Brent, what is the thickness of the film you use please? I have tried your method of sealing edges by leaving enough to go around edge of panel and heat and stick, but it seams not to work and wondered if the film I am using is a little thicker. It is 7.1mil.
@rteixeiraa115 сағат бұрын
Is that Stek?
@NancyDell-m6y18 сағат бұрын
Garcia David Lopez Michael Walker Mark
@EncorePPFtint17 сағат бұрын
Is that what it looks like when you tag some one in the comments?
@timh588721 сағат бұрын
kzbin.info/www/bejne/b6jZYZqhd8-katU
@timh588721 сағат бұрын
kzbin.info/www/bejne/n6m9aGd6npWrqtE
@donovanchick8336Күн бұрын
Instead of wax, why not try install gel?
@EncorePPFtint23 сағат бұрын
This is going to sound crazy but I've never tried gel. 🤯🤦🏻♂️ It looked messy. 🤣 What brand would you recommend? I have a Porsche Macon coming in for PPF in a week. I get a ton of pretacking on these hoods because of all the stretching and time needed for working areas down. Do you think that gel would be a game changer on a huge hood like that?
@donovanchick833623 сағат бұрын
@@EncorePPFtint absolutely. I wouldn’t use it on the entire thing but I like to use it on ridges just to keep the pre tacking to a minimum. Using it for the whole install would just make a mess. Any install gel should be fine, they’re all basically the same thing imo but if I had to recommend any of them CarPro has some and 3M has some.
@EncorePPFtint23 сағат бұрын
I'm going to buy some Monday so I'll have it ready. Might even test it on a different hood. It sounds like you are saying to apply it (full strength?) directly to the areas I'm going to get pretacking. Is that correct? I love learning new things. Thank you for bringing this up! Maybe someone has a video on how to use gel. 🤔
@donovanchick833617 сағат бұрын
@@EncorePPFtint exactly. I usually just squeeze a line along the high points and give it a good rub around with my finger to spread it out a bit. If I have a pretty tricky bumper like most Toyotas I tend to use gel over slip just because you get probably triple the dwell time before you start dealing with tacking anywhere.
@qairo-iwnlКүн бұрын
Does this prevent the roof from yellowing?
@EncorePPFtint17 сағат бұрын
Yes, it definitely should. It does the same for headlights.
@larryp85Күн бұрын
great video. how much ppf do you think it would take to cover the whole car? any brand ppf you recommend?
@EncorePPFtintКүн бұрын
Thank you. I can get you some square feet numbers on Monday. We use CovrGard PPF. It's a great material to work with. I can get you some pricing. Reach out to us at [email protected] 👍🏻😁
@larryp85Сағат бұрын
@@EncorePPFtint thank you
@hwkwkHsjSkl2 күн бұрын
Williams Cynthia Martin Gary Thompson Melissa
@nolanthewrapper2 күн бұрын
Love your videos excellent job as always thanks for your contribution to the industry
@EncorePPFtintКүн бұрын
Thank you! Whether it's a customer, beginner, DlYer, or a veteran installer. I hope people can find these videos helpful and resourceful. I know that when I watch other installers, I learn things. A new technique or tool. Even small things can make a difference. How long have you been wrapping?
@nolanthewrapperКүн бұрын
@EncorePPFtint absolutely your videos are helping me learn ppf much better that's forsure
@gameb0y862 күн бұрын
Is that an E30 BMW in the background? What are you doing to that one? Need videos on it!
@EncorePPFtint2 күн бұрын
It's so funny that you saw it there! It is an E30, and videos are being edited now. I PPFed the full front end. So, bumper, fenders, and hood videos are all in the works! With recording and editing, I'm going to have 15 hours just into the bumper video. 🤦🏻♂️🤣😂
@EncorePPFtint2 күн бұрын
It's a 1988 BMW M3 E30.
@lonzoreigns4982 күн бұрын
I tack down the sides and create my H but everytime I start, the film decides to shrink towards the H making a C shape or a U shape and seems to want to keep going towards the corner or the edges
@EncorePPFtint2 күн бұрын
The film will be the hardest to shrink on the corners. That's where you will have the most fingers, and because one side is tacked down with the H pattern, it makes the film heat shrink differently than fingers that are out towards the middle. As far as the U shapes... those areas are either shrunk enough or too much. You need to push those out. Sometimes, when you push the U shapes out, they create fingers at the left and right of them. Then you shrink those fingers down. I need to record some footage of a person learning to tint windows and how to fix and avoid the problems.
@EncorePPFtint2 күн бұрын
You will see in the video that I do not allow U shapes in my heatshrink. As soon as one starts to show up, you need to push it out and correct it.
@ladymoet2 күн бұрын
What software are you using for the cutoff
@EncorePPFtint2 күн бұрын
I use CORE from Eastman. 👍🏻😁
@VillageVlog-nq4jr2 күн бұрын
Sir, I want to work in your showroom. Please give me a visa. My house is in India.😢
@VillageVlog-nq4jr3 күн бұрын
Sir, I have completed the paint protection work. Why do you need a labourer?😢😢
@RustuCetin-rc8iv3 күн бұрын
Hello master, can you give me the price of window film for Tucson 2020 model vehicle?
@EncorePPFtint3 күн бұрын
Are you looking for a pre-cut kit or to have it installed? Reach out to us at [email protected] 👍🏻
@legocowboys3 күн бұрын
You do Great videos. Nice close ups and angles and instructions . Thanks for posting
@EncorePPFtint3 күн бұрын
Thank you! 😁 I'll keep at it!
@legocowboys3 күн бұрын
Is that “rep approved” footwear?😂
@EncorePPFtint3 күн бұрын
Ordered directly from the OSHA website. 🤣😂
@a.autoarmor3 күн бұрын
I friggin' hate doing white 😂 Thanks for the great video as always. I'm doing a Sienna on Monday, gonna be bulking tho, but this helps me mentally prepare 🤯
@EncorePPFtint3 күн бұрын
Cough cough... maybe you are feeling sick on Monday! 😂🤣 it looks like a pretty interesting bulk job. You should make a video and post it! Lol, then I can see how it's done! 😁 What is it that you dislike about white? The fact that you can't see water under the ppf as well or that every tiny piece of lint stands out. White is better than black, though!
@andrewewen3 күн бұрын
Definitely every single piece of lint gets me. Black has it's issues but I still prefer over white. Maybe being a mobile service, never having a controlled environment, isn't such a great idea 🤔
@EncorePPFtint3 күн бұрын
@andrewewen Yeah, a controlled environment can make a difference. I've installed PPF and Tint on my parents' vehicles in their garage. They live out if state. But their garage is very clean and has AC. Fancy! I couldn't install PPF in my own garage, though! 🤣😂
@whoiswaynereynolds54574 күн бұрын
You made it look easy!
@EncorePPFtint3 күн бұрын
I do tend to do that. Decades of practice can do that. 😂🤣
@whoiswaynereynolds54574 күн бұрын
I ordered an extension chord on amazon that locks on to the plug so it doesn't come loose
@EncorePPFtint4 күн бұрын
Hmmm..... I like this idea. 👌🏻
@whoiswaynereynolds54574 күн бұрын
@EncorePPFtint the company was clear power but the cord I bought is not available on amazon right now. They have other cords with the lockable end. It's a switch you turn and it locks into the hole on one of the prongs of the male end and lights up to show connection.
@pleaseletitgo18184 күн бұрын
What Brand is this PPF?
@EncorePPFtint4 күн бұрын
In this video, I'm installing PremiumShield NextGen.
@golddetailingcentar4 күн бұрын
What is in the hand bottle and what is in the hose? Thanks
@EncorePPFtint4 күн бұрын
The h9se has my slip solution, and the spray bottle has my tack solution. Here is a link to a video that goes over my solutions and what is in them. 👍🏻😁 kzbin.info/www/bejne/rnjNn2WorM1gjZYsi=KotCgOeeAXc8GzrV
@diegojunco70804 күн бұрын
Hola buen día. Que material utilizas
@EncorePPFtint4 күн бұрын
We used PremiumShield NextGen during this installation. 👍🏻😁
@skdigitaldiaries20105 күн бұрын
Keep it up brother 👌
@EncorePPFtint3 күн бұрын
Will do! Keep watching 👌🏻😁
@NoBody-jo5rj5 күн бұрын
Can you install ppf on door handle?
@EncorePPFtint5 күн бұрын
Yes, I'll get on this. I dislike installing PPF on door handles, so I've never recorded it. 🤣😂 Lazy!
@NoBody-jo5rj4 күн бұрын
@@EncorePPFtint i wouldn’t blame you for being lazy sense i am lazy myself haha but i was wondering every time i go to a film protection shop i ask them to protect my car with ppf film and including the door handles but they refuse to do so
@EncorePPFtint3 күн бұрын
@NoBody-jo5rj It's because door handles suck to PPF. 😂🤣 We definitely do them, but they can be a challenge at times.
@gameb0y865 күн бұрын
Your tint and PPF videos are super helpful. Keep them coming! be sure to get a video of the 4runner PPF install if you ever get one in the shop!
@EncorePPFtint3 күн бұрын
Thank you for the feedback! 😁👍🏻 I might have to go search out a 4 runner. I can't remember the last one it did. I'll put that one on my list of vehicles to keep an eye out for. 👍🏻
@mikesanchez14286 күн бұрын
what ppf is that boss? thanks in advance...Dirty
@EncorePPFtint3 күн бұрын
Hey, I used PremiumShield in this video. What brand do you use?
@mikesanchez14286 күн бұрын
man....i really wanted to see over 100k views....that goes to show you...some don't want to learn the best ppf lays. amazing work, and i am glad i found you. i don't do quite as good, not even close...so i am learning the good good. thanks for sitting us pheasants down and letting us see the show....Dirty...
@EncorePPFtint6 күн бұрын
The channel keeps growing. Little by little, we'll get the hopefully! 😁 The channel is less than 2 years old. Thank you for all of the kind words, and I'm glad to hear that you are finding the videos helpful! Keep working with the PPF, and you'll get to my level. It just takes time. 👍🏻😁
@how_bout_it79677 күн бұрын
He made that look EASY 😂😂 dang man!
@EncorePPFtint6 күн бұрын
🤣😂 I tend to do that! It's definitely not an "easy" install! 😁
@prhapsisuppose7 күн бұрын
Really appreciate this video. Super helpful for the things you need to keep in mind and planning ahead for fingers etc. also surprised how you were able to do this whole bumper with 24". I always assume il need lots of hangover on the edges, and you just opened my eyes to what can sometimes be possible. (and cost me way less....) Thanks again for this, love your videos.
@EncorePPFtint7 күн бұрын
Hey! Thank you for taking the time to leave this comment. I appreciate it! It is super helpful to watch other installers to their job. There is so much stuff to pick up on throughout the whole process. Maybe a technique or a new tool. It's great to hear what you found helpful in the video! You can definitely cut it close on the roll size. But, better, bigger than not enough! 👍🏻😂
@whoiswaynereynolds54578 күн бұрын
Hey! Who said you could put that on my car😅
@EncorePPFtint7 күн бұрын
Well, you did, silly! I have a habit of only sticking to requested work. That way, I get paid at the end. 😁👍🏻
@dennyrivas14757 күн бұрын
What brand of ppf is this? Stek, ultrafit, Rayno?
@EncorePPFtint7 күн бұрын
The brand is CovrGard. Great stuff!
@kam1leon7 күн бұрын
Great content Brent! Thanks for sharing
@EncorePPFtint7 күн бұрын
Thank you! 😁👍🏻
@360detailing10 күн бұрын
Excellent work 👏🏻
@EncorePPFtint8 күн бұрын
Thank you! :)
@underfundedaddict380611 күн бұрын
I can't fkn do it. pisses me off.
@EncorePPFtint11 күн бұрын
We were all there! I used to lose my mind! After my third or fourth try, I'd throw all of my tools from my pouch all over the shop. 🤬 I didn't have anyone to help guide me, and I don't like failure. Keep at it and soak up info from youtube. What brand film are you working with? Some films are very hard to heat shrink. What state do you live in?
@underfundedaddict380611 күн бұрын
ezy do a 2019 back door window removal. Doing great things here. Subscribed
@EncorePPFtint8 күн бұрын
Great to hear. Welcome to the channel! :)
@underfundedaddict380611 күн бұрын
wasting so much money on film. But I try. Thanks for the work
@EncorePPFtint11 күн бұрын
The $ is just part of learning. There is an art to it. With any trade, there is going to be a learning curve. You'd probably really benefit from som hands on experience in a class. What state do you live in? Once you get it, you'll be in great shape. It does take time and patience. I know it can be super frustrating!
@prhapsisuppose11 күн бұрын
I am doing a similar mustang next week, customer really doesn't want that separate piece above the grill that you took care of. This one doesn't have stripes. Do you think its possible to do it one piece (I can do the lower splitter separate if need be, or would it just be a waste of time and material to attempt? It's with 3M 200 Gloss. Thanks man LOVE your videos!
@EncorePPFtint11 күн бұрын
Thank You!! I appreciate the feedback. I think this bumper is totally doable in one piece. It's a little tough because you need to make sure that you stretch the film enough from left to right for both the top and the middle of the bumper at the same time. This kits is just set up to make it very straight forward for the installer. This would be a pretty complicated kit if they didn't separate that top middle piece. Too close to bulking I'd guess.
@prhapsisuppose11 күн бұрын
@@EncorePPFtint Thanks for the response! I'm gonna just go for it and hope for the best. Keep up the great work
@alaaaleskandrany682211 күн бұрын
Thanks 🙏
@EncorePPFtint11 күн бұрын
No problem. 😁
@adamgen123612 күн бұрын
What brand of PPF do you use
@EncorePPFtint11 күн бұрын
This is NextGen by PremiumShield. 👍😁
@maysamsay465712 күн бұрын
Where’d you get that dash towel?
@EncorePPFtint11 күн бұрын
That is from www.dashprotector.com/ I've been using this dash protector for over a year now and I really like it. 👍
@user-zp4gf2kh9g13 күн бұрын
❤❤❤
@EncorePPFtint8 күн бұрын
👍👍👍
@senditsammy13 күн бұрын
Hey great work here man. I have a carbon roof on an M4 pretty much exact same roof. My carbon is yellowing and I had an idea to maybe get it tinted with window tint (dont think they make tinted ppf) instead of just clear ppf since it would darken the yellowing roof without needed me to get all the labor done to re clearcoat the roof. Any thoughts on this?
@EncorePPFtint13 күн бұрын
Thank you for the feedback! I just got done installing carbon fiber PPF on the hood and spoiler of a Porsche Panamera. This PPF looks amazing. I'll post a couple of pictures on the community board for this channel. As for the tint. Tint will not work. Window tint that is exposed to the elements will go bad super fast. Plus, there is the whole problem with heat shrinking and trying to get it to stick to the roof. It's all bad. You can definitely have vinyl installed over it. Vehicle wrap. You can pick any color or finish. They also have tinted vinyl. I'm not sure what sizes it comes in. Either way, you are going to need to make sure that the roof is very smooth. Otherwise, that bumpyness is going to show after the installation. It might need to be lightly wet sanded. Did you call around and get pricing on having the roof recleared? I'll ask the bosyshop that recleared this roof. I'd figure that vinyl is going to be your most cost-effective option. But you are probably looking at 3-5 years for the lifespan of vinyl on a roof. PPF will be 7-10 years.
@EncorePPFtint13 күн бұрын
Here is a link to the pictures. kzbin.infoUgkxDBSjgCD9WJQtyZbFEKIWttkfg0y51rBK?si=VHG9QgVEpzu7nhFu
@senditsammy12 күн бұрын
@@EncorePPFtint Yea i need to call around more for a quote on the clear coat. Currently turning the car into a full track car so not too concerned with looks. I am located in the bay area, so stockton is not too far if it can be a single day job for tinted vinyl or ppf. Definitely will contact you in the near future. Thanks
@didiermejia78013 күн бұрын
What!!!! I didn't get any notification about this video. I just ppf my civic type r and my Shelby GT350 is next.
@EncorePPFtint13 күн бұрын
Well, these videos should have you covered then! 😁👍🏻 How did the civic turn out? Let us know if you'd like a kit or some bulk material. 🤔
@didiermejia78013 күн бұрын
@EncorePPFtint I did a full ppf on the type r. I left the bumpers for last and they came out 8/10 on the rear and 7/10 in the front. The rest of the car solid 9/10. For sure, I'll look into ordering some bulk ppf from you guys, Thanks again for all your videos!
@ranadhirsinha163413 күн бұрын
I am interested this work sir and I am still searching for job😢
@EncorePPFtint8 күн бұрын
Where are you from?
@jamelcasinan826914 күн бұрын
sir, im ur follower, just a question, what's difficult, tint or ppf, I know how to tint, ppf, I'm just a beginner
@EncorePPFtint14 күн бұрын
I think PPF is harder to learn. As well as more expensive to get into and learn.
@dabeerahmad933114 күн бұрын
Hey Brent, I Was just wondering what brand is the Grey rag for drying. Does it leave micro lint behind? Thanks for all the videos love the content 🙏👍🏽
@EncorePPFtint14 күн бұрын
Hey! These towels were ordered from PremiumShield back when they sold towels. I'm pretty sure that we bought up the last few boxes a couple years ago. So, unfortunately I do not have an exact towel to link you to. 😢 The have loops on one side and are smother on the other side. They do not leave any lint behind. Great towels. I'll reach out to the manufacturer of PS and see if they remember where they got them. 👍🏻
@Hector-xt9vy15 күн бұрын
What type of plotter do you use? I’ve been installing only bulk PPF and I’m thinking in getting one. Thank you .
@EncorePPFtint14 күн бұрын
Kits are great. I don't always use them, but it's great to have the option. We use a 40" GCC Jaguar V and a 72" GCC Jaguar IV. All in all, they've been great plotter cutters. I've heard great things about Rolland and Graphtec plotter cutters but have never used them myself. 👍🏻