Thanks for the best straight to the point walk thru.

What makes the compressor line form ice and then it fridge is forced in the defrost mode. The ice will fall off the copper line?

Only thing you missed was floating the seams on the underlayment so you can see the seams thru the vinyl. I’m a flooring contractor so I know this. Other than that, this is perfect

I don't use glue. Just clear silicone on the edges.

Those caliper bracket bolts are torqued to an insane torque spec from the factory. More than the ball joint torque specs!!

You kick the bumper, and the wife jumps out, opens the lift gate, puts the groceries in, gives you a beer, problem solved! I saw it in a video one time.

Thank you for the video 😊 can’t afford for anyone to put vinyl down for me so I’m going to do it by myself this video was extremely helpful. Thank you.

how much weight can joists hold. Would you say is safe to put plywood and used the attic for storage ? I fear I might break a joists and damage the structure of the house bringing the whole house down! Even walking on joist and beams freaks me out since I’m 220lbs I don’t wanna break essential beams or joists Any help if greatly appreciated New home owner! Thank you!

É serio??!!esse artista se benefia do trabalho das formigas e o unico trabalho dele é jogar o produto to no formigueiro,assassinar algumas formigas que estão próximas e depois de seco ,retira o projeto,lava e vende?????!!!!😤

Me putting a live worm on. He flys for the first time

I like how straightforward it was without a lot of talking and nonsense like here’s the part let me unpack it blah blah blah also, can I just not cut the power instead of having to pull the whole oven out and unplug it because that seems like a lot more work than shutting off the main breaker

What is this? A center for ants?

My LG 3 door fridge was not getting cold but the freezer was working fine. One technician came out and verified the fan was working but could not solve the issue. It ended up being a part in the drain line that was installed upside down in the factory that caused the drain line to freeze and plug up over time. Causing the issue. After a 5-minute repair it works fine. Of course the factory wanted $500 flat rate to come out and tried to claim that if it was a compressor that only the parts were under warranty when it clearly says in the manual that parts and labor are covered for 5 years. After I threatened to call my State attorney general an attorney they finally agreed to send a technician out without charging me the $500 up front. Like I said it was a 5-minute repair and a factory defect that the technician said he had seen four or five times. There's no way LG doesn't know about this yet they still try to get a $500 flat rate fee for a 5-minute repair up front.

It was the bits. I have 2 or 3 times now closed my tailgate with something sitting on the bumper and every time its gets "locked up" like this.

to ants, we are an incomprehensible eldrich horror.

Fuck

Nice thanks it helped open my Tahoe trunk 😊 it has never happened to me.. it does work 😊😊😊

Playing Nelly's song Hot in Here!

The Amazon ball bearings for a JD LA115 from DEEG do not fit on the spindle axle. What is the JD part # ?

Just an 88’ 185 hydro and it’s a beast. Thanks for the video, it’s has been extremely helpful

I have a Cub Cadet 1810

This part of laying out is wrong! You simply layout craft paper and cut it to the floor perfect fit. Now you have a perfect pattern.

AWESOME THANKS

Great instructions, thank you!

That's not right..

Thanks, we are trying to service few mowers at my dad‘s place and couldn’t find the oil drain plug. Once we found it silly we didn’t see it before.

thanks you!!!

i didn't see anyone mention the "THE TEXAN MODEL" made by the york nut sheller, works the same way, just one tool, less mess, leaves the 2 halves whole no broken off end bits, cost me 3.95. i found that soaking the whole nut for 8 hours or more helps. it also works just as good on other hard shell nuts 🙏

Was there some indication that the needle(specifically) needed to be replaced? or is this standard practice if you are tearing down the carburetor? I have a 2012 725 series B & G on a craftsman mower (has auto choke) Now that I'm retired I have the time to pay attention to stuff and it keeps me from thinking about ice cream.

What other tool can I use calibrate the caliber?

🔥🐜☠️

So I don't need to bleed the brake line ?

Shame on humanity

Thank you so much I needed this video you saved me money ❤

My cutter keeps sliding off the end. Won’t cut. I’m Missing something

Human are not good for environment

Amazing. I’m gonna save so much time and a bit of money too. Thanks for the extremely helpful content!

That’s cool af. Fire ants are nasty critters if near your house. This is innovative

Is it the same for both sides?

Thanks for the video! I have a code IF E, Ice fan either frozen or inop. Frig is not cold but freezer cold normal. I bought a Ice fan for the freezer compartment to get cold air to ice maker. Will this not get cold air to the frig then? Looks like I need the fan you just put in. Great video.

No help at all

Who the hell patches a floor that looks like that? Hopefully you’ve grown from this horrible content.

Ant abuse

Wonder how many are encased in it.

I tried this trick and it worked!

What you put before the vinyl?? Wood??I have nice wood floor in my room and I don’t want to damage it but I want to put vinyl floor on top because is easier to clean that’s why I’m asking because I see you nailed some kind of floor before the vinyl

just ordered one for 28x12 ovall, cant wait to install it, thanks

Thank you for making this video. Very helpful. Cheers big ears!

Song:♥️😘🌷 Video:💀❌😈

Finally a good video where I can see what’s is happening thank u boss man