I'm sure you'll learn how to make it if you'll read woodprix instructions from cover to cover :)

Adding the weight to the bar makes so much sense, as it will let the engine slowly break loose on it's own. Most of us have tried to force an engine to break loose with the starter or breaker bar, which often does more damage to the engine, especially if there are underlying issues which are not known....quite often the reason the vehicle was sitting for many years in the first place.

Outstanding thank you

It’s because I’ve always had questions that I’m not your typical, self proclaimed, average Christian. You have just answered one of those questions. Thank you greatly. 🥹👍

Thx buddy! if I ever run into you, the beers are on me!😂😂👍👍

I have an 02 Tahoe that I want to put a Texas speed stage 2 cam in. What else should I upgrade or can I leave it all original?

Thanks for the video just what I was looking for

That's funny. I was thinking of loading my breaker bar so I could leave some tension on it, hoping it would help. I didn't know if it would. Thank you

Bro. need your help...will this work on a 1997- s10 blazer...please reply.

Ya u can do that 2 get the truck 2 start an check out different circuit but that won't unlock the steering

How much should I pay to have a mechanic fix my frozen engine? Thanks

Being American left hand drive I would have thought cylinder number 1 would be on the left hand side ?

I'm about to do a front-end kit, and you just probably saved me half a day

I got a question. I got my Cummins ripped out again to do a full rebuild with some upgrades. The steering tie rod bar was rubbing the oil pan. Have you run into this before? If so what did you do to fix it. I was thinking of spacing the conversion brackets with some washers up a bit for clearance but don’t know about it because I feel like it could cause some more vibration with the brackets not sitting firmly to the frame. It’s probably the only way though but I wanted to know what you may have done for it.

Will I need to have a dry engine in order to pour diesel and sea foam?

I wanna do the same on my truck, witch leaf springs did you left out?

Ya gotta love straight shooters! No nonsense and short video. Thanks

how would i cummins swap my 2017 sierra?

You already broke it loose earlier. 😂

Worked perfectly 6 hits. Thanks

Worked well with my v twin evolution , had it sitting for over 2 years and got my bike on the road, thanks for the video really appreciate it, probably saved me a lot of time and money, cause I was about to pull the motor and rebuild it. Pls like and subscribe cause this truly works well especially on motors that hasn’t been sitting for to long! I can vouch for that

I love videos like this

How do I know which way to put my distributor in after I’m lined up with my time and marks

To reach the mark on the nut during installation you can hold the yoke with a large pipe wrench or put two bolts in the yoke and lay a long pry tool across it. Then just use a breaker bar to tighten so you can creep up on the mark and not go past. I'm sure your method worked well, just giving out more options. Thanks.

What did you use for a transmission

gutted fss and its a brand new pump with brand new injectors have new everything including lift pump and its still bogging when i step on it its like it runs out of fuel but i know its got loads of fuel

Somebody know how to start renault clio without key?

I guess a young buck can teach an old dog new tricks lol

So does this just disable the lock on the ignition

I'll try this. Thanks!

Fuck Off Joke Time People Are In Need Of Help

Does it leak

Would it work on my Infiniti g37 2010 ?

turning wrong way

So all the wire is 12 gauge except the one from the solenoid to the grid heater? What gauge would you use from the relay to the battery with the 50 amp fuse on it? All the relays I can find have the red wire on the side, not in the center. Is this an issue?

It works, it’s janky I used a c clamp with vice grips around the piston. The needle nose just didnt work for me.

19mm, not 17 on my ‘95

Excellent!!!!

I like your videos this one was much slower and easier to follow. Iam so ready to have all the stuff i need to finish my 4bt swap in my 82 toyota pickup.

A little different way . Install a simple portable 12 volt electric fuel pump to the inlet of the fuel pump filter housing . Crack all the fuel nozzle line nuts at one time . Turn electric pump on , as the lines start flowing fuel , tighten all nuts and start half throttle .

What year is this truck?

Thank you for the video. I was going to run and buy some tool to remove the drop spindle. I washed your video ran into the garage and in seconds the lower control arm dropped. Thank you for the video I just saved myself a run to the auto store and some cash.

I have a 78 Pontiac trans am 400, 73,000 miles. Plan on putting in a 489 lunati voodoo cam. It has the original 406. Will I be okay with only replacing the valve springs? Everything else is original.

How do I know which tank and pump to use?

One thing i learned....pull the fuel pump fuse while you crank

What if you had it on a slight slope and left it in gear, no break, chalks an inch from tires?

Easy Peazy, very well done.

Cool truck. Curious how much drop you have and how you achieved it. I love the stance. Is there a video on this truck being lowered?

now the question is, how do you turn the truck off? my ignition is stuck in the auxiliary position and i can start the truck but not kill it. does this work for turning it off?

Do you know what valves and pushrods i would get for a .560 valve lift cam in an all stock sbc 350?