Yes, I would like a couple of dozen of these please... 💸 💰

Super legit! How do you like that Bamboo printer?

were you able to fix the battery issue? video ended

Can you please help me, when changing 2 AO Smith filters, after replacing the filter one leak water. How can I fix that problem?

" I will publish the code and link it here shortly."

I’m sure you get a ton of head turns.

Cool car!

Nice build! Let’s take it for a drive

I had that issue but it was just my throttle trim and the esc was just trying to protect me from an accident

How is the car doing now? I have heard the ultimate solution is to replace the whole pack. Changing just a module usually does not last long.

I was really hoping to see how hard it is to peel off the lid.

Hey so was it one of the modules in the penthouse that needed to be replaced? You show how you lowered the pack and opened the penthouse but nothign more. I was curious to know what you did to fix your BMS_018 code

So.... no repairable.... fuck What an incredible amounts of E-Waste this is

Hi! Sorry I'm bringing up an old post. Could you figure out the wiring diagram? Thanks!

Thank you for the update video! You helped me fix mine. I read about the "push the button 7 times" fix, and that didnt work for me. It wasnt until you mentioned it being stuck and you fiddling with it that i really manhandled it and got it to work. Thank you!

Just got mine a week ago and loved the simplicity, but this is shocking! I hope Bambu can investigate this and make improvements soon.

arn't they supposed to detect fails? if so this is a huge fail on Bambu.

Buy a new one.....

Any chance i can buy the tool?

When I enter service mode my screen doesn’t look like this, can you show how you got there?

I just did this. First the cartridge leaked around the o-ring closure that encloses the filter. I had to loosen it a little to make it stop leaking. Then once the first stopped leaking the second one started so I did the same thing. Then once I had them both not leaking there was no flow at all! I had to loosen the cartridge to unit connection a tiny bit and it all of a sudden had great flow and kicked out a lot of trapped air and now it's all working and not leaking. I guess the moral of the story is to loosen up a little 😂 I guess you just have to really rely on those orings because of the cheapo plastic threads.

You can use we chat ?

There is no point of this video.

No good!

You have to rub the pod part in the middle at the top. It’s a KZbin video about this. I had the same problem after my son bought it now mine works fine now.

POWER 🏆

I’m not sure I have ever smelled lithium. Maybe we need some sort of a sample smell so that we can learn from it

Awesome video. As more and more of these packs fail, hopefully the knowledge required to fix them yourself spreads, and the nonsense of $20k repair bills can be killed. Good job!!!

Any code available for your Dial projects?

I'm having the same issue with my system as well. Just put in two new filter replacements and not getting any water flow out of the system. If I slightly loosen up the two stages, water will start to flow.. but it will also start to leak at that point as well. Not sure why this is such an issue. I'll try calling AO Smith and see if they can offer any helpful advice.

Awesome!

I'm super grateful for this video - couldn't figure it out and was on the tire pressure screen

You can try disconnecting the 12 volt for a bit and see if it will charge up. The 12 volt runs the computer so it can forget or reset like a lot of cars. Electrified garage can fix it, or Grubers.

y si en vez de colocar un usb quisiera colocar una carpeta en red como lo hariamos?

Hey did you ever get it working?

Some people suspect it's an air blockage problem but i am not sure. I would try to fill the two chambers with as much water and try again. (or try to dry all water). One thing you might want to do every time is keep the faucet open when turning the "pressure" on.

What is price.

Super helpful bro

Iam looking for Zeva Bms but i can't find, can you help me

Iam looking for zeva car conversion kit but I can't find any thing

I just bought the same coffee maker today and was having trouble shooting it l I will try the black rubber button method thanks for the video !

Hello, on wich pins do you give power so that the controller goes on? In the documentary is a connection between 1 and 6 (key switch in) but there is no power input to find.

Bms_a64 on teslam3md

There is only Alexa as a voice command?

kzbin.info/www/bejne/Y3ynmXV_gNutoZIsi=Xu1a5Ef43_J3EI4u

If you will toggle the little black rubber button under the pod opening it will make the light come on and work. I got it from another idea and will link it if I find it.

Awesome

Hi What is the device you are using to read the module parameters?

kzbin.info/www/bejne/Y3ynmXV_gNutoZIsi=wVpOez-uubOtNUDV

An electric motor is an electric motor. There are DC motors & AC motors. Study electric motors & you will learn where the wires go. One of them has to be the ground or neutral, usually, it is visibly different than the others. Fatter maybe. the cables go to motor windings mayhaps there is low speed winding, a mid speed winding and a high speed winding. Is this motor equipt with dynamic braking? There will be cables for that too. There are 1phase motors, 2 phase motors, 3 phase motors. See if this might help>>> kzbin.info/www/bejne/oH-aoGquq7RphsU !