Great job, the little one in the top drawer was funny bits
@HowdedodaАй бұрын
Great ideas. Do you have the file or video on how to make the cardboard box for the glasses?
@craigfyvie6668Ай бұрын
I’ve now built the frame and installed the drawer runners(same ones as you). They are really stiff because of the black stopper catch on the runner. Do these come off?
@NeilLovegrovemakerАй бұрын
I didn't have the same problem with the stopper so not sure if it comes off.. are they stiff without the drawer attached? If not it's likely that they aren't running parallel so are fighting against each other
@craigfyvie6668Ай бұрын
They were really stiff without anything done. Straight out the wrapping they were stiff.
@NeilLovegrovemakerАй бұрын
That doesn't sound right but it's difficult to know without seeing! Mine didn't have that issue. Unless there's an obvious thing that they've got to stop them sliding open in transit id suggest contacting the manufacturer.
@feelosophy19212 ай бұрын
Cool
@Flipping_Assets2 ай бұрын
Use epoxy as filler.
@Flipping_Assets2 ай бұрын
How do you freehand drill straight?
@Symek922 ай бұрын
I seen a few videos about the storage under the stairs and I must say this is the best one I have seen! Well done!
@ethantyler45962 ай бұрын
Do you have any advice for removing the brackets? We have the same for our floating shelves, but right now are moving house, and are really struggling to take them out the wall 😢
@NeilLovegrovemaker2 ай бұрын
I've not had to take mine off yet. I'd probably start with trying to pry out from behind the shelf, or fitting a clamp to the shelf that can be gripped better
@leemarsden18462 ай бұрын
Can you send me the details of the latch and also the sliding closures please going to do this my self too
@davidreynolds30823 ай бұрын
Imagine leaving that particular drawer sticking out accidentally and one of your children walking face-first into that very sharp angled corner! That's dangerous and an eyeball gone for sure.
@NeilLovegrovemaker3 ай бұрын
No injuries so far! 🤞
@jameshenderson53853 ай бұрын
Whoa! Narely knots!
@marknorris93823 ай бұрын
Pretty cool got to make some for my sister in laws wedding
@tbonetone003 ай бұрын
Great vid. Just one thing is confusing me. When you transferred the stairs angle to the table saw, the sled angle is not the same in the next scene when you start cutting? Really confusing me how you've set the angle on the saw?
@vassabatielos47403 ай бұрын
Wood filler not poly filler
@benben-du1fc4 ай бұрын
só
@buddydog19564 ай бұрын
Well, that setup is only as good as the wall material - in your case, you have a solid wall.....now, if you have sheerock - that setup ain't gonna work ~ I'm outta here ....
@lordmandalor4 ай бұрын
WHAT, buy 3 lag10" should work, drive bolts into you studs in a line. cut the heads off, drill same size bolt hole in wood, aligned with bolts, put shelf on. done.
@user-ei9pf8cz3o5 ай бұрын
Hi it’s Russian cherry or premium and it’s better with 3/4 or 5/8 will be good?
@NeilLovegrovemaker5 ай бұрын
I used 18mm which is 3/4 equivalent. It was sold as "hard wood"!
@craigfyvie66685 ай бұрын
Could you please post a link for the drawer sliders. I’ve looked for a set and these look by far the best kind.
@arsecheese515 ай бұрын
The problem with the drilling is you didn’t seem to use a drill with hammer action. This is the reason it all heated up last time and didn’t work, and ruined the carpet. The hammer action will make light work of drilling into that wall. Also, if you did need to remove that shelf just get a Jimmy bar down behind it and it will easily ‘lever’ off the wall. More force than trying to tug on the shelf. Good luck.
@ahmadhasan32585 ай бұрын
great video, audio levels are a bit of a mess but your personality kept me going thro the video! great job!
@mirianmendez15 ай бұрын
Now how do you remove it I’m trying to take mine down
@robinalexandermusic22656 ай бұрын
What is the size of the wood?
@dennishrcka58846 ай бұрын
Did you drill into a stud? Or is that not necessary?
@NeilLovegrovemaker6 ай бұрын
For my wall it was a brick wall so didn't have any studs. There are some third party plug options out there if you can't align with a stud
@dadydadydady66526 ай бұрын
Well done
@marchandford77876 ай бұрын
Just wanted to say thank you. I have been trying to figure out how people make the runners soft close. Now I know thank you. Love the work.
@DanielTownend6 ай бұрын
Hi Neil, do you have a video for that table saw jig? I've just bought the same table saw and would be really useful to have.
@NeilLovegrovemaker6 ай бұрын
No I don't I'm afraid!
@angelamcclanahan21436 ай бұрын
SO IMPRESSIVE ❤❤❤
@davesmith98447 ай бұрын
Are you using an SDS drill or a combi drill?
@NeilLovegrovemaker7 ай бұрын
It's not SDS but it's a mains powered hammer drill with a conventional chuck
@davesmith98447 ай бұрын
@@NeilLovegrovemaker You'll never go back once you try an SDS drill :) Amazing. Especially for concreate or very tough bricks.
@vstringer437 ай бұрын
did you put your holes into studs? or just your drywall?
@NeilLovegrovemaker7 ай бұрын
Neither. This is a brick wall
@neelamsanga39807 ай бұрын
What is the weight of your shelf ? I have a live edge messmate timber- 1500x400 mm. I want to put it up as a floating shelf but it’s quite heavy and I am looking for some heavy duty brackets. It would be nice if you could let me know how many kilos these brackets can hold. TIA
@NeilLovegrovemaker7 ай бұрын
I don't have that info in afraid. The good thing with them is that if it needs extra support you can remove the shelf and add more studs for strength without removing what you've already installed
@martycarr15327 ай бұрын
What size bits ??
@kulkulan2237 ай бұрын
Why is it still wobbly though?
@rjtwo54347 ай бұрын
Wow an actual diy video where the person doing the work doesn’t have a full woodshop! Thanks for doing this video. The results are fantastic. Quick question for you; are you using the full paid version of sketchup? I just started learning it and it’s great to draw up the plan first.
@peegee99318 ай бұрын
I've found the very best way to fix a floating shelf that will be rock solid is to use 12mm threaded rod and fix in the wall with resin, making the hole in the wall 16mm. Just support it for 15 mins. The down side is that it's permanent but most shelves are. I've done many like that and they hold any weight.
@2njenn48 ай бұрын
Can these hold house plants?
@DennisDolan-fl3mw8 ай бұрын
very informative. never heard of those mounting screws
@michael.schuler8 ай бұрын
For thicker and stronger floating shelves (min. 1 3/4" thick), check out Hovr Bracket System. 300# load capacity at 8" shelf depth. We just used them for first time on a major kitchen renovation. Incredible product performs just as claimed.
@bilalrushdi25448 ай бұрын
what auto cad software did you use please
@karlswanson86749 ай бұрын
this video is perfect for what I need!! Well filmed and well explained....love the bedroom😂
@richardcranfield46209 ай бұрын
Bro why is someone who has so much nice sawing kit using a combi drill as a driver?! Awesome job though I hope mine turn out half as nice as yours!
@MrLaroygetz9 ай бұрын
Great Work👍
@missyt201110 ай бұрын
Came here because of the thumb nail 😂😂😂
@demonicxpriest769910 ай бұрын
I've got a void behind a stud wall in a old airing cupboard I've removed all the plaster and want to do something same as this and was racking my brains how to do it and your video has made me feel quite confident about doing this
@prestwichian10 ай бұрын
Hi great video, the link to the Amazon drawer runners, please can you tell me is it the 250mm or 350mm that are needed?
@APC990610 ай бұрын
Great video
@descalf10 ай бұрын
lol! I remember the day I first learned what a "spanner' was. 🤣
@lounar48211 ай бұрын
That bit you showed was a carbide tipped drill bit used in drilling CEMENT, not wood!!