3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
4 жыл бұрын
4 жыл бұрын
5 жыл бұрын
5 жыл бұрын
5 жыл бұрын
5 жыл бұрын
5 жыл бұрын
Пікірлер
@masterscott555 2 күн бұрын
I just build the step 2 one! It is super! Next one will be this one:) kzbin.info/www/bejne/nKGpkIipqt1jjbssi=osDbhAkyv7z1hXA2
@masterscott555 2 күн бұрын
Yes I build it! Just super! kzbin.info/www/bejne/nKGpkIipqt1jjbssi=osDbhAkyv7z1hXA2
@user-zd6rf2qi1i 5 күн бұрын
Would it work if I make a buzzing relay to activate the earthing relay to make the spark cut happen
@gabrielv.4358 8 күн бұрын
So this is useful to make an carb engine not go kaboom when you are revving it? Coool! (I dont care about the pops and bangs lol) nice
@gordonredshaw5732 15 күн бұрын
Stick like shit to a blanket Stick like shit to a blanket Gold
@masterscott555 Ай бұрын
How is it going? Any news regarding the rev limiter?
@Marshall_Nero17 Ай бұрын
Your video is great..you should do more content about this..there are new rev limiter which were called Dragger Rev limiter
@walkertongdee Ай бұрын
Wrong title this video is about how to retard timing, I want to know how much to advance the timing by eye...
@acelpvz475 Ай бұрын
hi mate my quad has an CDI for the spark with a rev limit of 7500 RPM which i would like to limit to 5000rpm how would i do something like that?
@tytube93 Ай бұрын
I swear I could smell that 😂
@DemonTimeDocumentaries Ай бұрын
am I right in thinking: if you have a coil on spark vehicle (different to shown in video, each individual spark plug has its own coil pack) could you not just tap into the pos / neg and run those through the relay? im struggling more than i should be with this 🤣 also would a 4 pin relay work?
@sarmadahmed1029 2 ай бұрын
Where can i buy this ? Any website ?
@skullgaming7069 3 ай бұрын
Anyone on the comments ? Ive done it but not working ?
@skullgaming7069 3 ай бұрын
Anyone still on this comments ?
@MiguelSilva019 3 ай бұрын
Does anyone have the Aliexpress link for this relay?
@kspanda4582 3 ай бұрын
How to install. To injection engine
@bentonhomestead 3 ай бұрын
I checked out your videos because you subscribed to my channel. This was thoroughly entertaining, and I hope you didn't die 😂
@AaronBonBarron 3 ай бұрын
Thankfully I fully recovered from the food coma, but now I'm suddenly hungry at 10PM on a Sunday 😅
@viikp2k9 3 ай бұрын
Hey man nice work there! I would like to know if you have the gerber file for any chance? I would like to make this on a pcb
@triplsmusix2240 3 ай бұрын
Work on felicia 1.3 40kw ?
@jam58515 4 ай бұрын
I tryed this but every time i press the switch it blows a fuse, ive checked that ive got everything on the correct terminals, the relay is also brand new and theres no damaged wire, what can this mean?
@TheShadeTreeFixitMan 5 ай бұрын
Great demonstration.
@hollister5080 5 ай бұрын
I need answers I have don exactly like you showed but its not working like in the video any clue why? Ive been trying for days
@DAI.H4RD 5 ай бұрын
Worth asking... Whats the IC1P in the centre of the schematic next to C5. Looks like a short to ground with a parallel cap?
@EazYzZ1993 5 ай бұрын
Bru it's bobbing me, I have built this and can't seem to figure it out, if u watch video you see there is a brown wire soldered to a diode right by the irfz44n which God knows goes where nor on the schematic 😅
@DAI.H4RD 5 ай бұрын
@@EazYzZ1993 I'd Hazard a guess that its there to stop relay contact arcing from the pulses. Does yours work? I hear pin8 on the 4046 should be grounded too?
@EazYzZ1993 5 ай бұрын
IC1p is the actual IC power and ground wire, the 8vss and 16vdd is where those two wires connect on pin 8 and pin 16 on IC1 (4046)
@EazYzZ1993 5 ай бұрын
For In and S_GND you use a dual core wire, cut on wire short and the 2nd one you keep long and wrap around the High Voltage ignition coil wire, the wire you wrap goes on IN and S_GND is the 2nd wire that you cut short
@EazYzZ1993 5 ай бұрын
The OUT from the IRFZ44N goes to trigger the relay which you need to wire into the ignition coil
@waterfuel 5 ай бұрын
Can't the flywheel be tightened down with honing extra smooth of upper crankshaft and lock washer added, and used at different timing spot, by not using flywheel key? I heard others are doing this. Cars have adjustable distributor for changing timing. Large nut on flywheel tightened very hard. Briggs is pre-set at TDC.
@kostaspolychronopoulos3653 6 ай бұрын
Does this work on single cylinder engines?
@organicvids 6 ай бұрын
Would love to see you hook a timing light up to this. I am dealing with china starter upgrade to 2011 gx 390 and keyways are different.
@Somerandomkarter101-hd5yu 6 ай бұрын
Would this work on a 125 cc quad?
@cgplayground-yy6of 7 ай бұрын
can someone please tell what is the purpose of the vss and vdd connections and what can you do with them want to make this rev limiter myself and cant understand it
@Bestday413 7 ай бұрын
How much rpm
@achmatismail6585 8 ай бұрын
I have a koill puk
@achmatismail6585 8 ай бұрын
Hi cun I do this on a 1.3 toyota tazz
@S.DONKEY 8 ай бұрын
Dunno how i never found these vids until now How good "Too much boost made it headgasket'nt" 😭😭
@luiseduardomontilla8200 8 ай бұрын
buenos dia soy de venezuela sera que me puedes dar el diagrama de como conectarlo por favor
@maca2113 9 ай бұрын
Can you do this also with the motorcycle?
@myrthenboermann5979 9 ай бұрын
what is the brown wire for?
@myrthenboermann5979 9 ай бұрын
What should in do with IC1P on the scematics? It looks like i should wire positive and negative together but it doesnt seem right.. can anyone help me?
@DAI.H4RD 5 ай бұрын
Im wondering the same. Was thinking its a filter, 1Ps seem to be only surface mount anyways, video doesn't show the extra transistor, maybe just the cap to ground. also apparently pin8 on the 4046 should be grounded?
@louieTraina 10 ай бұрын
What size carb did you put on this motor?
@carsonrothwell_gaming1408 10 ай бұрын
How would you go about doing this on an hei coil?
@MichaelBellia 10 ай бұрын
How can I do it on my opel monza 2liter 😢 what do I need
@user-wu7vz4hm1i 10 ай бұрын
I need skema this video
@EtronicswithAleem 10 ай бұрын
I wanna make this & put in my bike
@kngzap928 11 ай бұрын
Anyone do honda civic D14 ??
@waterfuel 11 ай бұрын
Where is the large lock washer?
@bretjjjohnson7942 5 ай бұрын
Lock washers aren't used with the flywheel nut. The engine spines in a direction that's always tightening the nuts. It's the same reason lock washers aren't used with the lug nuts on your car. washers
@halyzaeyza8619 11 ай бұрын
Nice
@seavor-wq7lg 11 ай бұрын
fastest way to set your car on fire
@ItsPainnz Жыл бұрын
I thought it was better to turn the tilt back to about 8-10 degrees
@rischalennaidoo6477 Жыл бұрын
Pls show us how to do this on a toyota 2e tazz
@jheetman Жыл бұрын
May I steal your "stick like shit to a blanket" phrase for my own personal use?
@ralphvandriel4549 Жыл бұрын
Where does terminal 30 go