Install Interior Wall Panels for Food Trailer - Aluminum Composite! | Cargo Trailer Conversion Ep.5

[@Sugarcakeco]

You just gave me life with these videos! Looks like this is actually doable. Thank you for sharing 😊

[@ShouldBeGood]

It’s a lot of work but if I can do it, anyone can! Thanks for watching!

[@jonphillips1638]

dude . THANK YOU !! hours of white panel searching .. INSANE !!!

[@ShouldBeGood]

Thanks for watching and good luck on your project!

[@CourtneyUglow]

How did you trim out the metal after application? Thanks in advance for your advice and help.

[@MoparCrazy803]

2 months of researching wall panels with no luck. Came to your channel and bam it's a Piedmont Plastics 2 exits up from me. Thanks man I really appreciate it.

[@ShouldBeGood]

@@MoparCrazy803 Can’t beat that! They are such a great resource and have many options in their Alupoly ACM. Thanks for watching and good luck on your build!

[@MoparCrazy803]

@@ShouldBeGood Absolutely. Now it's just explaining to my wife that I can't build a food trailer in 2 weeks lol. Thanks for the help buddy.

[@ATOMICHOLLYWOOD]

Thank You for the great Quality and infornation Video. May i ask what it cost you to buy all panel s to complete the inside walls ? Thanks Chris.

[@ShouldBeGood]

At the time I think I paid $45 per panel. Thanks for watching!

[@CourtneyUglow]

What type of screws did you use to attach the panels to the walls and ceilings and size please.

[@ShouldBeGood]

Hi @CourtneyUglow I used white lathe screws 3/4” to attached the panels and used pvc edge banding to cover the seams. amzn.to/46iODc5

[@zachzoladz8673]

how much was each sheet for the walls ?

[@valentinsalas8300]

What trim did you used for the top that connects to the side walls

[@ShouldBeGood]

I used 1"x1" angle aluminum from trim on the top and bottom of the walls. If i did this again I would use the stock .040 aluminum that trailer manufacturers use though and cut my walls about 2" shorter so I would have easier access for the wiring.

[@CourtneyUglow]

Sorry I should have been more specific, what type of trim did you use on the ceiling seams?

[@LucasCopeland-z9g]

How has the PVC trim held up? I just put my order in for my white 3mil panels and am debating between your solution or aluminum divider trim from Orange Aluminum.

[@ShouldBeGood]

It’s held up great on the walls, but a couple spots on the ceiling have pulled away but not bad. I planned on using panel dividers but it was a major pain during install because my panels fit so tight from floor to ceiling. Doing it over I would cut the panels shorter and use a bigger top corner trim.

[@dsep6770]

Did you use this SKU number of panels material that you’re using because I went to the website and I found this one they don’t have the all white on both side the number I found was SKU: MM843MMS, 4 x 8 Mirrored Silver / White is this the one you use

[@ShouldBeGood]

SKU: MM843MWLT, 4 ' x 8 '. Max Metal Lite. I’ve switched to Alupoly for all my ACM material though, it’s better quality and less expensive. www.piedmontplastics.com/resources/literatures/piedmont-sign-gradeR-alupolyR

[@ROBERTLUCIAn]

What screws did you use to attach the panels? Also what trim where two panels but together? I watched a few of the videos and can't figure those out. Thank you.

[@ShouldBeGood]

I used white lathe screws to attached the panels and used pvc edge banding to cover the seams. amzn.to/46iODc5

[@kyleedugger]

@ShouldBeGood This PCV tape makes sense for the laps. Its quite genious actually. What about the corners (90 degrees)?@@ShouldBeGood EDIT: I think, I see you bend the pieces for angles, so you didn't have any corners only laps. Nice idea.

[@anthonyhogan3345]

Did you insulate the walls on this project?

[@ShouldBeGood]

Yes, I insulated all walls and the ceiling. 1” foam insulation works great.

[@primevideoscreateor]

What size panel my trailer is 20x8.5

[@ShouldBeGood]

how tall are the interior walls? I used 4'x8' panels

[@acostaedwin986]

What type of plywood do you use on the walls?

[@ShouldBeGood]

I just put back up the plywood from the factory. I think it was 1/4”

[@acostaedwin986]

​@@ShouldBeGoodthanks

[@ronaldfontenot1897]

What is the name of wall material

[@ShouldBeGood]

Hi Ronald, the wall panel is 3mm ACM. (Aluminum Composite Material) There are many different brand names and most plastic and metal supply companies stock it. Polycor, Alupoly, dibond, e-panel, maxmetal, alucobond are some of the brand names.

[@wrxzboost]

@@ShouldBeGood these are the best solution i've seen for trailer panelling. which size did you go with? i have a 6x10 trailer so trying to limit the seams.