my 2004 MD got the same issues..

Where do you order your parts from

@EZAS music Tools the knob are all the same type? I mean, if I solder an Hi Pot on Gain Pot, is the same? thank you

Is there a difference between this and the 6b PRO ?

Question: I need to replace my balance poti on my DJM 500. Can I use the DCS1034, DCS1054 potis for that? These are the ones for trim, headphones, monitor

Question: I need to replace my balance poti on my DJM 500. Can I use the DCS1034, DCS1054 potis for that? These are the ones for trim, headphones, monitor

What happen with the rust? I have the same problem and I want to know how solve it 🫤

my man even strips down and refurbishes the original encoders. didn't expect that. much respect for this video - well done in every regard.

Great! Thank you!

desculpa mas por que uso o de 1000 35v no lugar de 6.3v sou leigo mais tenho um aparelho com o mesmo defeito?

Do u do repairs ? I have a g major 2 thats acting up intermittently and im not electronics savy ..from what ive researched ,it was eaither a capacitor, the ribbon cable or chips not being properly seated...ive reached out to TC but they barely replied and didnt sound like they would help ..please let me know

Hi, I want to change the screen lighting but leaving the original screen. I will only change the light, but I would like to remove the inverter that makes noise. I think you have replaced the screen but you have left the original one that works with the inverter but you have made a bridge and put a resistor I think of 10. What is not very clear to me is which pin you bridged and if by doing that then I could remove the inverter leaving the original screen. Thanks

Good work. I have one of these that almost got destroyed. How much do you charge to fully restore one of these that has been hit with a hammer and bent by the faders with a broken screen?

Great work! Please share info on the screen :)

Exel nte, muchas Gracias por compartir

Muchas gracias por compartir saludos desde Mty México

Man... I need to do this on ADAT input 1. Grr! It's gonna take a while to pull it out the rack though....

My Twister still works fine, i watched the video to learn about if a lower profile enclosure would be possible and it seems like that. I think they had the stage in mind when developing this thing and build it to be not to low beside mixers etc. but for the desk i always wished it would be closer to my regular keyboard.

3:32 is that typical of lcds, having to desolder the connecter right off the pin header? Isn't there usually a connector soldered to the lcd?

How long did this take you? Amazing work 🙏🏼

Bom dia gostaria de reformar djm 500

where can the replacment display be availed from ?......nice documentation, thx.

Шляпа

Have you run into a problem with it saying the serial number is invalid? No pads or buttons work. Worse, it’s intermittent.

Moist

can't change any selection after warm up still work

How do the Muses compare to the Burr Brown opamps shown in your other video? Which do you prefer?

Did you replace the faceplate? Or have you restored the old one? If yes, how did you do that? 😇

Thank you. My one made same issue.

I need a repair on my djm 500 whos the best person 4 the job???

unbelievable!! A little daunting for me, the newb😰. I suppose i am embarking on journey to learn electronics. My djm600 died today. I admit, Ive had it powered on for weeks, and maybe months straight. Never turned it off.. I had a loop of white noise playing all-day-everyday. I woke up and the thing was dead. When i hit power, i hear a slight buzz, but🤷‍♀. Much love🙏🏻🍻🍻

Can you do this for other mpc 500 users like me?

Tengo el mixer behringer djx 750 que el canal 2 esta muerto no funciona, que pudiera estar fallando? gracias de antemano.

Are you able to midi slave the XR10?

such an cool music , subbed!

Thank you very much for sharing this! The previous capacitor did not look damaged at all in my unit, so I tried either way as someone else mentioned the same thing about their unit. I replaced the original 6.3v with a 25v instead of a 35v shown on the video which also works.

Thank you very much for sharing this! Adding to the statistics, this repair worked on a G-Major unit. The previous capacitor did not look damaged at all, so I tried either way as someone else mentioned the same thing about their unit. I replaced the original 6.3v with a 25v instead of a 35v shown on the video which also works.

LCD repariert und Floppy Laufwerk, Sy77 Yamaha, tolles Gerät!

What do you use for cleaning the components?

do people talk anymore

least appropriate music

Thanks for this Video ! What Spray do you use for the channel fader? My Channel Fader makes noises when I move them. I think they are dirty. Do they need to be replaced or can I clean them and put some spray on them?

Nice video. Would this still work if there are some vertical lines missing on the LCD, or would that require an entirely new screen?

👍

Hola como estas ?? Para sacar las perrilas que llave utlizaste ???saluod cordiales desde Santiago de Chile 🇨🇱

do you provide this update servicing to other users ?

IMHO completely disassembling a pot as shown in the video is overkill and often results in creating more issues than you started with. If a pot can’t be fixed with a squirt of contact cleaner into a gap or hole while still in place, just buy a new pot. And always try this first, before you do anything else

I bought one of these for the Gameboy Color as well as recapped it and it is HELLA loud compared to what it was.

Maybe you can explain in short about upgrading capacitors on main output please. Bought capacitors by looking at our video but worried about screwing up :(

What kind of iron is that that takes away the solder automatically?