タイトルは日本語、中身英語、わけわからん

Hello - How to reset GRBL configurations (My setup for my Sculpfun S9 is wrong)

hi , thx for the codes. can I use this program for using rotary encoders for flight sim ?

thankyou sir i learn a lot

How the F*** you made 32 buttons with a 14 button pin board????

this is great thanks

Your demo on the little girl photo says your job only took 26 minutes. Mine shows 10 hours. What am I doing wrong? I followed all your steps.

Thank you so much learing on my own and wish i would have found this sooner so thank you

Thanks for the tips, worked very well for me

Wait, so this lasergrbl or whatever can’t draw pics?! You have to have a separate program just for the images?!! Wtf?!!

i had the same issue with jerkiness while burning as it jumped over the white unburned area, i slowed the jog speed way down and kept it close to the burn speed, i noticed the laser didnt jump as much and ran much smoother, it takes a little longer to burn but the results were much cleaner. plus make sure your belt tension is set right with no slop, the belts do stretch a hair after a while and they tell you to trim off the excess when setting up the machine - dont, it gives you something to grip on to re-tension the belt then tuck the free end under the channel so its out of the way, you cant put the end cap on but thats just for looks so leave the cap off on the free end.

I am not american and you speak too much

Is there anyway to reset the axis ? Mine going left for no reason

Great, thank you sir.

How?

I am using a 360 degree hall effects sensor and trying to get zero to full throttle in only 180 degree turn of a handle. How can I calibrate this? It is for a home built helicopter collective and the hand throttle can only rotate 180 degrees. thanks

any wiring diagram ? ...please

Can you use GRBL with Creality printers?

How would you wire the 32 buttons and four axis?

Thank you for great information

Thanks for the video, can you make you own dimensions, or is is locked

Hi! I am using this lib for my Yoke system, works weel, I only have 2 issue so far, maybe someone could help: 1) how to recognize it as a driving wheel, so instead of X/ Y axis rotation the wndows setting page should show wheel rotation? 2) maybe it is not the libs failure and it is for any game controllers in wondos, but it does not show the correct throttle value until I change it. So I have to push throttle each time startig the game or connecting device, canot leave it as set for a good neutral throttle for example for airplane start.... How to overcome those small issues? Thanks for the lib and tutorial!

very nice project but how to disable unojoy

Hi nice video, What laser machine did you use?. Thanks,

Thanks bro

Can you send me the software download link

I haven't tried it yet but i have converted my photo to a pencil drawing to see what sort of picture I get

Thank you so much, your instruction is very clearly! Finally, i find the solution for my project <3

Great video that helps new users (like me) learn how to use GRBL software. It's saved me hours of searching to find answers. Your responses to user questions and comments are also very informative.

How do you conect the joystick. I am lost.

Please I need 3 NC or G CODE format files in size 10 cm * 15 cm Thank you

Very helpful video. Thanks. Looks like it has been a couple of years since you last posted a video. Are you still active.? Hard to find good tutorial type videos.

Thank you very much for your excellent video Kevin. Helped me a lot with inkscape as well.

there are several problems with LaserGRBL. number 1 : it's A pain in the ass to pause the burning. one of the biggest laser killers is HEAT. it is recommended that you allow your laser to cool off for 5 minutes after each 10 - 15 minutes of burning. even with a HEATSINK your laser will get HOT. the heatsink may feel cool but the laser inside gets super hot. a fan on the laser does help but do you want to buy a new laser all the time? to pause the burning.. click the stop sign icon at the bottom right. to resume click the running figure next to it. remember to allow your laser to cool every once in a while. I usually burn for 5 to 8 minutes and cool down for about 5 minutes. number 2 problem : the GRBL firmware. I see in this video you used grbl0.9 the newest is grbl1.1h. both very similar. but each time i open LaserGRBL and load my machine i must set the firmware to laser mode($32=1). i have downloaded the source code and edited the GRBL firmware and recompiled it so that is no longer the case for me, but others may still have that issue. number 3: the GRBL firmware assumes that all machines are the same...they are NOT. for instance my machine uses 90 steps per mm. i have a mini laser that uses 82 steps per mm. GRBL firmware by default uses 250 steps per mm( I think,,it may be 200 per). to change the steps you must type in $100=XX, and $101=XX (XX=number of steps needed). I forget the formula, but there is a video on youtube that shows you how to calculate the steps per mm. I started with a image of a box with heavy outlines. I made it render at 10mm X 10mm. after it lasered i measured the image, then adjusted the steps to match what was needed per mm. like I said my A-3 machine was 90 steps per mm and my mini laser(made from dvd drives) was 82 steps per mm.( not perfect but it WORKS)

Kevin Brigadier. Cheers. But I have a question, once you get the print set up correctly. Can you save it, make a copy of the file then remove the original image and add a new image, keeping all the settings, to save time. As you can probably guess I'm very new to this.

Hey, if I use mosfet with 250mw laser and control the gate with PWM, is it good way to burn pictures?

why my buttons don't work

I don't know why those niggas. Cannot really be legit on tutorials They're just showing off

The nigga is not helpfully lol Thumbs down

Thank you for the tutorial! One thing I am really missing with this software is the option to run focal adjustment for the laser (lower light option) and "show path" option which would show me the maximal burn area for the current project. Are these buried somewhere in the software or are they just missing? Thanks!

I take it resolution that the picture you are trying to convert and burn has a lot to do with the quality of the burn?

Thanks i used m3 m5 using toggle button... It worked fine for few min...now it doesnt work but does show m3 m 5 commands on screen as i toggle

Thanks..i tried doing custom button for toggle laser on off...it worked for a few reps but then stopped working....the m3 m5 shows up on screen when toggling but laser doesnt turn on

Worthless video! Told nothing 💩

And how do u know where your laser point is?...there is no way to turn laser on low to see where your lcation is..via lasergrbl...younhave to guess which is unacceptable method

Does anyone know how to reset xy 00 start point in lasergrbl? Only way i have found is to unplug and plug back in which is an unacceptable method

Hi, you have the code and schematics ?

Hi! Which power laser used? Thanks!

My engraver won’t connect to the software, please help! I’ve tried all the listed coms

try using a software called "fengrave" ...first convert image to .DFX than load into "fengrave" to convert to gcode ...I used it on a cnc machine and it works great.