Пікірлер
@MoaByte-v2z 21 күн бұрын
I love the pedal remedy. I put the Holly Sniper on mine and was able to rig the stock rod linkage with heim joints. I can feel the engine move on the motor mounts through my right foot. 😅
@sjwalker5696 24 күн бұрын
Speed meter needle bouncing tighten the cables up.
@danieldufur7474 26 күн бұрын
Hey Mize, would love to see the routing you have for the DESMOG. I currently have capped every one of the ports on the carb, I have no HAC HIC, Vac advance, or anything hooked up at all. The rig runs decent once warm, but im thinking theres probably a few things on the carb I should hook up eventually. Can i drive the rig long distances with everything just capped off for now? the idle solenoid is hooked up but nothing else. every single thing is capped. Dan
@landcrusher909 26 күн бұрын
Just watched. Thanks for the help. I just picked up a 1972 FJ55
@Peenits69 Ай бұрын
Man I wish you showed your work
@kirkyboy5426 Ай бұрын
Slap a cummins engine on it👌
@fricknjeep Ай бұрын
hi there , well done , there is a 53 sitting in my barn , been there around 25 years now , best to all john
@somalia5019 Ай бұрын
New subscribed from Somalia
@chrismcfarland738 Ай бұрын
These segments have been so helpful as I am completely tearing down and restoring an 85’. I’m almost done and it looks amazing. Thanks for your help!
@abcstudiostanzania Ай бұрын
Nice ❤
@abcstudiostanzania Ай бұрын
Nice
@79series Ай бұрын
I put a 3f into a fj40 that had a 2f, was a PITA, the motor mounts on the 3f had lots of extra alternator bracket, a/c and power steer, etc. Had to make new mounts for the 3f.
@JC-pu1ej Ай бұрын
A top-notch mechanic! Great video!
@JC-pu1ej Ай бұрын
A great video for a five dollar truck!
@jonbrooks4843 2 ай бұрын
Thanks for these videos. The details are wonderful; “end screws are different and look like this “ and these insights help hobby mechanics like me working on my 85 FJ60 “Wilson.”
@ryaninslee3127 2 ай бұрын
How did you handle the radiator. I was told that you have to clearance for that somehow?
@petrusmngwevu8316 2 ай бұрын
Where in South Africa can I restore my FJ 62 Landcruiser to this level?😢
@jonbrooks4843 2 ай бұрын
Great video. There are 4 bolt holes to secure cover to engine, maybe 2 fl that connect ton air box, and a couple that are a couple of open holes in the valve cover nothing attaching to them, why is this?
@mikem4346 2 ай бұрын
Please Please a video to show how you will merge the FJ55 wiring herness to FJ62 Wiring Herness.
@mikem4346 2 ай бұрын
Nice work, could you make another video to show how you will merge the FJ55 wiring herness to FJ62 Wiring Herness.
@mizeadventure9438 2 ай бұрын
It will be in part 2
@cfrost 2 ай бұрын
Nice work!
@deepbludude4697 2 ай бұрын
Thats an achievement man well done!
@mizeadventure9438 2 ай бұрын
so stoked to have it in the truck. just opens new doors for this rig .
@deepbludude4697 2 ай бұрын
Im digging it!
@mizeadventure9438 2 ай бұрын
agreed! its so bad its great!
@TheDustyBearCruiser 2 ай бұрын
I love it! Those Iron pigs are awesome, but i did get a kick out of calling the 3fe "modern."😂 You wouldn't happen to have a fj80 service manual I could buy?
@mizeadventure9438 2 ай бұрын
I mean it's modern to me ha. still a total upgrade. I don't have anything for fj80s. don't really mess to much with them .
@TheDustyBearCruiser 2 ай бұрын
@@mizeadventure9438 True, you mess with the great great grandpas and that takes some balls 😂
@michelle-lz8tg 2 ай бұрын
these are awesome jeeps....and they are getting more and more desirable along with their flat fender cousins (willys mb, cj2a cj3a, cj3b)...hang on to it if you can
@josehernandez-ni9it 2 ай бұрын
to remove the entire engine harness from a 2f in a 85 lc does the entire da sh have to be removed?
@mizeadventure9438 2 ай бұрын
Yes
@ToranaA9X308 2 ай бұрын
FFS stop calling it a TRUCK. It’s just a LANDCRUISER just call it that.
@urbanitesgarage3299 Ай бұрын
its a truck
@ToranaA9X308 Ай бұрын
Call that a TRUCK in Australia and you’ll be laughed back to the airport you arrived from. It’s a 4 WHEEL DRIVE. Trucks are for hauling goods and towing a TRAILER
@urbanitesgarage3299 Ай бұрын
@@ToranaA9X308 well where this particular cruiser is at is in America , and the land of the free would consider that a truck "mate"
@JabborNajibi 3 ай бұрын
❤❤❤❤❤🎉🎉🎉🎉
@Gungaganoonga 3 ай бұрын
Need some soap
@vintagespeedandperformance6615 3 ай бұрын
Thanks for sharing the build. Question for you, where did you end up setting the base timing? I have a 1F in my 40 that when purchased came with an Offenhauser 4BBL intake, edelbrock carb, header and flow master installed. It idled good and sounded ok crushing but would make your eyes water it was so rich and completely gutless. I found the timing was way off from spec, like several degrees ATDC. I set it to spec, 7 BTDC and it helped enough I could start tuning the carb. Ended up at 12 BTDC and it’s good. Good power and runs smooth. Had to disable the secondary on the carb though. Just bought a Holley 2bbl to try out. I tuned a friend’s 2F that has a Rochester 2Jet on it. Ran ok but was a little rough at idle and had a flat spot. Ended up setting it to 14 BTDC and it purrs at idle and going down the road. Flat spots eliminated. If you’re still at 7BTDC, you can squeeze out some more performance with a timing change.
@danieldufur7474 3 ай бұрын
Lovin it Jonas! Had a few questions for you. When I drained my fuel tank the other week, I noticed dirt in the bottom of the clean drain pan from the gas. It wasn't atone but about a quarter of the pan had dirt/grime in it.. How big of a deal is this? Will the fuel filter catch dirt accumulation like this? Truck sat for a while. Probably at lease 3-5 years at one point. Cracked Rocker support. When I was installing the rocker assembly with a fellow cruiserhead one of my rocker supports got a crack in it. It toruqed down just fine, but wondierng if you've ran into this before. Thanks, Dan
@mizeadventure9438 3 ай бұрын
With that’s much stuff (most likely rust) coming out the tank I would be pulling it to clean it out the best I can. You will have problems down the line with your fuel lines or carb clogging from that. You could pull the rear carpet up and open the fuel sending unit on the top of the tank to take a look inside of it to see how much stuff is really in there. There is also a open recall with Toyota for a new tank. But would need to call them for that. Possible your truck already had it done. Rocker support wise. I’ve seen stuff like that before and honestly I would be replacing anything that would of cracked. As if it breaks off inside the engine bit of metal could do some major damage to your engine and bearings.
@danieldufur7474 3 ай бұрын
@@mizeadventure9438 Thanks Jonas, appreciate it. It's the new tank, truck sat for a while. Dan
@ian0841 3 ай бұрын
Great job as always!
@mizeadventure9438 3 ай бұрын
Thanks for watching! Stay tuned for some new content coming soon.
@Toca9990 3 ай бұрын
Love you videos... I always learn a thing or two about this old rigs
@mizeadventure9438 3 ай бұрын
I’m so happy about that! That’s the point of these videos. I want guys to have a resource with visuals to help you work on your own stuff! stay tuned have a lot more content coming
@MoaByte-v2z 3 ай бұрын
This made me happy. You may need to swap in a master cylinder from an 80 series inorder to get the most out of the brakes. Fj Cruiser steelies will fit but you will need 1.25" spacers for the rear. I like that EFI better than the Sniper, it looks like a GM throttle body.
@mizeadventure9438 3 ай бұрын
I thought about a different master already. The Toyota one is working fine for right now. May upgrade as the project develops. I got a good cool set of rims for the truck for PT2. It is the GM set up. I’ve worked with both the Holley and gm injection systems. I like the gm one also. I would also think parts down the road would be easier to source. Thanks for watching and stay tuned for future episodes.
@tomaszsleziak3940 3 ай бұрын
This's sniper efi kit?
@mizeadventure9438 3 ай бұрын
It is not.
@AyzenSama2014 3 ай бұрын
So cool
@darkbird1651 3 ай бұрын
Awesome work Joans!
@mizeadventure9438 3 ай бұрын
Thanks! can't wait to have this truck finished
@DuanDao 3 ай бұрын
Exciting man
@mizeadventure9438 3 ай бұрын
Agreed! SIKED to save another one of these trucks
@MoFoTUS 3 ай бұрын
Don't leave me hanging on this. I NEED to see it finished. Great job to this point.
@mizeadventure9438 3 ай бұрын
Working on it! Promise!
@chriskreple 3 ай бұрын
Nice!
@خالدالشهري-ن3ز 3 ай бұрын
استمر اخوك من السعوديه
@randywarren6925 3 ай бұрын
Question, what did you use to connect the SBC to the Toyota transmission?
@chriskreple 3 ай бұрын
Great episode!
@chrissteinhilber8839 3 ай бұрын
Another heart ❤️ transplant…Wishing you great success!!!!
@FluffsTravel 3 ай бұрын
I love that you used a small block 5.7 they are great engines. I know everyone uses the LS now days but I’m old school great work man!
@leonelplascencia2990 4 ай бұрын
Really good content🎉
@copelandconservationmissio126 4 ай бұрын
What size lift and tires on that rig?
@keegancooke8271 4 ай бұрын
What did you do to it that makes it sound like that is it the cam
@abelhellman2741 4 ай бұрын
Can you make a video of taking off the door on a fj60
@preunit13 4 ай бұрын
Great video, but if I were the customer watching this, I'd wonder why there wasn't a soft towel or something under the grill when laying face down on a rusty tailgate while working on it.