Thank you for the info! Got a broody Orpington right now needing a bath.
@brianlogue868013 күн бұрын
Memories 😅
@951media18 күн бұрын
A for effort. The other Tacoma bros with lift and 35/ should try like you.
@wyattames565920 күн бұрын
if u went with a locker in the rear what did u go with? starting my build watching these videos lol
@samuelc690421 күн бұрын
Why in the hell are all the sbc turbo builds no intercooled lol
@2shoestooАй бұрын
What gear ratio did you change too to pull those big A tires
@invisableobserverАй бұрын
enjoyed the camshaft story & music
@invisableobserverАй бұрын
Got ya a poon wagon. You can also use those exhaust studs to mount the knock sensors on the outside of the heads, so they last longer plus you wouldn't have to pull the intake off to replace them.
@invisableobserverАй бұрын
Do the drum brakes still stop it? I'd like to do the low AC & that water pump & a few other things on my swapped '65 C10. If you was closer I'd pay you to work on mine, but by your CA tags your too far away
@quintonahmad20Ай бұрын
How much did the drive shaft shorten or leg then going from the stock trans to the 4l60e
@MrGritboyweirАй бұрын
Hey did you ever figure out a solution for the Dust shield? I just did this swap but can't find a dust shielf that works
@netomtb9699Ай бұрын
Size and type of tubing???
@EvanReubАй бұрын
Do you have a link to the throttle cable you used?
@donhappel95662 ай бұрын
A bit late here but YT only just served this up. I believe an experienced driver in the AEV or even ZR2 Colorado could readily make it to the bowl. The others...not so sure.
@johnnyrebel33402 ай бұрын
Did your taco have a little locking rear diff?
@user-ji7ty4ny3l2 ай бұрын
What bumper and winch do you have on that puppy.
@arthurianwilliams50452 ай бұрын
Question...a drawing of what you did..in sections...who be very nice....showing all parts , diagram..on wiring each part up......
@franciskovaldovinos24092 ай бұрын
Nice work. How you get the ac compressor wired into the ls pcm and cooling fans? Please advise
@spicoli97972 ай бұрын
2 inch Body left Would have been fairly cheap and helped out the situation a lot, I would still do it It would look a hell of a lot better too
@petehoefs26192 ай бұрын
I like the way you got the trans on the jack
@robertogarcia352 ай бұрын
excellent and dirty job but you need 4 hands for this I want to do the same on my 2000 4runner
@700horses2 ай бұрын
Awesome build. Awesome video.
@danielalfaro49333 ай бұрын
Clean work
@christandinewmachinesaerze98183 ай бұрын
Hi! Was it flux core or gas mig?
@collingraley51473 ай бұрын
DOC OFF-ROAD for skids!! Go check'em out!
@basemandog3 ай бұрын
So clean. I am currently struggling with a wiring nightmare on my LS swap
@ClassyTacos3 ай бұрын
Man that was awesome. I need some fire pit therapy soon.
@Clay5243 ай бұрын
Hi! I’m doing a 1972 K10 LS swap What do I do with the gauge cluster? Is it possible to have a working speedometer and do the sell gauge clusters for this purpose? Thank you, Bill
@user-el1qr1mv3g4 ай бұрын
hey would you be willing to bend up a kitand ship? ill pay
@robertbanks68704 ай бұрын
Ho much 700r4 transmission $?
@tommymccabe96784 ай бұрын
What did you use for those turn signals?! Sweet build!
@pmotorsports82764 ай бұрын
Sniper has a tps mounted on side you can tap into. Let me kno when you work on a project. I can sale you some parts you don't need
@pmotorsports82764 ай бұрын
The sbc's crankshaft sticks out .040 " so now you have .080" of space. Should be titled how to throw away money. Extra money for controller fab time. If your going electronic go 4L80E
@BadDad4204 ай бұрын
like how he went hard first. He inspired me to give this a try
@pmotorsports82764 ай бұрын
Link to headers
@pmotorsports82764 ай бұрын
Alot of work for 1/2 ton transmission
@pmotorsports82764 ай бұрын
If you're going electronic just go 4L80E = real transmission
@pmotorsports82764 ай бұрын
Why just use 96-99 298mm input
@DavidAyala-rc7zv4 ай бұрын
Where in Cali?
@Chobham4 ай бұрын
Which trim 4Runner is it?
@maneeoocho3504 ай бұрын
Is the 3rd gen still running?
@dieselapegarage4 ай бұрын
Looking good in there nice keep it coming gotta keep the old school chevy classics alive keep it coming 👀 🍿
@matthewtwright845 ай бұрын
This hurt so much to watch but I couldn't look away
@jonathanfelix20405 ай бұрын
Do you have videos on how to regear?
@Rhouzv5 ай бұрын
What lift are you running? Did I miss you mentioning that? Offset to wheels? I bought a 3rd gen that “needed a new motor” and it ended up being a MAF and knock sensor. Got $1500 in it and absolutely want to go this route to keep it “cheaper” lol
@timberlineoffroad5 ай бұрын
Any adventure in the mountains is a good day, love it!!
@timberlineoffroad5 ай бұрын
Duuude! Awesome wheeling the new rig!! Its good to wheel in stock form before you build it so you can compare before and after!👌👌👌💯💯
@timberlineoffroad5 ай бұрын
Super awesome! Congrats on the new baby!!!
@marksetters9316 ай бұрын
Congrats on the birth of your son! Great to see you back at it.