Thank you! Mine is smelling! Didn’t know how to clean it.

Can't hear u

On my Chevy app, it has it 84200271 for a 2015 Tahoe.

Whoa! Fred Armisen has a youtube channel!

The new Leonardo Da vinci

This is one of the first things you learn as a carpenter apprentice in little Swissy land. Been using this method since 1976 to setup all my saws. Radial Arm Saw, Mitre-slider and Table saw. I used to hate the f-cking radial arm saws, because as an apprentice it was your job to make sure that they're all square. Got about 15 to 20 cuts out of it and those f-ckers were out by about 1/16th. over 12" wide board. Also hated them because they where f-cking heavy back then, at least 150 lbs. Guess who had to haul them around ? You guessed rite !!

That muffler is probably the funniest biggest waste of time. I mean the shirt says it all . . . . 10 decibals + make this video + my time = this guy can't fix _ _ _ _ . Fill in the blank

I made one of these today. It works great.

Very well detailed. Thanks for the inspiration.

Probably will never remove an adhesive mirror from the wall, but I found this video very, very interesting and informative. Thanks for sharing.

Bag it and use hepa filters

Is that yellow stuff spray foam? Do you recommend that too? Thank you

So.e video i watched maybe yours??? Offered up the idea to PUT A POOL FILYER COVER ON your wet dry vac filter b4 use it will block the filter from bei g damaged

Hi mark from england I use the 400 wet Stone and 1000 grip wet Stone and then use another strap.I find they are sharp

You and your friend do good work lol

What the cost benefit of the dust catcher? How many new filters could have you purchased for the cost of the setup you created?

Sound management was very poor. Too low on the voice and too loud on surrounding inputs.

7:09 LOL It's funny how neither one of them fit and you have to go back to basics. If two drain tools don't fit, and even your go-to groove joint pliers doesn't fit....then they need to just pass a law that these damn drain kits have to come with the tool to screw them in at this point 🤣 This is ridiculous.

Great video.

Jokes on you, I tied you I tied not and have a security system and surveillance cameras also motion detectors

@4:29 Putting the muffler on the exhaust port will throttle the suction of the vacuum.

Want it quiet? Replace the motor bushing with a bearing. I did, huge difference. Going on 10 years now.

Use a bag

I use the shop vac to vacuum the filter

I want to see the starting of diagonal settings

Thanks learned a lot about this soft water system and cleaning and maintance

I started the first shim and the whole thing let loose! That was EASY! Thanks!

Thank you for giving the example sound at the beginning. My girlfriend and I were going nuts trying to translate the sound to a google search.

My lights are realy low and the tail lights not work any body not Wy

You should definitely sell this rebuild in different sizes, I am sure they will sell.

Cool ideas but I am curious if the muffler creates any drag on the intake of the shop vac. In other words, how much suction do you lose using the muffler? It's a great idea and I will do it with mine but I'm just curious. I don't have an areoameter so I was wondering if you could answer the question.

Awesome . Didnu shut off the resin tank hose before cleaning? I saw you at tye end of the video reaching behind the system and twisted something. Thx

Very helpful. Ended up running a small zip tie through the holes in reverse, then taped the string to it and rand it back no problem.

The video thumbnail image showed a 'spade bit'. No spade bit was used in video. Won't watch nor trust this channel again, enjoy thumbs down.

Very cool. You could the top bucket

What a great hack, thanks for a great solution:)

i thought you said we don't need any straight edge and yet you used one? Huh?

Thank you. We dont know when was our rebuilt but will take on this project next if the iron out cleaning doesnt help.

Someone, anyone, please design a latching top to the canister of these shop vacs. These flimsy plastic clip handles loosen and wear out….my pet peeves…..

Design a vac that has a flat top so that you can put tools and screws there when working on a project…it is always near your project anyway…might as well use this roll-round appliance for two uses.

Design a vacuum that can be stored in the kneehole of a desk…

Hose storage and attachment storage on the unit are under-designed…..

Give me a shop vac with soft wheels that can roll over its own cord without tipping over….or scratching the finish on a nice floor.

Good tutorial, nice jig. A simple note, at 8:15 NEVER keep your fingers anywhere near the blade. If that saw hits a knot or jumps up you could lose the fingers or a hand. I've personally had to pickup a coworker's fingers from simple mistakes like this and it wasn't fun for either of us.

Very helpful. Thanks.

Instead of string better use a solid straigt piece of wood or metal

This isn't even in the same universe as Festool so comparing the two is silly. But this is a legit idea. Thanks for sharing.

Next level stupid.

I just watched about 8 of these videos and yours is miles above the others. Great detail and insight about what the seal does when you close the door and about getting tight fits. 10/10

I am a professional cabinet maker. I just don’t understand this whole track saw fad? A good tablesaw or panel saw, I have never seen a cabinet shop use a track saw. If you are at a job site and you know you need panels a certain size, just be prepared and cut them at your shop and bring them with you. I think they are kinds of a gimmick