thanks for great video!do u think feasible to move basin higher up to suit user's height (new flat)?
@diyyangSG3 күн бұрын
@@jean700 hi yes, you can do that. Just take note of your drain pipe and inlet pipe when you shift up need to increase the length of both of them.
@jean7002 күн бұрын
@@diyyangSG tks for prompt reply.appreciate it!👍
@aileennidea11644 күн бұрын
Hi what if the toggle near spring was broke, should I buy the safety switch than sticking it back?
@diyyangSG4 күн бұрын
@@aileennidea1164 Hihi, personally I have not stick it back before so not sure it will last, usually I buy new one. But sometime is hard to find a replacement so you have stick back instead.
@aileennidea11644 күн бұрын
@@diyyangSGI just sticked it back but the error keeps showing 😢
@diyyangSG3 күн бұрын
@@aileennidea1164 oh no, thank you for sharing what you have experienced. ❤️
@rushdanabdulghani21234 күн бұрын
Tkasih..sgt membantu👍
@diyyangSG4 күн бұрын
Welcome😊. Thank you for leaving a comment❤️
@momogunsabah6 күн бұрын
My machine problem, small water input panasonic aquabeat na f70s7
@diyyangSG6 күн бұрын
@@momogunsabah if small water input, this video I have might be able to help you. kzbin.info/www/bejne/jqm3n52vis6pesksi=tpeN7fzN4-MHEC_6
@Jaymore63913 күн бұрын
Thank you managed to repair the washing machine, gor under $20
@diyyangSG13 күн бұрын
Welcome😊 $20👍👍 Nice diy, save money 💰😜
@tequilatyrant399214 күн бұрын
your video is great. well made. I am also wondering if mine is a belt problem or not. My wash function doesnt work, but the spin function works. so the drum does spin at a high rpm for the spin. so cant be the belt i suppose.
@diyyangSG14 күн бұрын
@@tequilatyrant3992 thank you for the praise. Appreciate it alot🙏🙏 yes yours doesn't sound like it is the belt. If it fills water and cannot start spinning. Maybe is the pressure level sensor. But I not professional ah😂 I also try and error type
@melissaed405921 күн бұрын
I used this method and cleared out all the rust, but it isn't working. Thank You tho for this informative guide. Will look at next steps
@diyyangSG20 күн бұрын
Thank you so much for watching the video and give it a try🙏. But sad that it didn't help you 😭. Hope you can find another video to solve it
@silverhawk91122 күн бұрын
I almost threw away my Samsung washing machine , thanks to this video that I learnt a simple fix with a $5 compatible Samsung water inlet valve from Taobao is able to solve the issue. Now my 3 year old Samsung Washing Machine is working again. Hope it lasts for another 5 years at least.
@diyyangSG22 күн бұрын
@@silverhawk911 Nice job, yes yes. My valve have been changed since 3 years ago and it is still working. I believe yours also can last for many more year 🥰.
@maoteh25 күн бұрын
Works wonders. My washing machine is working again.. took only 10 mins to fix.. thank you so so much!
@diyyangSG25 күн бұрын
@@maoteh welcome 😊 nice job. Thank you for leaving us a comment and letting us know ur success💗
@raizelloveАй бұрын
If I can give u a kiss I would!!!! So tight on money and thought I would have to purchase a new washing machine 😅😅😅😅 part arrived today and the washing machine is working smoothly now 🎉🎉🎉🎉🎉 THANK YOU 🙏
@diyyangSGАй бұрын
@@raizelloveVery happy my video save your day 🥰👍. Let's hope for washing machine to last many more years❤️
@layno88Ай бұрын
Just did mine thank you so much!!!
@diyyangSGАй бұрын
@@layno88 Welcome 😊 thank you for leaving a comment.
@simonking670Ай бұрын
Love you sweet baby lips...and I'm not even gay
@junaidahmohamedsaman7612Ай бұрын
Thank you so much and may God bless u.Saved us $$$ of buying a new ones.Mine is about 8 yrs..the part where need to take out the white and black part was challenging as it was tight Nevertherless managed to do it.spent abt 3 hrs but worth every cents if not have to pay $160 for repair
@diyyangSGАй бұрын
@@junaidahmohamedsaman7612 Welcome. Thank you for sharing your success story👍😊 Wow 8 years. Last time product does last so much longer. Hope it can last many more years😊
@MarJorieMamaril-s1iАй бұрын
I already replace my water inlet but the problem not is it won’t stop filling water
@diyyangSGАй бұрын
@@MarJorieMamaril-s1i Hi, when you press stop button does the water stop? If it stops then might be your water pressure sensor that is faulty. Not very sure but that's what I will suspect if it happens to me.
@elizahellcatАй бұрын
Thank you for the video! It fixed my issue. Appreciate you!
@diyyangSGАй бұрын
Nice 👍, thank you so much for leaving a comment. ❤️
@hafriz87462 ай бұрын
Not sure if u around still, my issue is the door cant shut well. Always a minor gap on top. Can u advise
@diyyangSG2 ай бұрын
Hihi, the door roller have 2 type one if a washer in between and one without( what I used in the video) Maybe you can click this link and you see the door roller there is a slight difference- s.lazada.sg/s.1f4rh Hope this is the gap you are talking about
@hafriz87462 ай бұрын
@@diyyangSG think i find out the issue, is the riveted stopper at top. Its like below the rail now. No idea how to solve this
@diyyangSG2 ай бұрын
I have not met this issue before, not able give advice to help 🙏sorry
@njlllljn2 ай бұрын
hi my washing machine water inlet is working for the hand wash one but the powder dispenser one isn't working..., what might be the issue?? so I still need to change the inlet? this always happens after i descale the machine....
@diyyangSG2 ай бұрын
You can take a look at this KZbinr video for descaling valve issue. I think he does a very detailed video. That might be able to help you. kzbin.info/www/bejne/m6S9amh5r7ylnKMsi=Io064tGQPjpfVqmE
@ruqaiyaabbasi12292 ай бұрын
I cleaned my filter by opening it same way Water flow became great but after sometime the machine stop taking water. Sometimes it will take and then stop. Does it need valve change? I can't hear the machine sound it used to make while taking water
@diyyangSG2 ай бұрын
Hi, if the solenoid does not make any sound when take in water then changing the valve most probably will work. But there got a slight possibility that is the main board have issue not sending signal
@JessalynPicorro2 ай бұрын
Thank you for saving my day! It works 👍👍👍👍
@diyyangSG2 ай бұрын
Glad it helped! 😊👍. Thank you for leaving a comment
@counterguardian61452 ай бұрын
I know this, I was just hoping there was some way to change it like a regular lightbulb...somehow... why didn't they design them like that?
@diyyangSG2 ай бұрын
Agree with you. Hope someone will create something better in future. Safer for everyone to change out themselves
@bobschiller74162 ай бұрын
Not my model number but this was the only video on YT I could find about access via the rear panel on a front control machine. I like the Picture in Picture details, very helpful. Thank you
@motshehiramakatsa17242 ай бұрын
Hi bro, with my washer the drain pump continuously runs non stop, can you help me 😢
@diyyangSG2 ай бұрын
@@motshehiramakatsa1724 Hi, Have no experience that on this machine yet but when you press stop does the drain pump stop? If not, likely the drain pump is spoilt.
@hidayahrahman13652 ай бұрын
When you faced this problem, can your machine still do spin cycle? Mine just stuck when no water come out. Cant even do spin cycle.
@diyyangSG2 ай бұрын
Hi, mine just hang there, mine didn't move on to spin cycle so I just tried to change valve after I check my water supply hose is not blocked
@hidayahrahman13652 ай бұрын
@@diyyangSGhi, i just changed the valve, still doesn’t work😭
@diyyangSG2 ай бұрын
@@hidayahrahman1365 ohno sorry to hear that, this sounds like it might be board issue
@seansunable12 ай бұрын
Excellent Video - Thank You 👍 ... Question does it not create out of balance - laying the Panasonic Washing Machine on its side?
@diyyangSG2 ай бұрын
In the event your rod drop out. You just have to hook the rob back in place. It will be back in balance again. Mine didn't drop out so I didn't have video clip on hooking back 🙏
@oo-nf5bs2 ай бұрын
Just had this problem yesterday and found your guide today. You’re THE MAN bro! Thank you so much
@diyyangSG2 ай бұрын
Nice, thank you bro for leaving a comment to let me know ur success👍👍😊
@oo-nf5bs2 ай бұрын
@@diyyangSG you’re welcome bro. Cracked solenoid casing. Replaced the whole module and the washing machine water issue is now solved. Cheers bro.
@umangshah39153 ай бұрын
Thanks buddy. .. I need one more help. How to change door hinge of this machine. . plz help me
@diyyangSG3 ай бұрын
Hi sorry, I have not tried it before. Not able to help on that 🙏
@nyashatimuri63183 ай бұрын
Can i manually put water
@diyyangSG3 ай бұрын
I haven't try before but I think it is possible if the error code for no water only appears after awhile
@yennycoquin6533 ай бұрын
So basically need to buy a new set to change, am i right?
@diyyangSG3 ай бұрын
@@yennycoquin653 hi yes, need to buy a new solenoid valve to change. Do take note is not 100% success rate. Some did share can be circuit board issues too.
@chaindoll3 ай бұрын
Thanks man. You have saved my money from buy a new washing machine.
@diyyangSG3 ай бұрын
Nice! Thank you for letting me know Ur success 👍😊
@shimaema81393 ай бұрын
Thank you.. As women I can DIY my self.. 😂
@diyyangSG3 ай бұрын
Welcome 😊.Nice job👍👍 thanks for leaving a comment to motivate people to try
@huiseetan72383 ай бұрын
Mr Yang, thank you so much! I watched yr video and went straight to buy the plunger rod …. It worked! Thank you once again.
@diyyangSG3 ай бұрын
Welcome😊👍. Nice job. Glad to share and help. Thanks for leaving a comment 🥰
@TrafalgarLawHeart3 ай бұрын
Thanks.. its works for me. Easy to change the new part. Not so hard to push in.
@diyyangSG3 ай бұрын
Welcome👍 Great job. Thanks for leaving a comment to motivate people to try out too😊
@yantaoxiao3 ай бұрын
Professional! Your previous videos really helped me alot! Appreciate your kindness to share! I have shared your videos with my loved ones! Thk you!
@diyyangSG3 ай бұрын
Thank you so much for the kind words ❤️🥰. Hope the video will help someone in this world
@farhangm77804 ай бұрын
great
@mohammedakram26614 ай бұрын
Thanks buddy it's work u save my money 🤑 💖
@diyyangSG4 ай бұрын
Nice. Great job 👍
@yantaoxiao5 ай бұрын
Hi, I have just bought the Anti Slippery Solution. I have applied on my toilet's floor. Great! It really helps alot!! Thk you for your great videos!!
@njburj83935 ай бұрын
Not sure if it would be the same fix. Before, when there's no water coming in from the inlet valve I can hear sound when it should taking in water. Replacement solves it. I got the same issue again but now, I don't hear a sound. What do I need to check first? I already tried removing-putting back in but same issue.
@diyyangSG5 ай бұрын
Hi, first maybe you can check whether your water supply have any issues. Second, i will use a multimeter to check whether there are 240V sending to the solenoid valve. Because i hear before that there are chances the board could be the issue instead of the valve
@christanchua99395 ай бұрын
I don't usually comment but thanks very much for making this video, saved me lots of time and money.
@diyyangSG5 ай бұрын
That's very nice of you🥰. Thank you for leaving a comment to let me know ur success and appreciate it alot👍
@JoGiles775 ай бұрын
Beautiful! Exactly what I needed to know. Much thanks. Wish me luck 😂
@diyyangSG5 ай бұрын
Thank you for leaving a comment. All the best, you can do it👍😊 if it works you can save alot of money 💰
@vincy25005 ай бұрын
Thanks a lot mate. I managed to save couple of hundred dollars because of your video.
@diyyangSG5 ай бұрын
Welcome 😊. Nice job👍, Thank you dropping a comment too
@vinodhsss5 ай бұрын
This video helped a lot....thanks for this...saved lot of money
@loveleads49345 ай бұрын
@DIYYANG Please am still experiencing the same U12 error code even after changing the washing machine door safety switch with a new one it still does the same U12 error when it enters into rinsing mode.. please i need a technician. Thank you
@diyyangSG5 ай бұрын
Sorry 😔 didn't happen to me. Not very sure. 🙏 Hope someone experience it can share any solution
@ronojitpal24275 ай бұрын
Mera vai kam laga haa
@mbeadles26 ай бұрын
THANK YOU!!
@diyyangSG6 ай бұрын
Welcome😊. Glad my video help you
@yantaoxiao6 ай бұрын
Your videos helped alot of people!! Your kind deeds will always be remembered!!! Thank you so much!!!!
@diyyangSG6 ай бұрын
Thank you so much for the kind words🙏. This comment gives me the motivation to continue sharing 🥰
@alexanderthegreat_CarGuy6 ай бұрын
I bought a brand new piece and still the same issues. Any help?? The code is reading water valve still! 😫😫
@diyyangSG6 ай бұрын
Hi sorry to hear that. it is not a good news, there is a possibility your main board is spoilt or the wire is damaged somewhere. If you have multimeter you can test if the wire connecting to the valve has voltage during each steps and test the resistance of the new water valve. Otherwise, it is still better to replace the new washer instead. As the cost of the board is quite high.