10 ай бұрын
Пікірлер
@Redneckfisherman06 2 күн бұрын
That’s a sweet deal it was free with a running Kawasaki instead of junky old kohler and it’s a cub cadet they have great transmissions or gearboxes
@philliphall5198 3 күн бұрын
Does everyone have a snow blower who has a house up north ???
@Lawnmowercare 3 күн бұрын
Probably not! Maybe you could send reinforcements!
@Orticai 4 күн бұрын
First start since last year?
@Lawnmowercare 4 күн бұрын
It was in a barn we pressure washed it. Also We put new gas fuel line and a carb on it. Funny comment though.
@mariajeunhomme9356 18 күн бұрын
THANKS, perfect et magnifique pour mois.
@paul-u9j3k 22 күн бұрын
Thanks for the video. I purchased one and there is virtually no videos for maintenance, other than an oil change. I couldn't get my drain plug loose, so i had the dealership change oil, $165.00, still cant get drain plug to loosen, and i need to do another oil change. Good job!
@evetssnibbor Ай бұрын
You made my day! I couldn't figure out how the choke level worked!
@Lawnmowercare Ай бұрын
Thanks for commenting. I post things from time to time and some are helpful and some are not so I appreciate the feedback!
@One44Special Ай бұрын
You're right there's no videos out here for the bison 400. So thanks for doing this one. I was getting no error code. But the light for the shift position was staying on and it was flickering.Bright dim almost like a turn signal. Also, my fuel pump would come on for 5 seconds.Go off for about ten and keep cycling like that Until I disconnected the battery. Today I hooked it up to start it and when I Started it the starter didn't disengage. Now I have a code: P0351. So i'm thinking I have the same problem.
@Lawnmowercare Ай бұрын
I always try to start with the most affordable options that could fix issues. Solenoid under $12.
@Lawnmowercare Ай бұрын
I had to disconnect the battery because the starter would not shut off. Originally you could just touch the disconnected cable to the battery and you could get it to start but as soon as you remove the cable, the engine shuts off. That’s why I tackled the solenoid!
@Lawnmowercare 22 күн бұрын
Did you figure out your issue? Was it the same problem?
@speckhunter84 17 күн бұрын
Where did you get the solenoid at? Also part #? Mines doing the exact same thing any info is much appreciated thanks
@Lawnmowercare 17 күн бұрын
@@speckhunter84 a.co/d/iGQ1XYQ
@ZzZ-f3q Ай бұрын
Working on a ch25s 68704 with almost excessive endplay. Is there a bearing at all for that end of the crank shaft you popped out, or does the crank just ride in there with its seal?
@BrandonDunlap-i1x Ай бұрын
Thanks for the video. 91301-Z9L-000 - O-Ring (19.1X2.2) - Honda Original Part. I bought an o-ring that was a bit wider 19mm inner diameter by 2.5mm width. The wider o-ring is working great.
@Gilda1054 2 ай бұрын
Just what I needed as having problems with choke!!
@harmonysprogress 2 ай бұрын
Can I use my electric impact drill to remove the bolt??
@Lawnmowercare 2 ай бұрын
Sometimes they are not strong enough
@harmonysprogress 2 ай бұрын
@Lawnmowercare it worked!!! 🤠🤠🤠
@edge2sword186 2 ай бұрын
Thanks . Looks like the ring gear split but I have another flywheel in good shape.
@SmallEnginesFan2010 2 ай бұрын
Thats a nice engine
@marianovargas9890 2 ай бұрын
Where could I get that switch ?
@Lawnmowercare 2 ай бұрын
eBay Proline Decompression Valve For Hilti DSH 700 DSH 900 DSH 700X DSH 900X 261965
@HectorGutierrez-ml6jo 2 ай бұрын
Awesome video your a big help keep up the good work 😊
@ggaguar4963 2 ай бұрын
Having the same problem on my 2015 T3000 24 HP same linkage as this video ,you would think they would put the better white plastic little square slide for the cable to slide as needed for Slow -to- Fast -to- CHOKE.... ,keeps bending cable, so i think like you did pull the cable as much as you can & tighten with a T-25 on a socket wrench ,. this video should do the trick to solve this simple stupid mickey mouse Linkage . - Thank you -
@EliaCashen 2 ай бұрын
Thank you for such a short, to the point, video. Just saved me a bunch of time watching all these other guys fluffing the videos with useless commentary mostly unrelated to the title. Good job!
@chrisyoung8759 2 ай бұрын
Is it possible to buy the little plastic piece on that bracket you show in the very beginning?
@michaelczaja9267 2 ай бұрын
This saved me more aggravation than you could possibly imagine!!! Thanks so much.
@roccophipps2771 2 ай бұрын
Thank you very much! You helped me solve my issue.
@jeffspoelder7966 2 ай бұрын
it helped ty
@jeffspoelder7966 2 ай бұрын
ty
@slidelltowne183 2 ай бұрын
Got one $409 from LOWES, new, year 2k. Made in the USA and it shows...motor runs good but slapped on seals and assembly. Now looking for front valve cover seal and noticed oil weeping in same location as yours. Ist one went back to Lowes due to faulty under deck construction..small twigs get jammed under plastic to metal under deck, bulging plastic down till the blade strikes. We all got that issue that is just piss poor engineering. Somebody posted that flaw here on YTube. If the layer laps were reversed.. then NO problem. Has not done that on second mower..yet. Got 11 year old Chondas with no issues!
@Lawnmowercare 2 ай бұрын
Thanks for sharing your experience
@slidelltowne183 2 ай бұрын
I have a collection of SAE o-rings and replaced with one slightly bigger cross section. The OEM O-RING (19.1X2.2) is NOT sized right from the factory, mine was perfect, no cuts, flat spots, ect. The steel valve cover is priced at $44 so be gentle poping that thing off! Why Honda used Honda Bond is pure stupidity for those who simply want to adjust your valve clearance? I used Permatex grey, local, but takes 24 hour cure unless you pay more for the 90 minute stuff. Went over and hugged my GX200 and GX390...
@juan06031993 3 ай бұрын
How do I know if my pulleys are good?
@Lawnmowercare 2 ай бұрын
Pull the pulley brake back and spin it. If they spin smooth great. If you hear or feel rough sound then it’s bad. Another way turn on blades and bearing sound will be loud on either to both sides. Good luck!
@JulieMcClure-w2p 3 ай бұрын
Thank you thank you, exactly what I needed!
@BZRKBUDDERMAN360 3 ай бұрын
Would this also apply for a Lowe’s 5x8 trailer?
@Lawnmowercare 3 ай бұрын
@@BZRKBUDDERMAN360 the axles only rated for 2000 to 2500 pounds. think about getting a 3500 pound axle save up that little extra money and get a better trailer. You’ll thank me later.
@Lawnmowercare 3 ай бұрын
Better yet save you up a little more than that and get a 6 x 12 or 7 x 14 you’ll never have to make another Trailer upgrade again. If you’re ATVs, or want to haul 2 mowers thank me later.
@BZRKBUDDERMAN360 3 ай бұрын
@@Lawnmowercare all I’ll be towing is a motorcycle and a couple tools for it. Are you sure 2000 isn’t more than enough?
@BZRKBUDDERMAN360 3 ай бұрын
@@Lawnmowercare I’ll be towing it with my station wagon, the car is rated for 4500 lbs but the aftermarket trailer hitch only takes 2500
@angelicasantos1828 3 ай бұрын
42 "?
@angelicasantos1828 3 ай бұрын
42"
@shannonbrooks8834 3 ай бұрын
How bout dummy flips for tractors?
@vincentquattrocchi7924 3 ай бұрын
Hi, need a Carburetor for a 20yr old Briggs and stratton 15.5 IC OHV Craftsman RIDING MOWER.... Could you tell me which one fits?I would greatly appreciate it.....THANKS!
@ricksilverado8974 3 ай бұрын
THANK YOU that spring has been making me crazy on how it gos. great video.
@A.Edwardson 3 ай бұрын
Stevie Wonder must be doing quality control for Honda.
@bustersmith5569 3 ай бұрын
180 dollars at the dealer,,,,
@danoverton4297 3 ай бұрын
Great video. Thanks.
@nanscott3092 4 ай бұрын
Very informative, thank you
@angelamatemotja 4 ай бұрын
Thank you so much!
@bwspacity 4 ай бұрын
I have a 2460 magnum.my batt wire from ignition to regulator always has 12.56 volts.even with key off.is my key ignition bad?when running that wire has 14.9v
@Lawnmowercare 4 ай бұрын
@@bwspacity most likely. Start with the cheapest items first.
@rickeykeeton4770 4 ай бұрын
I have one that sometimes has to be put I forward gear then reverse for it to back up. I put new belt on it. Did not solve the problem. Sometimes a little jerky in forward too. Maybe I need to relocate spring just a little? I think the Holly’s are good. None broken like that one anyway. Bought the belt from a small engine parts shop/store. Maybe not oem, not sure.
@thyubernoob 4 ай бұрын
I bought a KIPA carb off Amazon for my B&S 14.5hp rider for $20...been running great for the last 2 years.
@frankpagano9947 4 ай бұрын
Terrible video
@cameronikels4831 4 ай бұрын
Mine has the exact same problem!
@wolfhavengardens 4 ай бұрын
Very hard to find any videos or pictures on this rare mower. Great job. Thank you!
@BrianHarvey-e3e 4 ай бұрын
Very well done. When I got the tractor from a friend with a new card to install the choke arm was just dangling and I could not figure out where it went this was a huge help.
@Lawnmowercare 4 ай бұрын
@@BrianHarvey-e3e glad the video helped! I figured somebody out there might need it one day.
@joseberlanga4400 4 ай бұрын
Gracias
@stormgsi911 4 ай бұрын
I welded my bolt to a plate so I could get 2 c clamps on either side. but she worked.
@khsrio621 4 ай бұрын
Got a used Ariens (same model) for $75 all that was missing was one part from the throttle linkage. Thank you for saving me from hours of confusion!
@dennislanning9924 4 ай бұрын
This video was so good and it helped me with exactly what I’m working on. Thank you.
@christiankendall8875 5 ай бұрын
I have a Dixie with no click no start. Pull the PTO up and down 15-20 times, it may start. Feel like that’s the issue. Is it easy to replace?
@Lawnmowercare 5 ай бұрын
Yes sir just buy a new switch and you’ll be in good shape it sounds like. Just be careful, removing the hardware as you don’t want to lose anything.
@wesleyrice526 5 ай бұрын
What size wire did you run from your solenoid to the starter? Also what size wire to you recommend for wiring rest?
@Lawnmowercare 5 ай бұрын
12 gauge if you can
@huntcain8636 5 ай бұрын
What if you have a ground going to the ignition coil? Thanks
@Lawnmowercare 5 ай бұрын
Ok