Thanks buddy, saved me a headache! Great job!

In my amazon bought model antenna, the dry hole is to the front. Being the case, I'm leaning towards leaving that unsiliconed upon installation. WYT?

Nissan 370 lights are ugly as hell. Nobody can denies that

Are you running oem cats or just straight through test pipes?

I'll spend the extra 5bux in fuel and not need 4Wheel vs needing it

Insane. Wasting energy because the manufacturer won't allow you to tell the body controller that you use low power lighting

All that for a bulb jesus

An open differential distributes power 50/50. This is a full locker so either side can get 100% power not 50/50.

I have the 'steering assist reduced drive with care' message. But the steering has no issues whatsoever. Is this possibly a ground issue and if so, what ground do i look at? The thing had a totally dead battery which was jumped a few times to get the truck moved. But recently put a brand new $300 AGM battery in it. I'm also reading it may need a software update at GM to fix it.

Awesome job on the prepping the alarm . thanks for the video keep them coming

Is the sensor in the same place on a q50 3.0?

For every situation where a G80 would be preferable there will have been 100 situations where a helical diff would be preferable.

Torsen is superior for most driving conditions and more robust. G80 has a slight edge in some extreme situations, but it can also be a negative when it locks up and causes the rear end to slide sideways. Plenty of videos showing trucks with the back end sliding out while little cars drive by without issue.

did you fuse the relay and run power directly from battery? I understand the brake lights will activate the relay but where is the current flowing from? Respectfully nice video

7:59 at this time you said to pick and ignition fuse to tap into but a couple seconds later you said not to tap into ignition. Which one did you mean if you don’t mind? Also what about empty fuse ports? Would we be able to use those spots by just adding a fuse in there? If not how come?

Replacing the oil pump sensor and replacing the pigtail so you won't have trouble with your Cruse control.

You are wrong. Engine covers DO have a purpose. They serve as a homes for rodents.

This man is incredible thanks brother. ❤️

I like how the GM lights flicker like that

Thanks!

Very simple thank you so much

Did you cover the snowplow harness in a video?

Those Philips - ultinon T10 led with crystal lens were very good. Not as bright as zevo. They do have a bit close to warm white like around 5650k. And not 6500 cool white as they claim

I didn’t know we have a courtesy light. Unfortunately our 2016 Toyota Sienna LE did not have that after watching this, and if it was incandescent bulb it would make sense that they would have been burned out long time ago. And that’s a good hiding spot.

There is a release inside the seat head rest tube

We have got Generac Industrial Generator. It shows as over crank and fuel low alarm. What should we do?

Where do u get the software to program it to the vehicle

I can't get that filter box to come out

My 2015 silverado is the most problem riddled truck ever ever owned.

Great opening music . Really got me dancing in the shop. Thank you .

I saw that pin hole on my 2017. I felt like there was something to that. Thanks for including that tip in your new vid!!!

Same here. I have a 2004 GMC YUKON DENALI XL. first started as a slight pause when starting but would start then went to sometimes not starting, to now wont start at all, just click, but also now the power will be normal dash lights come on and click, but just now the battery is suddenly completely dead

My sensor came with an O ring should I take it off to install correctly?

I still use original Liquid Glass. I put 4 coats on the vehicle and its garage kept. Lasts a few years. So easy to use too. Recommend to use in the sun.

Very helpful

Not sure if you will see this but do you know if the z1 symbol is a sticker I could pull off or is it painted on or something similar?

Perfect video thank you!!

Does the car have to be flat / level to do this? I only have ramps I use to do oil changes.. but I heard to do the diff/trans, the car needs to be flat..

Question I have a g 35 2003 I was driving my check engine light came on , I’m not able to accelerate it goes only 2mph some codes popped up I brought a brand new maf sensor and it didn’t work

Question I have a g 35 2003 I was driving my check engine light came on , I’m not able to accelerate it goes only 2mph some codes popped up I brought a brand new maf sensor and it didn’t work

I decided against doing any big power mods so I’m doing stuff like this lol. I’m getting stoptech sport brake pads, replacing brake fluid w/ motul 600, and getting stainless steel brake lines. After that maybe just some handling stuff, *maybe* exhaust, new wheels and tires, and do some paint correction and some kind of ceramic coat. That’ll probably be over a few years so I don’t spend all my money at once lol. Currently my HR has a cold air intake which I think improved the engine sound a lot, and a custom sound system I installed myself with a sealed 10 inch sub with an mdf box in the stock enclosure, double din head unit with wireless CarPlay, and 4 new component speakers with dedicated new speaker lines. This car is already super nice to be in, excited to refine it into something special but still mostly stock in appearance

what brace is that?

I think I have a parasitic draw on my truck with a compustart autostart, have you ever seen this before? Anything I can try?

This guy is the type of mechanic where you get your car back with all kinds of new scratches and he says they must have already been there.

Damn. I hope no one really follow these steps and does this extra and wrong steps lmao smh

Infiniti g35 is 350z’s cousin 😎

Hot panas 🔥🔥🔥🔥🔥🔥🔥🔥🔥knalpot engine exhaust 💨💨💨💨💨💨kamu anthoni surya men pria bagus benar-benar knalpot engine exhaust💨💨💨💨💨💨💨💨 Penis-penis engine exhaust Free 🆓🆓yes baik 👍👍👍👍👍👍

I believe the dye that's in the red handled crimper are for insulated and the dye that you have in the blue handle crimper are designed for heat shrink.

Respect

Doing it now this fucking sucks worst dash I’ve done. Magnet tray with all the bolts and a pile of parts. Instal is ass