3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@Okkalaboy 6 күн бұрын
Sir please how to configure l2 switch
@shunmugaganesh8697 16 күн бұрын
Very useful information
@prathapk7665 Ай бұрын
Only one correction, images shown in the end of the video is not Valve Plug, it's called Valve Cage. Difference is Valve Cage will not travel as it will be fixed inside the Valve body and the plug will be connected to the stem which will be traveling inside the cage.
@sreenivasvengali8612 Ай бұрын
Great information,,thanks
@jibinjoy8213 Ай бұрын
Only trips are mentioned in cause and effect?
@GateSpartan 2 ай бұрын
Good info
@engchoontan8483 4 ай бұрын
we asians simply put the control-freaks with the madmen and karens for world-domination defence. same for missiles
@engchoontan8483 4 ай бұрын
hokkien use roof-designs to catch electricity, wall designs to kick-trigger-kick switch and floor-designs for height crossings and door placements and guards = same thing and heat, air, moisture, ionisation-baking-air till conductor-inductor-... switch room is placement paired with device(elevator, escalator, ... pump-room) manual that need-no.need = (placement)(position)(height)(...) structure itself
@adilmuqeem7377 4 ай бұрын
Wow.. this video is very informative to me . Sir can you please Make a vedio On speed control of temperature Controller I want to control temperature speed ..i want 1.5°c per minute ... But my controller can not do this ..
@bastiangonzalez6761 4 ай бұрын
Wow! I was looking for many videos to understand this concept and Finally, I could understand it. God bless you and best regards from Chile!
@mgrtrq 4 ай бұрын
Hindi explained
@mahamatabakar8939 5 ай бұрын
Good explaination do not give up.Thank you
@khalifajaber4070 5 ай бұрын
Thanks for your clear explanation and video
@hussamabs 5 ай бұрын
I believe you mean the cage not the plug
@grounded9623 5 ай бұрын
There is no instantaneous processsing, real time means that it takes time. You only communicate when you have the token.
@DIYHIC 6 ай бұрын
Great presentation
@muscatmama 6 ай бұрын
Fantastic explanation 🎉
@sureshnair3848 6 ай бұрын
Hello, can I get your contact number..
@AdityaKumar-be1ev 6 ай бұрын
The flow rate directly influences the amount of energy required to compress a gas. By calculating the flow rate, engineers can determine the energy consumption of the compressor, which is essential for evaluating its efficiency. The efficiency of a compressor is typically measured by the ratio of the useful work performed to the total energy input.
@muscatmama 6 ай бұрын
Excellent explanation 🎉
@ahmadamirudin3666 6 ай бұрын
What is PDTC?
@damithgayashan9873 7 ай бұрын
Super
@vishnuvinu4720 7 ай бұрын
Good
@palanisamy7137 7 ай бұрын
Thank you sir
@palanisamy7137 7 ай бұрын
Nice Sir.I have one doubt.it might be chilli question.correct me if I wrong Why do we required here 230V AC Supply feeder.we are already converting the 24V DC supply in Power distribution panel and those supply we can use for IO cards and controllers right ?.If not then why we are converting to 24 VDC in PDP panel.where we are going to use?Please clarify
@palanisamy7137 7 ай бұрын
Thank you sir
@Harpreetsingh-lz9lv 7 ай бұрын
Any software to measure...?
@tal5338 8 ай бұрын
Excellent...can you add back Standards and P&ID/SIL so it can be a good references. Thanks 👍👍👍👍👍👍
@SaipriyaDyavarashetty 8 ай бұрын
what happens if we place dryer first and receiver last ?. means from receiver discharge its going to consumers, what will happen in this case?
@karkun1466 8 ай бұрын
Good explanation
@__ROHANM 8 ай бұрын
Thank you. And I have one more doubt ,From this which one is highly efficient?
@venkatraman5995 9 ай бұрын
Sir,please explain about timers,how it used in instrumentation process,update more about instrumentation sir. And explain about logic diagram.
@AVoyagerCouple 9 ай бұрын
How to change the scale high SH in a faceplate?
@INSTRUMENTION1234 9 ай бұрын
Cryogenic control valve working and material yo be work video please upload sir .
@venkatraman5995 10 ай бұрын
Logic diagram also explain sir..
@venkatraman5995 10 ай бұрын
Thank you,expain in pannel side live,it will be more usefull..
@arwaelkasaby471 10 ай бұрын
Thank you for the great explanation. I have a question, please. What will happen in the condition of startup? which is normally will be lower than the Low Low alarm.
@learninstrumentationengine268 10 ай бұрын
We have a philosophy of startup overrides. Otherwise, Class B overrides will be implemented. It is explained in our channel. Pl check
@arwaelkasaby471 10 ай бұрын
thanks
@mohsinraza9944 10 ай бұрын
Good video
@athul3459 11 ай бұрын
One of best tutorial Sir really impressive I subscribe your channel
@pankajpatil7714 11 ай бұрын
Very Good Content 👍
@pankajpatil7714 11 ай бұрын
Very Good 👍
@bhargavadukanam 11 ай бұрын
Excellent video, very informative sir. Keep going 🎉🎉
@intellectualoasis Жыл бұрын
Please what does DL and VL stand for?
@akankshasharma9000 Жыл бұрын
why 60 farenheight is considered only ?
@whoismewhosisyou 4 ай бұрын
standardiezed value
@kenchicken1360 Жыл бұрын
Do you have a module on how to creat a out of range alarm
@abdessamedghettas7167 Жыл бұрын
thank you
@abdessamedghettas7167 Жыл бұрын
Thanks
@saikrishna3977 Жыл бұрын
Best video sir
@محمدالتجاني-ل4ر Жыл бұрын
Good explanation sir, good English accent just keep on. God bless you .
@yashwanthns2874 Жыл бұрын
The last position of this video need improvement, which it is not plug which is shown in this video
@prathapk7665 Ай бұрын
Yeah, It's Cage