Where do I put spring on button

can anyone expain why the flush button gets stuck down & you have to push it again to release it?

Thanks for your video. Am 78yrs and I followed your guide and fixed my over flowing toilet.

Are siamp flush valves interchangeable on the bases that stay in position when removed

Thank you very much

Hi how to open it please to wire inside

my recommended section has clearly lost its mind xD Why would this be recommended for me xD

This shyster company uses low quality plastic seal on the inlet top and also uses rubber seal for the main flush unit both should now be "Silicon Rubber" for a longer life.

This is the second one for the basement bat. kzbin.infoUgkxOuLt8IL_GxhhaK8DBuKEL-zV0UJVpWZn , works great

What is the solution?

About as helpful as a chocolate fireguard. Useless.

What a pointless video. How do you live with yourself?.

Awesome tip. This video saved me a very expensive visit from a plumber on a Sunday morning! 👍👍👍

Useless information. Basically, call them to rob you.

Bonjour a tous . ATTENTION !!!!!!!!!! ce système de chasse d 'eau a câble ne fonctionne pas et reste coincé tout le temps .Mon plombier n'a jamais pu le régler sur mes 2 chasses d'eau . Comment peut on vendre ca sérieux. Ne pas acheter ce produit ::::: arnaque

Replaced my cable but the mechanism at the flusher end keeps getting stuck up causing the button end to be stuck in, I keep having to reach in the cistern to push it down until it does it again!!! Anyone else had a fix for this

Without doubt the least helpful video on KZbin

Cable too short, awful connector and nearly impossible to connect

Try connecting with an actual toilet 🚽 🤣

At 10 seconds in, what does the little grey sliding door do? I can't find any reference to this

I've got this job to do tomorrow. Hopefully if all goes well, I'll be feeling very flushed.😃👍

The cable seizes up in the sleeving , leaving the flush continually running until you reach inside the cistern to lower the plunger.

Did mine today after finding my toilet had failed to fill and was hissing out abit of water only at 5am.... found the washer at screwfix for £3.70 and had it fitted in a few minutes after watching the vid. Only needed a flathead screwdriver to turn off the water.

Why do you show a different push button going into the cistern from the working mechanism?? I’m struggling going from the working mechanism to a fully functioning toilet because the clip doesn’t fit the gap. Any advice?

The flush button is a poor design, i have these fitted to two toilets and the base of the button cracked away from the sides on both within days of each other, lasted just over 3 years. Very very poor

What else fits a siamp flush valve does anybody know?

Wow it works it was a good tip⭐

rubbish quality, only lasted 3 years then had to be replaced

cheers, just what i need.

It won’t unscrew grrr

Quick and effective

We had 2 problems with our cistern. The diaphram in the inlet was split - fixed with a new one from ebay. Also the flush outlet failed to drop after the toilet was flushed. This was fixed by squirting WD40 down the flush button cable. Can only assume it needed a bit of lube!

Good I am plombar

Pain in the arse to replace as I have a built in toilet. !!

That's not very helpful! I want to know how to fix it and this tells me nothing!

I don't know how a company can sign off on such a poor quality design that never works. My toilet I inherited has this POS installed and it's caused me nothing but trouble. Please sack your product design manager and get rid of this not fit for purpose design

This repair will work 7 out of 10 times , then you need a complete new valve , there is nothing more you can do with it .

What if it’s a square button? I want to get into my toilet but there’s no lid whatsoever and only a square button and I don’t want to break anything.

Flushing valve slamming shut. Any ideas why?

Nice

Just in case anyone else ended up here looking how to remove the button and header tank lid on a Siamp this is how: Unlike the other two dual flush types which you will find many videos for you cant just pull the lid off and there is no hidden screw to look for. What you want to do is rotate the entire button via its outer ring. Using rubber gloves will give you a good grip on it. Keep turning it (anticlockwise) and slowly is will unscrew and come out of the top of the header tank lid. Once the button is free you can easily lift off the lid. To put things back, replace the lid and put back the button. There is nothing special to do for connecting the button apart from make sue it is aligned with the tube inside as you put it back. Tighten it up with some rubber gloves gripping the outer ring this time going clockwise and you are done

Just bought optima 50 today very Impressed until I noticed a continual trickle into bowl followed by a quick top up of water every 10 minutes. Any suggestions would be gratefully recieved

Where can I buy one?

Where should the water come through when it's filling? Does it come through the front of the valve or should it come through the spout on the side? Also, what is the other part on the top, (with the hole in the centre and some kind of rubber washer that can be seen) that can also be removed? Thanks.

I am totally amazed that companies stay in business with instructions like this. The little spring loaded button on the side of the box moves a plastic collar which slides out of the way of the threaded piece when inserted. Put your glasses on and look in the hole while you press the spring. When the end of the threaded stock is fitted into the plastic box the spring is released which holds the mechanism together. The plastic grasps the collar. There is a small collar on the threaded metal piece. It should be interesting tomorrow when I have to mount this thing with the plastic of the inside (under the lid) and the metal on the outside (top of the lid). Must remember that the mech plunger spins on the cables and the thread only tightens the plastic to the metal. Holy crap.

Thanks for the walkthrough!! And bro.... you gotta quit biting those nails lol. Good Lordy

Whats this parts name and where can I buy it?!

i've replaced mine and now the water comes oujt the hole in the arm and wont stop even when full. any ideas?

Thank you! I just fixed my toilet following this video.

doesn't show you how to work the internals of the white plastic box at the end of the cable that connects to the button. when I connected it, every time I press the button, the spring comes off inside?.