How do you get the lights to stay the same. Mine always reverts to orange when you turn the car off.

Thanks for the video - just one comment the trunk features you showed requires the power trunk feature otherwise it’s just remote open for the trunk. No automatic close.

Incomplete. How about the wrongly installed plugs and receptacles? Disappointed.

just subscribed, this is hand dow the best x1 18i review on YT. Ive see them all since i Might be buying one lol

Why is nobody testing any S/FTP cables with this tester? Lame. The G is fake on mine. There is not even a LED soldered on the PCB.

Can this be used on a patch panel in a server room to the office wall port or would it cause damage?

It’s been more than two years and you never did the next video that you promised that you were going to do on how to set up this router 😢wow

Una bellesa 🔥

On 2:03 Can you please tell me what is that yellow plastic used for? Do I need to clean it ,looks like drain plastic or sth like that Tnx a lot

Hi @shaun, Would this method still work if I have to test ethernet cable that had the wall jack on one end and rj45 connector on other side?

Best explanation ever !

It doesn't hurts?

Complete and comprehensive review. Plan to look for a BMW X1 sDrive18i SUV (F48). With 1.5 litre engine will reduce the road tax cost and fuel. Is is natural for 3 cylinder petrol engine to sound a little like diesel engine. Hope to own one for town, city and long distance drive.

Thankyou.. this is a were detailed and well explained video A++++!!!

I had one cable run where no lights 1-8 illuminated at the masters side. What’s going on ?

Well explained. I didn't know we can use the tested to test connectivity of the connection in the wall, i thought its only used for "in hand" cable testing. Nice video!

For tip 1. Please don’t do this. Not unless you want the drainage to block and rain water come in to the cabin via the vents 😑 The locking mechanism to remove the plastic on the g20 models are designed to allow access to remove debris, not store food 😅

Thanks for the demo. Very informative. It helped me.

Hi!how can I test the port of my Lan card integrated on motherboard?The pc don't have any operating system.Thank you!

All contained ib drivers handbook, if you deign to read it.

It seems it is possible that the continuity test passes and the cable still can’t carry traffic. If the cable was installed 10 years ago, might it have developed defects by now? This cable is over 70 feet long from the router to the den and is not easy to rewire as diy job.

Pressing and holding the down arrow for the fam turns off AC

Flawed demonstration. You proved continuity but you did not demonstrate what the tool displays when you don't have continuity. Because you happened to know that the LV port in the patch panel connects to the Ethernet jack in the living room, you demonstrated that main and remote units light up all 8 LEDs. But when you moved the main unit to the R1 jack in the patch panel, you should have shown us what the main unit and remote unit still plugged into the living room jack display at this point when there is no continuity. Instead, you rushed off and yanked the remove unit out of the living room port before we could see its LEDs and then you just repeated the SAME DEMONSTRATION, this time with R1 and the first bedroom. The whole idea of testing continuity is when you don't know which jack in a room connects to which jack in a patch panel and you are trying to figure this out. Your video did not help me answer this question.

Hi Shaun, thank you for the walkthrough. I just recently got my flat and was looking into ways to test the RJ45 ports in the house. Thanks to your video i got some clarifications. Can I check with you, do you happen to chance upon people who uses a LAN switch port in the DB box to split from 1 router port to the various room? Does it reflect the same SSID by doing so?

This video was absolutely perfect. Thank you!

What does it mean when The ethernet tester number light goes reverse from 8 to 1 ?

I am using this same unit to test the wiring in a building. I notice on a lot of connections 1 doesn't light up, 2 lights up faint, and S doesn't light up on quite a few connections. I then checked both ends and they are crimped / patched properly and the connection works when I connect a laptop. What do you think is going on there?

Thanks for doing this video, it's really helpful!

What was your timing?

Interesting to see the Singapore versions for BMW. Good job! I enjoyed watching. BTW- I like your video title: The Good, The Bad.... (but no Ugly)...because BMWs can never be ugly. 😂 I have a 328i and I’m a long time BMW fan.

Shaun... Excellent video, well done. I have one question... is there a way to test signal strength from the gateway to the end of the cable? I have a couple of 75' ethernet cable runs, one to a gigabit switch and one which will go to a Eero 6+ mesh module that will be set up as a bridge?

Needed to understand that S state. Thank you a lot.

where is the cruise control? how to do it?

Hello , are the light ( ambient light) also in the rear seat doors? Or there are only in the front seats doors?

Why do you need to turn if off? Leave on 21/22° all year. People don’t understand how AC works ( especially my mrs) Gets in the car when it’s freezing out and cranks it up to high etc

Thank yoy

subscribe done! great review

Nice Shaun. Thanks mate.

Nice sir

hello shaun thanks for your instruction video. I have measured a CAT7 cable through a wall socket, but the test box does not give a chronological signal from 1 to 8, but goes from 1 to 7 and back to five. How can I check whether the problem is with the connection in the wall socket or whether the problem is with the connector of the Cat 7 cable?

Nice vid thanks!

Great VIDEO

perfect place to hide my weed!!

Nice vidéo ! Is it possible to fold the rear seats?

good video can you check the home phone line the same way

is there a way to put google maps (apple) in the central instrument cluster?

Just bought a cat6 cable and my modem and computer only negotiates 100mbps. The store I bought it from say that there’s nothing wrong with it. I had made to a specific length and now they don’t want to swap it.

The BMW system was designed to be left turned on (snowflake symbol illuminated) 365 days a year, and NEVER turned off. The IKHA system is designed so that all incoming air first gets cooled (even in sub-zero temps) which removes the moisture. Once the air is dried, the system then warms the air to maintain the desired cabin temperature

Agree, it’s not only annoying but actually dangerous. If you are using apple carplay you have to press 5 buttons to turn on the ac then get the screen back to where it was. Very dangerous if you’re a shit driver. How hard is it to just put an ac button on the dash?