ThankYOU sir!!! Just purchased my beloved Bernina after trading in an awful newish Singer. I needed therapy after using that thing. I don’t have a buttonhole foot BUT I’m figuring it out.

If you eliminated the music this video would be much better

Great! I have a seized needle bar in a singer 4452. I may try this later. If this doesn't work for me, would you recommend maybe kerosene, alcohol, degreaser or even anti seize to get into those bushings of the needle bar? Thanks for the vid!

What do I do if the lever will not pull Down?

Kill the shit music bro ffs.

Had the same problem with whining and not wanting to shift on my 09 Nissan cube. Changed the cartridge filter and cleaned the screen filter real good and put Castrol transmax cvt fluid and now it works fine !!!

thank you for showing that

Do you know where I could purchase a power cord for my Bernina 731?

Can you add a video of replace the sceen cover and replacing the battery

This is really useful. I have one problem wtih this mahcine, when i do the buttonhole the stitch is really narrow, you have much wider that stitch than i have, any recomandations how to fix it?

Hi and thanke you for a good guide for timing. It is one thing i wonder about. You se i am Swedish and i can not figure out the meaning of the shortening/the abbreviations. (I always apologize for my SwEnglish) You never know when you tripping over a spell. 🤪😂😊🙂👍

Any chance you could slow this down? YT doesn’t offer playback speed option on shorts!

Does anyone know if this issue also locks the push button top? My Denali locks unlocks fine after I disconnect the battery and it's all clean, but as soon as I close the door everything won't work. I'm thinking security... bc as soon as I reset everything it will work fine then it doesn't. I didn't even have to take off the panel to get it open, there's not rust and I lubed everything, I tried actuator while it was open and nothing after the first time I use it... next thing I will do is read the output to the electronics to see if it's even getting spark to open

U need to replace the LED or install a resistor cuz now all the other LEDs in that section are going to absorb that current

More carbs at high RPM= more better.

Omg thank you your video is only one that really help me.

very helpful, thanks.

Thank you, just what i needed

Thank you share have a 2011 nissan cube still here noise never do transmission filter but will

To the point. Thank you. A+

Thanks!!

Thank you so much. You are amazing! I have now done button holes for the first time in 20 years after getting the machine from my mother. Husband unstuck the slider with CRC and heat from a hair dryer. Works like magic now!

Thank you for sharing this! This just helped me solve a similar problem in a 2008 Trailblazer

Thank you! I love my old Bernina but there is so much about her I don't know.

Do you have any recommendations how to open the upper lid of the Bernina 730 (to oil the inside)?

this taught me so much about my machine thank you!!!

Speak up, Silent Bob

love that these videos all start after its opened and unlocked lol

I could not figure out why my machine wouldn't sew a buttonhole correctly. Turns out my slider is stuck. This video and the comments are so helpful - now I have to get to work on "unsticking" the slider!

Thank you! I just inherited this machine and had no idea how to do button holes. Thanks for a short and direct tutorial!

Mmmm. This is one thing that I do not like about these boards is when some thing like this happens. This is why I prefer diy Cob Builds. Maybe it's because I am old and I to Hifi separates Tape deck, eq, tuner, amp, turntable and of course CD player... 👍

When i press lock button on my fob i don’t hear the lock working in the cargo door and I can’t get the door to open by using a screwdriver to move the levers in the access hole. Any suggestions?

Have a 2010 cube. I ran into the same whine / noise and ran across your video. Replaced the screen, filter, and whatever fluid was in the pan. Whine is now gone completely. Very thankful that you uploaded this video. I’m draining the pan and adding more new fluid this weekend to hopefully prolong the life of ole cubert.

Will that make my FOB remote stop working. They both stop at the same time

Did the pitch of the whine change with the revs?

I just got duped and bought a cube with the same noise. It only does it when it's a cold start tho. Fingers crossed doing this will fix it. Thanks for the vid and glimmer of hope

When u change the secondary filter. Did u change also the whole housing or just the filter?

What can Ii do to make my slider button pull downward if it is stuck? So glad to find your video. I have my mom's Bernina 730 and hard to find specific videos for it, thank you!!

After 220k miles and immaculate care for my 09 cube, got a cvt whine. I don't currently have the money or time to fix it unfortunately. In the middle of a move and an extensive work project. Some asshole over filled it with the wrong fluid.

Thank you for this posting. It is is the only one that displayed this part of the Envoy rear latch with a way to fix it. It worked great!!! Saved saved me at least $100. Contact cleaner, WD40, air nozzle, contact cleaner, air nozzle, more WD40 and working the lever back and forth finally clicked easily and and started working. Great video! Mine.was a 2003 Envoy slt.

Yours is the only video that talks about how to do buttons on the Bernina 730 Record.

Swapped mine a year ago....... I'm just now getting the guts to put the CV axles back in, transfer case, intake and exhaust manifold. I'm watching your video and I'm just as excited as you are

I want to go find the designers of this vehicle, go to their house, then kick them right between the legs so they can't breed any more!

Nice

Breathing too loud for me

Took my Bernina 801 into the shop to get the feed dogs fixed. They said it couldn’t be fixed. So disappointed. Watched your video and tried to fix mine; however, there is a metal pin that has come out, and I don’t know where to put it back. I can see that same pin (looks like the bottom of a safety pin 🧷) in your video, but can’t tell where it should go. Any suggestions? So sad if I can’t use this Bernina anymore! It will be like a death in the family! 🥺😉

Thank you ! I can turn the feed dogs knob without any problem, but the feed dogs keep lifting. On my machine, it seems to work exactly like on yours so I can't see what I'm doing wrong.

Good video, genuine Bernina cam gears for this are no longer made, the replacement ones work perfectly, do not be scared by the fact the gear may not be as tight as the original when in position the cams rotate and each stitch the machine takes turns the cam stack quite a bit and the little play in the movement makes no difference and i have three of these machines i use and have replaced the same gears in each, on I just did again for the second time. I like to use Liquid Bearings synthetic oil on all my machines it works so much better and longer than any conventional oil I have ever used, this is available on Amazon or E-Bay and works on clocks as well. I have been using this for about 10 years and I will not use anything else for light oil.

My 2008 won't lock. It sounds like the same problem. How did you get the panels off to expose the locking mechanism. I suspect my actuator is dirty as well.

Thank you so much for your video, I have been searching for how to take apart a bernina 730 .I would so appreciate a video on the rest of what you described! I have 2 issues one was the feed dog knob being seized the other is my machine doesn't want to reverse. The knob moves fine is just stitching on the spot until I release it?