Listen very great reminder to to use heat specifically yellow can map has sold at autozone for 15$ and a torch tip ! Heat it up soak it in penetrative oil as your loosening very VERY IMPORTANT you tighten it back up or you'll be getting a tap a die and rethreading

Hello sir my car is also burning oil

she said ....hmmm wow

Really impressive. Ridiculously bad at aiming the tree unless that's what you were going for though. Lucky you are better at building sheds.

that shed is built like a brick sh1t house

That shed is idiot proof

Had alotta weight support stopping it first folks...wasn't a "dead blow"

That’s amazing

Put the pull strap higher to give more leverage and control

You did not show how you actually did the work step-by-step you just showed finish portion

Was that a shed commercial?

Grandpa put some extra nails in that shed when he built it!

Stronger than most houses

My poor 2000 4x4 4.7 has been a beast. Now at 192000 miles parts like this are going bad. I recently changed ac pump, alternator and battery. Funny part is with 185-192000 everything still has 11/99 mopar stickers on it 😎 i guess its been tough enough for me to invest in a few hoses. Thanks for the great video.

Thanks

Thanks Brother. Needed advice on compressing the piston. I suggest getting it started with the vice grips, then once it's spun around (clockwise) a few times, switch to a set of needle nose to finish the last two or three turns.

i have same trans. Mine is doing reverse failure at 145k miles.. MILES ON THIS TRANS ?

Or cut it from the back so blade will last longer..

how is it holding up?? im about to do my house

You didn’t even show how you took the inlet tube off the old water pump which is the one thing I needed… 😒

You only have t remove a T10 Torx screw between the turn signal lenses and the headlight lenses. The just pull the yellow lens unit forward. No need to remove bolts and the headlights.

You literly did not show anything worth while. You said there is the starter I tok it off and put the new one on.

what if ALL bulbs are good and working, but left turn still flashes fast?

Just a suggestion but try using a hook blade might make it a little easier👍

You didn't show how you took off the hose😢

Still popping up p0601 code after doing all this

Sho me toyota corolla 4A 16valve video

Excelent

Thank you 😊

Perfect

DO NOT use vise grips because you are taking a chance of cracking the edges on the piston, use one of the old pads, lay across the piston and use a C- clamp to SLOWLY push the piston back... And for goodness sake use a wire brush or something to clean the old clips if they are being reused, and brake grease would also help.... btw they're Pads not Shoes...

What do I do if I can't turn it

Doing this on my sons car tomorrow but i will definitely be putting it on axle stands not just on a jack

Why do it the hard way?

Impact wrench to break them loose

I have both tail lights working but driver side brake light and turn signal isn’t working.. checked the bulb and fuses and everything seems fine.. any idea what could be my issue?

That’s why mine didn’t work, I didn’t have a cat to supervise it. 🤭

I have hazards to

I have no brake lights I have turn signal but no brake lights I have running lights but no brake light install new brake light switch

I'm trying to replace my o2 sensor in bank 1 sensosr 2 and everything im finding shows that it should be in the catalytic converter but my kia does not have anything in the catalytic converter, not that it was sheered off or missing there is not even a spot for it. Every video I find says thats where it should be, going crazy! Came here to see if you had a video on that but unfortunatley I do not see one. The search continues.

How long has it been since you done plugs? Probably needs a set of plugs. Whenever a coil goes bad and you drive it you fuel foul the plug.. And really should replace it and the coil at the same time..

Was able to diagnose and repair same exact problem--brake lights/hazards/signal, and I could hear the relay sound when I depressed the hazards (but not flashers). You need Novita LM474 Relay right under steering wheel. Drove me nuts for about 6 months. kzbin.info/www/bejne/iXbMmqSjbLuGrpI

Your old tube was broke that wolverine has a groove that goes around the tube just like the replacement one so part of your tube was broke off in your old water pump it actually snaps in with the oil ring

Lucky for me that's the exact mower I'm having trouble starting. I'm about to start with the plug and inspect the fuel in the tank with flashlight. Will report back shortly!

Was your connector a 2 or 3 prong I have a KIA Rio LX 2013 and cannot find a fan assembly for it with a 2 prong connector

Thank you for great video. By following your directions, I was able to fix mine.

Thanks for the kia Rio 2013 brake video you made it look simple😊

Talking about what to do and actually showing what to do step by step is two different things. This was a very flimsy made video. I will have to go find a couple of other videos just to see what the hell for sure to do.

This is so cool! I'd love to be able to build my own shed!

I don’t have the backseat release switch in my trunk please help me