Take note: The carpenter bee channel is never straight into the wood. They will burrow in about 1/2 - 3/4 of an inch and then make a 90 degree turn. So the channel will be along the front of the wood not directly straight into the wood. If you are going to spray insecticide into the channel, make sure your "straw" goes off to the left or the right before you spray. Spraying directly into the hole will do nothing but waist expensive chemical onto the ground.
@thehousemannСағат бұрын
good to know
@1Love-starboss7 сағат бұрын
Is That a google pixel
@thehousemann7 сағат бұрын
@@1Love-starboss yep. P6
@ThePrabhu16Күн бұрын
FAKE VIDEO WASTING EVERY ONE TIME. don't waste your time. macros don't work in this worst logitech. as no ghub software installation allowed in my company laptop i need onboard for macros. THROW THIS LOGITECH SHIT IN DUSTBIN and go for razer mouse, you can directly do any kind of key hits easily onboard.
@ohplezz3 күн бұрын
Thank you for the instructions. I’ve got a 22 club model and I got the blower motor replaced under warranty at 35k miles in April. Now, 4 months later at 40k miles, the blower motor is fluctuating its speed again in a system that does not have a thermostat set point like the way the GT models do. By chance do you know if these blower motors are just defective? Does anyone know if they have a TSB out for them? Regardless, thank you for the instructions. They are really straightforward and easy to understand.
@thehousemann3 күн бұрын
Sounds like either a voltage issue or the motor is failing which unfortunately is a common issue.
@ClamBow10 күн бұрын
None of your things in the video helped. I fixed it my self by thinking smart. I removed Google. And reinstalled it. Then it wanted me to setup google assistant again. After that i can now hear the google again.
@thehousemann10 күн бұрын
@@ClamBow good to know.
@ClamBow10 күн бұрын
@thehousemann I think for android 13. When the newest Update came out it broke google
@jooniee85811 күн бұрын
Great tutorial, thanks! Question from my end. I notice that with yours, when you change the profiles, the 3 lgihts on the side of the mouse change from 1, 2 then 3 depending on profiles. Mine for some reason is keeping on 2 out of 3 lights on and when I change profiles, it doesn't change. Is there a way I can configure this?
@thehousemann11 күн бұрын
Go into your light settings page. Should be an option there to change the behavior of the side lights. Mine will cycle to show which profile is being selected and then switch to show which dpi setting I have it on
@micsnz12 күн бұрын
Where's the other ram slot located? How come there's only one slot?
@thehousemann12 күн бұрын
@@micsnz only one slot is upgradable. The other is soldered on.
@JoshuaWestbrook-t3o12 күн бұрын
First comment ever: THANK YOU!
@thehousemann12 күн бұрын
@@JoshuaWestbrook-t3o You're welcome!
@jettschenker13 күн бұрын
Doesn't rapid charging of any battery diminish the overall life of a battery?
@thehousemann13 күн бұрын
@@jettschenker not with modern batteries.
@DavidMartinez-yi8kz14 күн бұрын
If it’s too high. How do we lower it back down?
@thehousemann14 күн бұрын
@@DavidMartinez-yi8kz from what I remember. You pull on the circle collar on the inside of the base to release the cord
@XxGoUcHiExX116 күн бұрын
Great video thanks
@thehousemann16 күн бұрын
You're welcome
@Attictrash117 күн бұрын
Every time I say hey google, it opens the Google app instead of the Google assistant, is there a fix for this?
@thehousemann17 күн бұрын
@@Attictrash1 You just need to change your language. Make sure it's set to a specific region like English (US) not just English and that should solve the issue
@xaratyniz22 күн бұрын
Great! Off the bat I opened it thanks budd
@thehousemann22 күн бұрын
@@xaratyniz you're welcome!
@absdab567423 күн бұрын
still didnt work for me
@thehousemann20 күн бұрын
:(
@abo-_-najim549725 күн бұрын
It didn’t work 😢 ☹️
@thehousemann24 күн бұрын
sorry :(
@kimberlyg732325 күн бұрын
Brilliant! This worked fantastically to fixed our sofa! Thank you so much!
@thehousemann25 күн бұрын
@@kimberlyg7323 love to hear it!
@ericsimms272726 күн бұрын
Thanks for the help..!!! Appreciate it.
@thehousemann26 күн бұрын
Glad to be of help!
@elijahbillings465827 күн бұрын
This worked for me. Thank you!!!
@thehousemann27 күн бұрын
Awesome! Glad it helped!
@shivanshpandey501829 күн бұрын
Thanx buddy...it was helpful 😊
@thehousemann29 күн бұрын
@@shivanshpandey5018 glad it worked for you
@jaywalk688329 күн бұрын
accessing the mic to either turn on or off does have capability to do either, what to do?
@thehousemann29 күн бұрын
Check your permissions for the app and check to make sure you have "always allow microphone"
@jaywalk688329 күн бұрын
I accessed activate mic according to instructions because the mic showed not working but after the feature to turn on or off shows, it is blank and do not have ability to either turn on or off. What to do?
@thehousemann29 күн бұрын
@@jaywalk6883 try uninstalling and re-downloading the Google app
@JaeMjaeriskАй бұрын
Worked for me thank you
@thehousemannАй бұрын
@@JaeMjaerisk glad to hear it!
@mydevice4027Ай бұрын
shitty software, cant even save double click in onboard memory
@thehousemannАй бұрын
🤷🏻♂️
@SpazTheGamerАй бұрын
What size string is good?
@thehousemannАй бұрын
.080
@PeterHuang1113Ай бұрын
can you cut horizontally? for example, if I want to cut some bamboo cane to ground?
@thehousemannАй бұрын
Yea I've cut plenty horizontally. The head won't turn, but just move your wrist 90 degrees..
@PeterHuang1113Ай бұрын
@@thehousemann thanks for the replay!
@juansandoval8737Ай бұрын
Can I turn on a 5 gallon air compressor
@thehousemannАй бұрын
How many Amps is the compressor? That's what the question is. You'll be able to run it, but might be a heavy load if ran for too long
@cartoonnetworksarea.Ай бұрын
When I long press the home button, it takes me to google how can I avoid hhat
@thehousemann29 күн бұрын
Do you mean the Google home page? The Google one page? Or the Google voice pop up?
@thehousemann29 күн бұрын
Depending on your phone it could be different. On mine, you'd want to goto settings - gestures - power button hold - and change what you'd like it to do from there.
@cartoonnetworksarea.29 күн бұрын
@@thehousemann I use an a24 and it's up to date
@dorianpenalozaАй бұрын
I installed one and similar to you video, the mount is not flush to the ceiling. How do you fix the gap between the mounting bracket and the ceiling.
@thehousemannАй бұрын
I left the gap and honestly never notice it. You could use some Chaulk to fill in the gap if it really bothers you.
@sj460162Ай бұрын
Thanks bud I will try it. It works..I love you!!
@thehousemannАй бұрын
@@sj460162 hope it works
@RimWulfАй бұрын
That didn't help at all
@thehousemannАй бұрын
@@RimWulf sorry, it's not guaranteed to work for everyone.
@snutpclan6386Ай бұрын
tengo ese esmeril, con que batería me recomiendas usarlo ?
@thehousemannАй бұрын
Depende cuanto lo vas a usar. Una de 4ah sería un buen balance.
@twilightfreak16Ай бұрын
Can anybody please tell me if it works on carpets? I have apartment carpets with similar texture. 😢
@thehousemannАй бұрын
It should but with a larger needle. But carpet usually isn't a interwoven piece of farbric like this? Even low ply carpet would be really short strands.
@EchoRider515Ай бұрын
🤗 Oh Thank You! I've been trying for weeks to resolve this. Sure wish I'd have seen Your video before the MANY I've watched which were of no use at all. I have zero tech savvy. You, sir, have a new subscriber.
@thehousemannАй бұрын
I'm glad to hear that! If I can help someone anywhere along the way then my job is done ❤️
@EchoRider515Ай бұрын
😁👍@@thehousemann
@tedomalleyАй бұрын
Absolutely Excellent Tutorial! This morning, I installed the ACC IG Controller, ND Window Controller, RF Roof Controller, and Fuse Relocator mods -- all four took only 32 minutes thanks to these vids. I watched each video and read through the instructions a couple of times and then couldn't believe how fast it went. I wasn't even hurrying. I'm pretty certain I could do all four in 20 minutes or less, next time!
@thehousemannАй бұрын
I'm glad to hear and love that my sacrifice made it quick and easy for you. I think between trying to figure it out and getting it all on video this took me almost 4 hours to do 😅
@tedomalleyАй бұрын
Absolutely Excellent Tutorial! This morning, I installed the ACC IG Controller, ND Window Controller, RF Roof Controller, and Fuse Relocator mods -- all four took only 32 minutes thanks to these vids. I watched each video and read through the instructions a couple of times and then couldn't believe how fast it went. I wasn't even hurrying. I'm pretty certain I could do all four in 20 minutes or less, next time!
@thehousemannАй бұрын
Excellent!
@dorianjimenaruto9772Ай бұрын
I love you
@thehousemannАй бұрын
ILU2❤
@allenfullerton6693Ай бұрын
Your video was quick and to the point good job
@thehousemannАй бұрын
thank you!
@vidtoddАй бұрын
Thanks! It is the easiest strange string installation.
@thehousemannАй бұрын
@@vidtodd nice!
@HuntersCyclingAdventuresАй бұрын
I wish you could plug it in to charge while the battery is in the fan and running definitely doesn’t last long on high
@thehousemannАй бұрын
Yea that would be nice.
@user-bl1sk2ix2kАй бұрын
Thank you!
@thehousemannАй бұрын
You're welcome!
@marktwo3160Ай бұрын
I think i would have done a function test before putting it all back together first.
@thehousemannАй бұрын
😂 Not a bad idea
@jeanayrtonmichael9742Ай бұрын
Salut, pour remplacer la batterie.....faut il la valise ? Je veux dire est-ce qu'il ne faut pas passer chez le concessionnaire pour réinitialiser les données du tableau de bord ? Merci d'avance pour votre réponse !!!!
@thehousemannАй бұрын
Désolé, je ne parle pas français, donc je ne comprends pas bien la question (en utilisant un traducteur). Vous devriez pouvoir changer la batterie sans aucun problème. Toutes les données du véhicule sont stockées sur l'ordinateur de bord. J'ai seulement entendu parler de paramètres réinitialisés si la batterie est déconnectée trop longtemps.
@jeanayrtonmichael9742Ай бұрын
@@thehousemann OK, super, vous avez répondu favorablement à ma question !!!¡ merci à vous !!!!!!
@sarahparsons7925Ай бұрын
There is an easier way to get traction in order to remove the blade. There’s a slit under the blade and if you line it up with the slit in the blade rotating part, put a Phillips screwdriver in there, it locks it up and there’s zero rotation. Sorry for the not having the correct names but you can find it if you turn the edger sideways a bit.
@thehousemannАй бұрын
Oh damn. You're right! Just checked mine. I'll have to make an updated video for the next time I replace the blade.
@infotechsailorАй бұрын
Flathead screwdriver works better than a Phillips
@jovs17Ай бұрын
Me now: Ordering felting needle. I hope it will work.
@thehousemannАй бұрын
It should!
@Mangled1060Ай бұрын
thank you so much
@thehousemannАй бұрын
@@Mangled1060 you're welcome!
@sekritskworl-sekrit_studiosАй бұрын
Is measurement from front or rear of the unit?
@thehousemannАй бұрын
It's from the rear, and doesn't start registering until 5in minimum
@sekritskworl-sekrit_studiosАй бұрын
@@thehousemann Thank you.
@Troy_Sent_A_MessageАй бұрын
Mtd figured out your hack and raised prices :( O well bidenomics at work
@thehousemannАй бұрын
"inflation" 🤦🏻♂️
@Jdigital345Ай бұрын
I bought this saw, very detailed video with one massive difference to the one that arrived, the harbour bolt on mine was unbelievably over tightened from factory (I am a mechanical engineer of 30 years so knew it was a left handed thread) on trying to undo the bolt with a longer Allan key than the one supplied it suddenly give way causing my shoulder to jar. After a visit to A&E and an MRI scan I was told I had severed 2 of the tendons in my rotator cuff. 😢😢😢😢
@thehousemannАй бұрын
Oh lordy that's never good. Sorry that happened to you. Wishing you a speedy recovery.
@bobn2805Ай бұрын
Wish I could do this with my 2024 model 😢 Asus decided to solder all of it
@thehousemannАй бұрын
Damn did they? Didn't know. I was debating the 24 for the oled. But snagged the 23 for a great price. The 16gb does decent, but i edit all my videos on it so the extra ram has been nice.
@bobn2805Ай бұрын
@thehousemann yeah I have 32gb since I have the 4070 version but I wish I could get more. At least it's fast ram
@thehousemannАй бұрын
@@bobn2805 from what i was reading, at least with the 23s, was that the system didnt really like having more than 32 gb. you'd essentially bottle neck ourself going anything larger than a matching 16gb stick. Not sure if thats also the case on the 24s, so you might not actually be missing out on much if you already have 32gb
@pizzacat369Ай бұрын
If you have the 2024 model just buy a soldering kit
@thehousemannАй бұрын
@@pizzacat369 Yea but how many people are going to be comfortable taking a soddering iron to their new laptop.
@ropestanАй бұрын
Seems like G502 x can save macros that only press keyboard keys and are not on repeat to the onboard memory. E.g. autoclicker that is set to press MOUSE1 with 50 ms intervals will not work and that type of macro is also flagged as not supported in logitech onboard memory manager program. This kind of ínformation should be readily available at logitech's websites instead of us fucking around with the software to find out.
@thehousemannАй бұрын
I agree. With a notice that more than half of the onboard profiles don't work.