Thank you.

You missed to show the most important part the candy

Do you clear coat or put on a sealer after to keep it from scratching off. I've seen factory camo scratch off like a bad scab drives me nutz.

Wow! That looks so cool! Where can I get film?

Is that activator you dipped the brush in or water?

Well done y’all.. they look amazing!

How much do u charge for this service?

Here we go some guitar stuff this is what I'm learning dipping for, wish i would have seen this before my first shifted guitar mines basically just different colors in light vs dark

How big of a deal is water temp when dipping? what does the higher vs lower temps do to the reaction and process? I had a film dissolve when I hit it with the activator and I didn't think I had hydrated it for more than about a minute and I was thinking it was probably water that was too warm. Definitely wasn't fully activated either ;D

Wow! Channel Blocked: Liquid Concepts, LLC

5:15 honestly how's that even possible 😂

They look very nice

Perfect Explanation Thank You So Much! I Work With Epoxy Resin And I’ve Never Used A 2:1 Ratio Before. So This Helps Like You Wouldn’t Believe! And Seems Much Easier Now! Thanks Again! 🤝

Can i directlt hydrodip motorcycle fairings after sanding it? Coz it's black already. Or do i still need to repaint it black even it is already color black? Thanks. Im confused if repainting is really necessary

Can i directlt hydrodip motorcycle fairings after sanding it? Coz it's black already. Or do i still need to repaint it black even it is already color black? Thanks. Im confused if repainting is really necessary.

hi how are you i just want to say the dark blue works for me i would really like to buy it

I am more interesed in the sound genuine carbon fiber makes when you knock or tap on it, vs plastic...

This fender and tank look absolutely stunning 🤙🤙🤙

Hi I’m using your film and aerosol activator When I spray the activator on the film it sometimes all disappears before I can dip my item What am i doing wrong I’m not too close to the film when spraying and tape 2 sides and use dividers to keep film still Help please

It'd be great if we could see a video of you guys touchin' up carbon fiber , thnx

Can you guys do the barrel?

i am learning so much with your videos, thx so much

Thankyou for the information

Give me whatsp number brother

Do you clear over your base coat before dipping?

How long do you wait in between dipping each side?

How much does something like this cost?

We used the color shift on a test panel and dipped it in skulls to see what it would look like if we did the body of our drag car in it. It turned out ok, but think we needed another coat or two of the paint to make it show better

Lol. Your "not every customer is right" segment - you missed the customer that wants a job done cheap because he will send you more work, and then every one he sends you also wants the cheap deal - fast way to go broke.

Top!

What do you do about bolts or hardware do you dip to match

I’m looking into ordering a tank Thanks guys

tnx for the video brian i've been hydro dipping in middle east for sux years now today i found pictures of my old workshop .i started in a 15 square meter place now im at a 200 square meter workshop .there's still so much to be done but im happy with the progress

👍

Is this course available in india?

hi, i always follow you. at what pressure do you spray the activator? thanks you are great.

Need make some type of chart showing the wait time before and after spraying the activator with certain water temperatures and how it reacts

What if there is bleed threw from 1st dip and mixes with 2ed dip with base coat between

Those polycarbonate bodies require flex agents in the paint. If you would've used a few coats of florescent orange with a white backer that body would've really shown off the camo dip ..(remember you have to be able to see the car from a distance to drive it). Great process explanation!

what type of paint to use?

Oh shit thanks bro

hi,how to set gun

No hardner needed to be added?

I’m having issues with film rolling up and haven’t seen any vids to help. My film is curling up 2-3 inches on each side. Any tips? Have tried tape. But don’t want to do all sides.

👌 Can't you spray the objects and not the paint?

No dipping for me. I use paints. I use speed shapes to test my project idea's.

I was wondering what they were used for, thanks

Hello Brian I have seen your videos and they are excellent I wanted to know if this type of method is also suitable for silicone products that need to be flexible and stretchable

These are so handy, I buy a bunch and they help me learn how to dip for sure

Do you have more information on the hangers that you made for this peice? It looks like a peice of bent wire but is it also a spring? Do you sell them?