Looks awesome! I'm trying to find a front fairing for my 3. gen, but haven't found any. Do you know where to look?

Superb video clear step by step. Cheers

Good man!

Exceptional how to video!

This pace is very very slow.

Why not just buy the trophy bike…?

Nice video brother. Having the same problem but I have 23k miles on the bike and it just started to happen do you think I could take off the oil filter without fully draining the bike? How much oil do you think I’ll lose.

Easy peasy ! Nice video man !

Hope you dont drink milk, its the nastiest thing in this world to drink. Adults shouldn't at all. Blood and puss in milk is disgusting.

Thanks for this video. You explained MORE in 5 minutes than my sales guy in 30 minutes. 🤣🤣🤣🤣🤣

Appears to be the same for a C90 Boulevard

A dental pick works good for pin removal

THANK YOU! That was so helpful (and easy!)

This saved so much time that others wasted

Awesome video braddah👏

Do you think I can do the same conversion for a gen1 sv650s without having to change forks. And I want to make the kit as road version, headlight options ?

Hi, will u b at cmp this weekend for ccs 24 season?

Good morning, do you also have the video of the spark plug change? please

Looks like the ktm rc8 at the front now

Thank you for putting this video together. I appreciate it. it's really going to help me.

How can i get back to road use ? 🤣

How i start the lap?

Thanks for the great video! Why not use some anti-seize, like copper paste? Some shops recommend it.

Minivan with low profile open trailer gets 20-22 MPG on highway. That's how I roll... and all stinky fuel stuff is far away from my highway cockpit.

Please do a video on the brake fluid change. Heard the rs660 has a closed system abs so it makes the job a bit harder/different. Thanks a lot in advance.

Does it get hot, no vents for rad cooling

Thanks for your info, i own a 2011 tuono v4, thinking about a rs660 as well, other than the two issues you have, please keep us uupdated if you find anything else! Subbed! Great video helps alot

My brand new Tuono 660 has burnt 2 qts oil in its first 600 miles.

In dynamic mode seems to be a limit in the engine power to 58kW round 78cv. That's little far from 74kW or 100cv declared, you can review the telemetry if you install the original part "MIA" that allow you to connect the smartphone through aprilia's app. Didn't try seriously in race mode yet to see if the digit match, and i'm not than enthusiastic to measure in dyno if the 89cv to the wheel are real. In my opinion Aprilia did a great job with his elctronics assistances that make daily more confortable or why not good riding school

What’s the final word on the experience? How long did you have to wait for a replacement to arrive? I also have a headlight issue. My LED strip burned out on one side. It’s being replaced under warranty but I don’t know how long the parts will take to arrive

Your video was very helpful, thank you ❤

Nicholas, to replace the pads in the rear calipers, would i need to pull the caliper off the bike? and do I tap out the safety pin that contains the spring?

Thank you!

Hi, what oil do you run in your SV?

Crystal clear instructions…..thank you.

Regarding the slide pins, I've seen the grease get crusty and sticky over time so I completely wipe clean both the pin and the cylinder it slides in, including the inside of the boot. Then apply new grease.

Hello, came across your video and really appreciated it. I continuity tested the t-105 thermo disk and had none so im going to try to order that. Is rhere other things i should be aware of

How tall are you?

I’m a bit confused if there’s a pit limiter or not. Manual says yes but not how to turn it on / adjust?

28 ft lb for mounting , union bolt 16.5ft lb

I did this! Thanks for this video, instruction super clear. I wanted to check the brake calipers status of my SV650N 2007 (16 years old bike) and it turned out that two seals were not so sealing and I found mud inside the calipers. I was lucky enough not to need any clamp.

Thank you for the intro/ explanation. Just got me a MY22 Lava Red!

Can you share where you got the obd2 connector and how you put it together.

Is there a way to reset service spanner wrench without having to take it to mechanic to hook up to pc to reset?

Do you mind sharing the files for 3d printing that dash protector? Looks super slick.

How did you reset service wrench on display

Did you have any trouble getting it to slide right on the frame after slicing off the metal bits ? The nubs towards the front are giving me trouble

Italians...

Hi Nicholas, although I would probably never be able to go racing, only have fun on Track Days. It's nice to see you breakdown the cost and how you managed it. Thanks for the video!

How much does the set cost?