip installing the air admittance valve since you will have the air gap. Good luck on your project and thanks for watching!

[@laurasullivan6690]

@@ShouldBeGood thanks so much for your reply! Good luck to you as well

[@chrisheiberger3685]

Nice video, this was exactly what I was looking for, as I'm doing the same set-up in a small bar area.

[@ShouldBeGood]

Thanks for watching and good luck on your project!

[@A1DeliandSmoke]

So to become certified by the New York state you can use pvc?

[@KaySancoppermug]

Thx for the video .

[@ShouldBeGood]

Thanks for watching and good luck on your project!

[@velascofrancisco79]

Si I made one like it thanks to you

[@prid1234]

Since you installed a p trap with no union, how is one supposed to service this and take it apart without cutting everything out? Also would recommend a cleanout on the vertical drain before it goes through the floor.

[@ShouldBeGood]

The p trap I installed has a drain plug for servicing and the vertical pipe has an air admittance valve that can be removed to clear any clogs. Should be good 👍🏼

[@larrywilliams4816]

where are your paper gaskets?

[@ShouldBeGood]

@@larrywilliams4816 I don’t use the friction gaskets, just lubricate the rubber gasket and the locknut tightens right up. Thanks for watching!

[@MichaelZerai]

Thank you so for your help Can you help me for the leg of the sink mount to the trailer what size mount you use

[@ShouldBeGood]

1 5/8" Here is what I used amzn.to/3Wne7U2

[@MichaelZerai]

@@ShouldBeGood thank you again be bless more and more

[@juanbeltran7696]

Any video how insulating wall for trailer

[@ShouldBeGood]

No, I just cut 1” foam insulation to fit between the framing

[@Gary-f2j]

What state do you live in. I see a ventless water heater?

[@ShouldBeGood]

CO

[@Jason-crypto]

What size dimensions is the grey water tank so that both fresh and grey fit under sink?

[@ShouldBeGood]

I didn’t install my grey water under the sink, only freshwater.

[@scottfung7700]

The p-trap is used to block off sewer gas. However, your vent pipe, which carries sewer gas, ends under the sink's drain board. What is the point of installing a p-trap then?🤔🤔

[@ShouldBeGood]

Hi Scott, that is not the vent under the drain board. It is an air admittance valve, which only lets air into the pipes to increase drain flow and prevent negative pressure to further prevent gasses from coming back up through the pipes. The gray tank is vented on the outside of the trailer. Thanks for watching!

[@derekmitt23]

I think that sanitary T is supposed to be a wye fitting. Looks good other than that.👍

[@erickt3960]

What size 3 sink is that?

[@ShouldBeGood]

It’s 54” total width. amzn.to/3ZcfHX6