Try check out rep fitness for home gym equipment and rogue fitness has plenty of options on their website
@rogerbuchanan96002 ай бұрын
very clear description of how to install and how it works!
@dirtmcguirt61185 ай бұрын
Question, why do you need the negative bus bar? Can’t just wire the negative straight to the switch panel?
@eastsidewrenching5 ай бұрын
You don't need the negative bus, a wire to the battery negative terminal also works. The negative bus is a choice I made for organization
@DaRealGust06 ай бұрын
Why did you add an In-Line Fuse to the bow light when there was already a 1 AMP fuse in place?
@DaRealGust06 ай бұрын
@@eastsidewrenching ahh gotcha, thanks for the reply 👍
@derekl.506910 ай бұрын
Thank you for being straight forward and to the point, a lot of you tube reviews are so drawn out and ridiculous
@BeTactical11 ай бұрын
So helpful, exactly what I needed!
@gerardoc102811 ай бұрын
Do you have to drill to install the pull up bar?
@eastsidewrenching11 ай бұрын
No, sorry I didn't show that part, the holes come pre-drilled
@gerardoc1028 Жыл бұрын
Dimesions of the pull up bar.... looks very small👍✅️
@eastsidewrenching Жыл бұрын
Agreed, it is just under 28 inches wide
@gibbygordo Жыл бұрын
How has the machine held up? Is it still a good choice for home gym? Has your opinion changed on anything?
@eastsidewrenching Жыл бұрын
It is still a good choice, no issues so far. I recently took the weights off and I am planning to rotate the machine away from the wall. If your floor isn't level I would definitely say that it's worth making shims for the feet out of wood and then adding the weights after.
@rico2207 Жыл бұрын
It's OK they don't draw hardly any amp micro amps
@KG-xf9ew Жыл бұрын
Thanks for the video. From 6:00 onward that light is basically useless. Same issue with all of them.
@_Truth_777 Жыл бұрын
I wouldn't say useless, it'll still reflect off of hazards in the water
@KG-xf9ew Жыл бұрын
@@_Truth_777 Yes I admit you are right. It's better than no light and you can at least move forward. But it doesn't illuminate enough to cruise at any speed. But then again none of them that I've seen really do.
@OliverStonesUK Жыл бұрын
I'm 6'5" or 197cm tall. Do you think I'll be too tall for this machine? What is the height from floor to the bar at the top? Great video btw, thank you for sharing this.
@eastsidewrenching Жыл бұрын
Thanks, the floor to the top of the crossbar is 6' 8". The floor to the bottom of the crossbar is 6' 4"
@transitiontrading Жыл бұрын
I anchored mine to the ceiling - One angle iron at each end - solid as a rock now
@johnroberthanna1623 Жыл бұрын
They make the best LED lighting..!!
@lindy335 Жыл бұрын
Interesting series of videos. I picked up a few details I missed by watching both episodes. I'm in the process of installing the 4 gang version of this panel in a 15' Boston Whaler. The boat has no protection from the weather and salt spray. I have a couple of questions and a remark. Can you share the relay particulars? What is the make and model number of the relay you are using? Where did you shop for it? Does it come with the base? And finally, is the relay designed for marine use? I just have one remark, I'm pretty sure I understand your concept (thank you for sharing this, it's helpful) but it would have been good to have a simple hand drawn wiring diagram, maybe just a photo of it. Thanks again for posting the videos.
@artiekellerdrums4440 Жыл бұрын
Never use a different gauge wire for your ground. Always use the same gauge for both legs.
@robincampbell4945 Жыл бұрын
*Promosm* 😊
@BodySolidFit Жыл бұрын
Thanks so much for this video. Very helpful! Appreciate you choosing Body-Solid!
@ty1977 Жыл бұрын
I got my 8 switch installed and doesn’t light up . Do some not light up? Thanks
@eastsidewrenching Жыл бұрын
"Switch Only" panels do not appear to have LEDs
@ty1977 Жыл бұрын
@@eastsidewrenching thank you
@brianboylston4014 Жыл бұрын
Regarding the status LEDs always being lit: you can control this using the "dimmer control wire" (see the instructions). I'd have to check my setup to confirm, but I think I disconnected the dimmer control wire from the bus bar and connected it to a panel switch output so that that switch now controls the status LEDs. In my case, that same panel switch also powers my cabin lights (which each have individual switches in their fixtures).
@frankhunt5018 Жыл бұрын
Good job on the install.
@Patcher4011 Жыл бұрын
New to wiring. To confirm, the rest of the switches still operate without that ground because the accessories have their own independent ground?
@buckreynolds1779 Жыл бұрын
I share same concern about led on all the time.
@CaptBull Жыл бұрын
Nice video that demonstrates the guts and the outside of the switches. As far as at the end of your video when you talk about a big bulky switch, most votes that are running multiple accessories such as pumps, vhf, radar, different lights, etc will already have two batteries on the boat with a battery switch. Blue seas makes an awesome add a battery system and before I leave my boat I turn the switch off which shuts off power completely to the entire boat so there's no worry of ever having any LEDs draining. Sorry for being kind of long-winded but the short answer would be if you have that many accessories on switches you should have a battery shut off switch already.
@barrafishing11562 жыл бұрын
Why you change the fuse
@RhettyorNot2 жыл бұрын
How often do fuses go in these? I'm having trouble with two of my switches
@eastsidewrenching2 жыл бұрын
If the fuses are sized appropriately, not often at all. I haven't blown any yet and I am running way smaller fuses than 15A
@coleah692 жыл бұрын
Cool little video. Electrically incorrect tho. You have 2 fuses on one light. 😉
@necokgezdik35362 жыл бұрын
perfect
@metamorphai2 жыл бұрын
Thank you for posting this video. I want to use these panels in a portable solar powered battery bank. Every watt matters in this setup, so I don't want those LED drawing current at any time.
@fishingfool26442 жыл бұрын
Just install a blue sea switch to power the panel.