Great video. I have a question. I just bought brand new 2.73 axles for the front and rear. I took them out to Predator to have the ARB locker kits installed. I installed the rear first. Here's my video. kzbin.info/www/bejne/pJqVp5Khid6Keck. Once I got it installed and after my video, I noticed that my gear oil is being pumped out of the vent line and into the vent system. I was wondering if you had the same problem? I read a lot of blogs that said this was common with ARB's. And this is while they are NOT engaged. I also notice that the gear oil is making its way to my right rear gear hub. The level gets higher on the sight glass after driving. Most of the blogs said to increase the size of the vent system.

Where did u get motor mounts? What trans? Need - more - info!!!!

Hey enjoyed all your videos. Do you have any updates videos??

Put seal in freezer before install

Great tour thanks 🙏 for sharing. Did you ever got your Humvee insured?

Great video. Helped me a ton

Do you recommend to buy OEM breaks and rotors? Or just from a local part store

Feed that impact gun. 1/2” hose with high flow fittings. You’ll be surprised

Hey i’ve seen all your videos …very nice… so it’s been five years do you still have your Hmmwv??

Thanks for this video, I helped me to lift mine! Curious though, why didn't you use spring compressors? I did and it was pretty straightforward (two videos). I also took the sway bar loose, which I may have missed on this video. Thanks again!

your is gas engine swap right?

65/73 ftlbs could be different as some versions have different sizes nuts on top and bottom. I know mine has 5/16 top and 7/16 bottom - some use both 7/16 and some use 3/8 too.... This is just a guess. But if both top and bottom are the same size, most likely, they will use the same torque specs

Thanks a million

What did you do about the horn? Nevermind. I saw the next video.

Daaaaaaaaaaaaaamn, lucky. You should swing by our shop when you pass through St Augustine Florida again.

Pretty cool, congrats.

Do you think cutting the airbox like you did, would be beneficial for a non turbo stock 6.5 Diesel in mine?

Did you install the ARB? any video?

I have 2 units id like to convert

Great video not sure what I would have done without it. I am getting some air leaking is that OK?

How did you get the wire out when it was embedded in the steering column?

Any updates on the Humvee? It looks like your highway cruising RPM is around 3,000-3,400 rpm? That seems like it's not going into overdrive.

That's not a lift.

I’ve seen all your videos very nice!! When will you make a new video see what have you done to the Hmmwv lately?

Did the original hmmwv transmission mate to the lsx? I haven't seen all your videos yet but I'm planning on a lsx swap also.

Hey what’s the name brand your electric fans please?? Thanks

Could a whiffle charger be put on?

He’s my dad

Hey Charlotte NC here… what’s the size and the brand name of your fans please??. Thanks

It looks nice btw I’m Jason’s son and macys brother

Absolutely cool Hmmwv !!! What is the brand name for electric fans? Thanks

They are up a few bucks. $500 now

Black rims with 0” offset will give it just what it needs

Are the boots the same size for both types of ball joints?

When you don't have the weight available to compress the spring use a chain hoist. You have to get creative to rig it properly, but I just used a 2 ton chain hoist to compress the springs on my HMMWV when the body, drive train, and majority of the chassis was taken apart and it worked beautifully. I went around the bottom of the control arm right at the ball joint with the dead hook, and the body hook went above the shock pivot and to the opposite frame rail. I used a manual chain hoist this time, but the last time I had to do something similar I used an electric 2 ton hoist and it was all to easy. Just be careful not matter what you are doing, stored energy in a spring can mame or kill you. Use a small chain through the frame and a few coils, if something let's go unexpectedly the chain will restrain the spring. Be careful out there.

Nice work!

Someone said you were running 12's in the 1/4th mile with this thing... wheres that video???

which starter are you using? doesn't look like an OEM AMG starter

Hey I know your videos might be old but I just purchased my first Humvee. And I like watching your videos very informing. Question, how do you take out the hatch? I think it’s glued in. What do you think? Have you ever heard of that?

Hey, I know this is a video but great work!! I have a question would you have a power steering gearbox you would sell me?? Thanks

Man very nice!! I know this may be a old video but cool!! I just bought my first Hmmwv …. question if I put.40s on is 2” lift kit enough or do I have to do the body too??? Thanks

Any one else have the problem that when the lower arm is down the spring is still tight?

I needed this video! Thank you so much!!

How was the gas mileage with the lsx swap?

Very interesting mod.

Great video to show a lot of the important steps. I'll be replacing shocks soon on our H1 and this video was a great view of the critical components involved.

Hey bud! What’s that bed flashing called?

Excited to see you back; and appreciate you making these videos

You: I could do this... cuz I'm lazy... Or it can be done properly... refer to actual service manual

Your daughter stole the show. What a personality. Hahaha