It just clicks , not sucking fuel through. Do you have to prime the pump? Like fill it full of fuel first .

THAT WORKED! Like you said, (after spending time to find a 'wire hanger' and bending it) it took less than ten seconds to fish it thru. Thank you!

Autoglass think cars are fitted with a screen before the motor sees any paint 😂 absolute weapons 😂 ive see absolutely loads of screens come out & yes it had paint before a screen 😂 fully cured 2k paint before a screen i say

Brilliant

really crazy !!!! good job !

did you use trigger wire or not ?

Great thanks, but why not put the tap in the bottom ?

your website isn't working

I can only start mine when the engines running. If it's not control panel says E-01, Nobody seems to know why ,.....

If we connect this watt meter to only solar panel and wihout connecting to any other source , then will this meter show the amps.and volts and watt of the solar panel ?

Great game thanks for posting 😊

steering pump

Thanks, got the fan frequency showing and couldn't see how to change it back to temp. Saved me hours of trying options.

how much weight after the build? Did you downplate the vehicle?

Great vid, clear and very useful for the DIY mechanic. Cheers

Are these the same size as a sprinter lwb?

Hi what size ply did you use for the floor

this is brilliant quick question oaths type of sprinter could you still do a suspension lift to have more clearing ?

grea\t vlog thanks for share

Yes this is cool. post some more nice to see you in action 😊

Yes! Thank you. You saved me so much time I really appreciate it.

Thank you !

Not sure, but I think I would have installed it a bit lower on the tank.

Question, have you ever fitted single seat into passenger side, in a Renault Master 2009 van, if so what did you fit ?? if not what would you recommend...

Great work here. I came here to see how easy it is to fit different brand cars. If u can find S class seats for cheap u may want to go for them as they're super comfy for long drives 😊

This is such a shit video m8 sorry just being honest,how come it’s only done 68k and you’ve needed to replace bearings and so many parts it’s got rust aswell 😮don’t give up your day job

Where does the water come from

Well done, a lot of work, looks good

Do your photo's have to colour I've only a black and white printer cheers Chris.

I have build a couple as well. Solar panel on roof i would have used original mounts to roof rack by making brakett to fit panel. Junction box from panel should have been behind panel and not on the side to reduce drag and to avoid problems with debrie life leafs from trees to get tangled. All electric to internal lights and stickers like usb to charge phone should be done before panels are mounted. Lift floor a little and you can have storage under the whole area. Kitchen furniture are way to wide. Could easily been slimmed down to half of the with by choosing another fridge. Doors under bed as sliping doors going on top of each other instead of hinges in the bottom. And to avoid so much cold bridges in insulation I would have used ships insulation in addition to what you used. That is a kind of foam 5mm thick with Silver folio on one side. And remember to make all cables to front seat before montage with stickers. Much easier to do when seat is not there. A roof hatch/ window is also to recommend so you can get some fresh air into the van when sleeping. Finally seal off around floor with sealer so if you spill something on the floor it will not enter in bottom of storage compartments under bed or kitchen area. Good luck to all your builders 😅

what do you think is the best fridge freezer to fit in my us school bus. I like this thetford. Want the largest I can get.

Just bought these seats to fit to my renault master mk2, they look great. Got my single seat bade too so hopefully an easy fit.

Thank you SO much for making this video and sharing it. I am going to buy a Mk1 Connect Sport (I only want the Sport model because it has two sliding doors) and perform a similar conversion myself. Your video has been extremely inspiring ❤

Thanks

Can you tell me how wide you made the bench before it pulls out and what size when it is a full bed thanks

Great tip. Gonna try this technique out on my mini-excavator.

thanks ! your idea is the best ! Saved me hours !

The link you provided to the charger doesnt give the correct results any longer. The chargers returned all run off 240v ac.

Great job. Does it keep rhe desired temperature or change after each use?

You didn't show the ceiling, that's what I was interested in. I don't like the R&R beds either, such an unsocial set up. The prices for a swivel seat are atrocious, just some metal plates and bolts.

Fab content very helpful x

Great vid!! Did you put adhesive between the two panels after cutting the hole out? I'm about to install a window on my Reno Trafic and I am wondering how to treat that double layer of metal after cutting the hole. Cheers!

Did your van start off with a bulkhead & was it much of an issue to remove?

Hey, how does it Looks After Years?

Love this !!!!

What van in your opinion in this size is the most spacious inside? Least bad for rust? Least mechanical issues? We are stuck to needing an auto so obviously have limited choices though.

Where can I find a rubber floor replacement? I’d like to replace my front carpet first the rubber floor cover

What will the minimum ah of the 12v battery need to be to charge the laptop with an inverter?

I never actually got one of those nozzle things? Did that come with your kit?