Thanks for the comment. "Snipe" simply refers to a non-uniform cut where the blade meets the wood. Yes, the location of the snipe occurs on the top side of the wood. However, as shown in my video, my planer had significant flex in the table, which exacerbates the snipe (changes the distance between the blade and the wood). The new, rigid table that I made eliminated that error. Obviously, it doesn't eliminate any snipe that may occur due to flex of the cutterhead assembly (above the wood), but it did significantly reduced the snipe cause by movement of the flimsy table (below the wood).

Glad it was helpful! Thanks for the comment.

@@canuckjim1941 Thanks. Glad you found it useful.

Glad you enjoyed it

Thank you. Much appreciated!

@@marky0140 Mishaps on any power tool can be scary! Thanks for the comment.

They are great machines. They don’t make many tools these days with that machining and quality.

Thanks. I highly suggest buying a copy of the book “How to Master the Radial Arm Saw” by Wally Kunkel. He includes much info about molding and shaping with the RAS. You can find old Delta/Rockwell molding heads and profiles that work very well.

Thanks for the comment. The second season I painted the top sides for better sun protection, but leave the under sides varnished for appearance.

Thank you. Hope you find them useful.

LOL! Well, glad you eventually watched and appreciated the full content. I appreciate the comment and hope it was useful. Thanks!

Glad it was helpful!

Great job again !!!

Thanks!

Thanks. It’s 12x48 inches.

Thank you! Glad you found some of my videos useful. Hope your edge-jointing works well.

Thanks. I’ve never had the jig saw attachment, but it seemed more of a novelty rather than a useful accessory. However, I have found the sanding disc attachment to be very useful.

Thanks. Once winter comes and I begin taking wood to burn, I just take pieces from the top and keep the rest covered with a tarp.

@@brianweekley5700 thanks! I’m going for it!😊

Thank you. Yes, a great application for the RAS!

Thanks for the comment. You did see this was a workshop? Yes, very beefy for a small shed, but not 8x8s (I think 6x6s)? However, the purpose of this design was to give each student the opportunity to cut each piece and joinery needed (e.g., a post, a rafter, a joist, a brace, a rafter seat in the plate, a tenon on a tie beam, etc…). It really was a great workshop and well done.

Thanks. I've never seen splines left proud, but give it a try!

Great question. The push board is really just pushing the last few inches past the blade. Not unlike using a push stick to push a board past the blade on a table saw. As long as the board is cut square on the end, the push board mates with it and pushes it straight through without problem (better than just a push stick). In addition, I often use “board buddies” when ripping (you can see them in some of the examples shown in this video). These one directional wheels are angled and also serve to pull the board towards the fence.

Thank you. I forgot about the board buddies, but on other active RAS demonstrators I’ve watched, they use a similar push board like yours, or occasionally, a push board from the back, then a push stick on the side, and that also prompted me to wonder why a push board didn’t have an “extension” stub on the outer length rear portion of the rear of a workpiece. It just seemed to me, having that lateral pressure pushing the workpiece towards the fence was something one always tried to ensure.🤔 The one downside to my corner tab concept could be the limits of whatever pushboard width one built, in relation to the workpiece, so then a complication then is whatever arm that presses against the board length, would need to not interfere with the cut path and blade guard. I’m curious to experiment with this idea, even if it turns out not to work in real life. It’s just a thought I have after watching several ripping cuts on the RAS.🤔🤷🏼‍♂️

I will strongly consider making or buying a board buddy of some type anyway, they seem a smart accessory to use routinely.👍🏻

@@leohorishny9561 They do come in handy.

@@leohorishny9561 If you invent something better, please share.

LOL! I’m old, but not that old.

Don’t get me wrong, I like to use a table saw too. Just intended to show the RAS works just as well to rip.

Thank you. I appreciate your comment and support for my content. Glad you found the video useful.

Glad you like it!

I’m sorry, I really don’t understand what you are asking. Are you talking about how the box is made that sits behind the saw? If you join the “DeWalt Radial Arm Saw Forum”, you can find a drawing of a similar design here: forums.delphiforums.com/woodbutcher/messages?msg=601.1

It depends. Dust collection on a RAS is notoriously difficult in many configurations. However, I find it does a pretty good job when ripping. I have a separate video about dust control on a RAS that you might find useful: kzbin.info/www/bejne/mJu2kmuPip6Ybrssi=H2H5wa_D4Km74ug2

Thanks for the comment. Yes, the accessories are still easily available. I just looked and saw five shaper guards for sale on eBay (although some unreasonably priced). Corob Cutters still manufactures new molding heads and knives, but used Delta/Rockwell ones can easily be found on eBay too. Really not a problem. Also, if you’re not a member already, join the “DeWalt Radial Arm Saw Forum”. We have members who frequently have accessories for sale if you ask.

@@brianweekley5700 I saw guards for Craftsman, not for DeWalt...I mean, I assume the cutters and heads wouldn't matter as long as they fit a 5/8ths arbor, but would the guards themselves fit?

www.ebay.com/itm/196572647960?_nkw=dewalt+shaper+guard&itmmeta=01J5VV723TRVST01S2HVQHSH0R&hash=item2dc4a49218:g:w-QAAOSwxvlmxUWn&itmprp=enc%3AAQAJAAAA0HoV3kP08IDx%2BKZ9MfhVJKl%2B9N6pCqiJKtSzOXcwutHCAgPmVowneiau7k5J6MxdbZkVWeNQQ9WyCxhH60MDBKIWP1MDoe4BkmnhB8wchsgkdFHt5rVZJQWj1XOH0cQaHzaNilqdfQHGOLdy2CQOiVU4YCRJ0vdE94E9tVzBKEWa2xR4VJbqYBwnX0mkKKp9%2BQriwqhclO3IQfSIbI1SwFcVjUjKkXRfC4s1v9CnghOGTt3ngCdADl%2FjMn2E50%2FspCqPAJymWnbFR7HtMYpy1uI%3D%7Ctkp%3ABk9SR_yhnPuuZA

If you have a DeWalt, you need the DeWalt shaper guard. You are correct-any 5/8” arbor molding head will fit any 5/8” arbor saw. However, the Delta/Rockwell head is better than a Craftsman (greater mass).

Thanks. Much appreciated!

I couldn’t tell you how much this project cost-didn’t keep track. The router lift is defined the most expensive and important part of this project. However, probably less and better quality than most decent router tables out there. I enjoy making things, so tools are an investment to me.

Thanks. Unlike a table saw, a RAS doesn’t need a riving knife (for the purpose of preventing the wood from twisting behind the blade and kicking back like it could on a table saw). However, a splitter (for the purpose of keeping reaction wood from closing up and pinching the blade) would be desirable. Although some RAS models may include a splitter, many models do not. Maybe because the kickback pawl is so far behind the blade (on my DeWalts). Personally, I’ve only experienced pinching a handful of times (tends to stall the motor). In that case, stopping the motor, retrieving the board, and feeding through again usually relieves the internal stress and stops the blade pinching.

@@brianweekley5700 Thanks much for the response. I think I meant splitter, just to keep the wood from pinching.

Thank you. Yes, I draw almost everything I make in Sketchup first. It helps me eliminate mistakes and make sure everything works as planned. We are cyclists too (recently returned from riding RAGBRAI)!

Thanks! The RAS is one of my favorite and most used tools in my shop. The Workmates are also very useful.

Thanks. The MBC is a fine machine, albeit under-powered. However, works fine for 1x material with a good blade and taking your time as you noted. It also makes an excellent moulding/shaper!

@@brianweekley5700 I have a very old molding head from Craftsman. Being an ex-tool grinder, I can keep things razor sharp. It did a pretty good job with my MBF that I used to have. I just got done making your Ripping Pusher. Much better than the one I was using. It's like a riot shield.😆

Great to hear! Have fun with your new saw.

Thank you!

@@brianweekley5700 I subbed to your channel... lots of good content for me. Former rancher, now restoring a craftsman home (1939).

Thanks. Sounds like a fantastic project!

@@martingogela3324 Thanks!

Check out my video on making extension tables. It shows how they are connected to the RAS table. kzbin.info/www/bejne/eqDEZHWkqthoqJosi=0TkbxbG4UEajxXHb

Thank you!

Thanks!

Sorry, no.

LOl!

Glad you enjoyed it

Glad to hear you’re getting another. Sometimes, the 10 inch saw comes in handy. Enjoy your new saw.

@@rraffaell73 It comes in useful at times.

@@jerbus7956 Thanks. The fence is just 1x pine (3/4”).

@@Kathyskollectables Try double-sided Gorilla tape. You might have to cut it, but that stuff is amazing!

Thank you very much!

Glad you like it!

Thanks! Much appreciated. That saw was my DeWalt “Builders 10”. Unlike most DeWalt radial arm saws, this one has an under table elevation crank. I gave this saw to a friend and substituted it for a better, cast iron model (1030).

@@brianweekley5700 Very cool! Yesterday I watched part 2 of this video, and I can say that my enthusiasm for this type of machine is only increasing. I recently bought an 8101, and it hasn't arrived at the shop yet... Did I make a good purchase?! It seems to be in good condition... Thank you for the videos you've been making, they're like reading excerpts from books and manuals on the subject. See you soon!

Thanks. Sorry, I’m not familiar with the 8101. I believe that is a European model-possibly made in Italy? They are different than the American built DeWalts, but should serve you well.

@@brianweekley5700 Yes, it is one of the models made in Italy by DeWalt... I'm not sure, but it was made in the late 80s or early 90s... I've just entered the RAS universe, even though I've liked them for a long time... Who knows, maybe in the future I'll be lucky enough to get a rarity from the 60s. Let's see!

@@rraffaell73 Consider joining the “DeWalt Radial Arm Saw Forum”. Lots of good information there and a great place to ask questions or learn about all things RAS related.

Sounds great. Whatever works!