You can use the fel pro gaskets for the vvt solenoid. The smaller one is correct you just have to put RTV around the gasket and then put grease or oil around the inside so it slides around the solenoid easily
@mikedavis773319 күн бұрын
I have a 2014 Sonata I use 1157 they still to hot if change to LED do I need to add a circuit board are just replace the bulb Thanks!
@DavidJWarEagle19 күн бұрын
Just replace the bulb as far as I know. You’re welcome!
@Alan_Edwards26 күн бұрын
It can be done without taking out the alternator or removing the bolts....I know because I just finished replacing mine. But it will take a lot of patience and time...and a little luck. The hardest part of the job is getting the connector off of the sensor because it has a clip that must be slid to the side before you can depress the tab and pull it off. I admit it took me over an hour using a small screw driver and some mirrors to undo the clip, but getting at the alternator bolts is a PITA too so I guess six of one and I choose working on getting the clip moved. Once you do that and baring you have the right size socket with the correct depth barrel, it's easy peasy after that.
@DavidJWarEagle19 күн бұрын
Good call on that. Hopefully I won’t have to do that job again any time soon but will likely give this method a try. Thanks.
@jeremydallenАй бұрын
Told my buddy about this, nice quick to the point video!
@DavidJWarEagleАй бұрын
That’s great! Hope your buddy can use the info. Thanks for the comment.
@ricardocalderon89462 ай бұрын
My ram 1500 don’t start just cranking I have this code I check maybe that’s what is causing the no start?
@influxvision2 ай бұрын
Can that sensor be cleaned with MAF sensor cleaner spray?
@tone22592 ай бұрын
If this sensor were to leak would it drip down to the corner of the oil pan
@DavidJWarEagle2 ай бұрын
I think that is possible. Normally I use my cell phone to make a short video to view locations that are hard to see, like around that sensor.
@jayrey17132 ай бұрын
How to know when to replace brake sensor. Pads and rotors have been changed. Bas light keeps coming back on and when yhat happens the rear passenger brake either is non existent or it does work.
@DavidJWarEagle2 ай бұрын
Hi, I would try to pull the diagnostic codes to make that determination.
@davidreed33572 ай бұрын
So it's a stop to keep it from vibrating past the post. Cool
@DavidJWarEagle2 ай бұрын
Yep, that’s right. It’s a pretty simple solution!
@VSLComputers2 ай бұрын
Perfect! Thank you so much!
@DavidJWarEagle2 ай бұрын
You’re welcome. Thanks for watching!
@cesarsevillaacosta73383 ай бұрын
Great job sr...many blessings
@DavidJWarEagle2 ай бұрын
You’re welcome. Thanks for the comment!
@elizabethalarid86733 ай бұрын
thanks man - really helped and I like your style. "no smoke and I didn't get knocked off the ladder". celebrate the positives right!
@DavidJWarEagle3 ай бұрын
You’re welcome! It’s always a good day when you don’t fall off a ladder. Thanks for watching.
@86-Trueno3 ай бұрын
Thank you for this video. Last weekend I did the front valve cover to change the vvt solenoid but struggled to get the power steering reservoir off so I have to go back and do the rear valve cover and now I feel like I can get it done
@DavidJWarEagle3 ай бұрын
You’re welcome and glad the videos helped you. Thank you for watching!
@chopchop1234567891003 ай бұрын
🎉
@gabrielmoran49194 ай бұрын
Hi. How to test the pvc valve for that engine??
@robertfakinos38614 ай бұрын
Used this today and definitely helped me avoid a lot of hassles.
@DavidJWarEagle4 ай бұрын
That’s great news. Glad you got the job done!
@leemacklin29484 ай бұрын
Good video! Just lay under my hotrod tonight with your video and did the same thing. Videos like this are a life saver as getting the parts and instruction in Ireland can be a nightmare sometimes. I made sure to remember to wear goggles and the gushing ATF. I let the housing out slowly to drip into a catch can 😂 Thanks again for the upload!
@DavidJWarEagle4 ай бұрын
Glad you were able to use the video to get the job done! Hope you didn’t make as much of a mess as I did.
@kyleglover23534 ай бұрын
What mistake did you make with the bolts on the back valve cover gasket bc I’m about to change my valve cover gaskets and I don’t wanna make the mistake you’re saying you made.
@DavidJWarEagle4 ай бұрын
Hi Kyle, what is the timestamp for the part you’re asking about?
@brittmorries36955 ай бұрын
Thanks Brother, super helpful and detailed video. 2014 Chrysler 300S... Tried dislodging the "Devil Clip" without removing the alternator, no bueno/ waste of time. Ended up loosing all three bolts from the alternator, left one of the bottom bolts still attached and just tilting the alternator gave plenty of room. The alternator bolt where David used the combo 4X4&Jack to loosen it. You can actually put your wrench on the bolt and then pull from above with plenty of room and leverage (took me awhile to figure that out).
@DavidJWarEagle5 ай бұрын
Thank you for the tip! Glad to know that the video helped you get your Hemi repaired.
@markrichie8975 ай бұрын
thank you for making this video. The only thing that I would like to say is a low voltage transformer does not have a positive and negative. Look at the plug it is not polarized. Thanks
@DavidJWarEagle5 ай бұрын
Thanks for the info. Glad the video was helpful for you.
@badlilstang6 ай бұрын
What kills me is it's been 5 years since he has updated anything..he does a great job...
@badlilstang6 ай бұрын
Thank you so much!!!!!... people.. do NOT fast fwd the video lol. I forgot to tighten the SINGLE 10mm bolt into the previous plastic piece... I was able to grab it from the back side but it took some work and eventually got fully tightened. This video is perfect. The only thing I can say is he is a little to careful on drilling out the old plastic pieces to separate. I did it in to seconds wtih a larger bit.. opening up that hole means nothing so just drill them right out in seconds... other than that this video is PERFECT!.... ONE last thing.. I got my two liners as a KIT... do NOT buy from dealer.. they charge almost 400$ for shipping... blew my mind! I got it all send 178$ shipped with extra screws and clips for both sides... this video is 5 years old... prices have changed!.. THank you David!!!!
@DavidJWarEagle5 ай бұрын
Thank you for the kind words and advice. I’m glad the video helped you get your truck fixed up!
@gvoid6 ай бұрын
Bruh just replace the socket
@joeortiz74087 ай бұрын
Thanks
@DavidJWarEagle7 ай бұрын
You’re welcome
@kevinboyd29868 ай бұрын
Thanks for a great video!
@DavidJWarEagle8 ай бұрын
You are welcome! Thank you for watching.
@kevindove37788 ай бұрын
How many miles on engine when you needed to replace valve cover gaskets.... Also did you happen to know about what a repair garage would charge on labor.... Great video
@DavidJWarEagle8 ай бұрын
I’m not sure what a repair shop would charge but this engine had about 125K miles, if memory serves me. Thanks for the question!
@calvinbell328 ай бұрын
You didn't change the cam seal on either head? 🤔💭💡
@DiyAllaroundguy8 ай бұрын
the rear cover video has 3x more views than the front cover vid ... i wonder why lol
@DavidJWarEagle8 ай бұрын
Ha-ha! Some say he’s still removing the rear valve cover to this day.
@CorneliusSmalleliterealtor10 ай бұрын
I have the 2013 and just replaced the wiring harness and the entire light assembly a short in the wiring and the oem bulbs are so hot they have melted the housing.
@ForgivenFlipper10 ай бұрын
Perfect.. thanks!
@dianeprice115310 ай бұрын
I had no idea what that was on my 06 Dodge Charger V8 5.7 Hemi wow now I know
@ajsalazar8210 ай бұрын
I had to drop the alt
@user-hg3dj7ek8s10 ай бұрын
Is there a way to program two remotes to it? Trying to have a remote in my car and my wife's car.
@DavidJWarEagle10 ай бұрын
As far as I know you can program multiple remotes and you would follow the same pairing process with the additional remote.
@crimmie11410 ай бұрын
is it normal for both hoses with the green tab to have alot of oil in them?
@DavidJWarEagle10 ай бұрын
Yes, this is normal because the positive crankcase ventilation (PCV) system is pulling oil vapors out of the crankcase and into the intake. The inside of the intake manifold will be oily also for this reason.
@crimmie11410 ай бұрын
@@DavidJWarEagle im getting codes for p0351 circuit and it missfires, i changed the vct the camshaft position sensors and the crank shaft sensor Is it a wiring problem? because i found one that was exposed?
@crimmie11410 ай бұрын
there was oil in my pcv valve?
@jamesanelle58610 ай бұрын
Should just push in. Aftermarket repair parts quality is poor
@DavidJWarEagle10 ай бұрын
I agree on that. I think I’m going to try another switch and see if it is better.
@dougn235010 ай бұрын
This generation Sonata is notorious for going thru standard taillight bulbs. LEDs are the way to go on 2011 thru 2019 Sonatas.
@JSKZG11 ай бұрын
Do these bulbs fit into the same socket as the factory bulbs (2357's) or does it need a different housing? Asking b/c I just watched another video before I found this one and the guy said something about a new housing?
@DavidJWarEagle11 ай бұрын
The base of the 2357 bulb is the same as the 1157 bulb. There was an OEM LED tail lamp housing as far as I know, and that is probably what you saw in the other video. This video is a retrofit to replace the incandescent 2357 bulbs with LED 1157 bulbs and the bulb bases are the same.
@JSKZG11 ай бұрын
@@DavidJWarEagle Life saver. My daughter's Sonata bulbs keep going out and this is even after we got the whole back light panel replaced (mechanic thought that was the issue). She has 3 bulbs out now...they go out at once it seems....do all the lights in the back take the same size bulb do you know?
@DavidJWarEagle11 ай бұрын
@JSKZG I’m not sure on that but you can probably do an internet search by year/make/model to find out what the other bulb types are. I think the other bulbs are different but I don’t know for sure.
@gforce934211 ай бұрын
Thanks very much. Another video a guy was melting that post off instead of just moving it.
@DavidJWarEagle11 ай бұрын
You’re welcome. It’s not intuitive but serves it’s purpose pretty well.
@ricklavoie484911 ай бұрын
How long does dealer charge for installation 1 hour ?
@9929kingfish11 ай бұрын
will this operated on two garage doors or do I need a second kit on the other door with corresponding opener?
@DavidJWarEagle11 ай бұрын
Each opener requires a dedicated kit. Hope that helps.
@9929kingfish11 ай бұрын
@@DavidJWarEagle it does thank you
@ZeldaACFan1711 ай бұрын
This carousel looks nice, but it looks like the animals don't move up and down 😞 The up and down motion of the animals is my favorite part of riding carousels, but without it, the ride doesn't feel as fun 😢
@thevaultdoors Жыл бұрын
28:55 Removing the back valve cover what a 100% pain, until it wasn't. The cheat code.....evacuate the coolant lines and disconnect them. You valve covers will slide on and off as easy as the fronts do.
@GMZee559 Жыл бұрын
Did u fix the leak ❓❓
@DavidJWarEagle Жыл бұрын
Yep, sure did.
@jfc2103 Жыл бұрын
Yo, have you ever had to replace a purge valve on this car? I have an 07 3.0 ford fusion that has evap leak codes.
@DavidJWarEagle Жыл бұрын
Nope, I haven’t done that on this car.
@jeffh2125 Жыл бұрын
I have a 2008 Magnum R/T RWD and wondering if all new brake components behave such that one needs to push the brake down fairly far before braking occurs. I had hoped that I'd have a lighter touch required once all components were replaced. It is smoother for sure and not shimmy up front when stopping now. But the peddle feel is not like my wife's Nissan Altima for example where if I push slightly too much the whole car jolts to a stop. I just don't know what magnum brakes should feel like when there's new calipers, rotors and pads installed. I'm curious if the abs, or booster or master cylinder might need replacing.
@DavidJWarEagle Жыл бұрын
I can’t say for sure but I think my Magnum is the same way. Although, I need to clean and regrease the caliper pins as the pedal is a bit stiff currently.
@jeffh2125 Жыл бұрын
I ended up bleeding the brakes myself including getting a scanner to bleed the ABS system. It's stronger now and easier to brake. It still won't jolt to a stop like my wife's car, but It's much better. Thanks for your input. The scanner I got is a Foxwell NT710 if interested.
@DavidJWarEagle Жыл бұрын
You’re welcome. I’ll check out that scanner, thanks.
@Chipotlespice Жыл бұрын
Who the hell designed this POS. That rear cover is such a pain.
@HowManyEggs93 Жыл бұрын
I got the gasket kit from felpro. The spark plug tube seals were fine but the gasket lacked the curves for 3 bolt holes for the rear cover. Gasket didn't fit. 4 other brands on Rock Auto had the same issue. Just stick with OEM ford parts folks