I hate these cv axel’s I never had one go in easy centering the clip on the inside part of the hub helps and turning the axel tell you feel it pop in also helps at least on a Honda, I’m so tired I don’t have the strength to pop back in the tie rod end back into place will do tomorrow morning wish me good luck 🍀

Well done!

Best video on this. Got it immediately after watching this 🙏

I love it. Such a brilliant idea. Thanks for sharing it.

You save my life thank you 🙏🏽

me and my brother have been trying for hours, then we watched your video, 30 seconds later it was in, thank you

Throw some loctite on those threads and that should help prevent the screw from backing out.

Spot on! I used this today and it was quick and easy to follow. Thank you!

Thanks for the vid man I just got it in after days of trying

Hi! Do you know what this part is called? Mine broke

Getting a hard times getting in too.ima try this❤

Damn, I just got mine in after a long struggle to get it OFF… The good news is that I didn’t have to tap it hard at all. THANK YOU!

Thank you , this video help me a lot , God bless you

Yo! Your video is a lifesaver. Thanks for the tips and all the best!

I'm betting my dishwasher that is a Kenmore is older then that one, I wanna know if it can be fixed if parts are available I live in Alberta Canada I cannot afford a new dishwasher or a big repair bill I'm hoping it's an easy fix that parts are still available even in 2024 so if anyone out there can help me great. My dishwasher turned on no problem then it was off no power at all, still some water in the bottom but it was only on for about 5 minutes not even so the water didn't have time to drain. I've been doing research and most videos are pointing to a fuse inside the dishwasher that is blown or a door switch whatever that is, all I want to know right now is even though my dishwasher is old probably older then the one in this video can it still be fixed? Ty

it says 76 MV not 76 Volts. also you need to switch the dial to the top red section that says DCV it is for batteries. all three multimeters were on the wrong settings.

Thx bro

I let the air out and then put the butane upside down and cover the fill hole, yet it always sprays all over me and I can't ever fill it. I always make sure to let the air out first, but I don't know what I'm doing wrong. Is there a good torch that you would recommend? Thank you in advance 😊

Thanks!

How about wen ur smoking and u only getb1 or 2 solid lights and then it acts as if it's dead a buddy showed me last summer how-to purge and he didn't do it anything like u did in this video and seemed way more effective he pressed the valve in but wen the air finished draining he flipped it holding the valve in and it continued to drain again hebdid that likeb3 or 4x but I still can't get mine to come out of limp mode or whatever it's prob is

I think I love you❤

Very helpful! Thank you!

I’ve Been trying for five hours came across your video. Boom. I just want to say thank you for your knowledge.

Perfect hack bro you saved me some mula $$ I was about to order a replacement part for $130 Thanks buddy

Bruh the way I grabbed my dried up torch that’s been marinating in my closet without fuel for months, released the pressure like you did and it works fine af 🔥 the way I never knew you had to take out pressure could’ve saved me from buying all the other ones that came after

Thats terrible u know how many mini torches i have ran thru because it kept squirting back at me when i tried to refill smh . Thank u

Do you have a video on how to change your daytime running lights my driver side daytime running light is out do I have to change the whole thing or can I change a bulb?

This was it! I was doing it on a 98 Cherokee with a solid axle so same thing except no boots so I had to use a hammer on the end. The reason it took me hours to finally get it in was because I was afraid of beating it too hard because it’s far from pleasant doing the axle seals if I was to have damaged them. I’ll see later on if I did or didn’t. It’s an exciting step towards getting her ready for an alignment (wheel hub and ball joints) and getting new tires. Right now she’s not highway worthy because it has a built in 50mph warning i.e death wobble.

Very helpful. Thank you!

just installed that same dish washer. Good to know for the future

I removed the shock but used big 2 lbs hammer that i used to sit front wheel bearings. I had my father in law tapping at the end while I keep it straight. It did went all the way in sit nicely against the transmission. I think you cam damage the bearing if you yank and hit it up like your method.

Thank u

Worked like a champ. Thank you.

Good evening my brother. The way to replace the headlight and turn signals is under the wheel well behind the front tire. If you turn your wheel to the left or right you will be able to see the access point to get to it. They mad it just for changing the headlight and turn signals. I hope this helps! No taking anything apart!

Thank you! Finally!

He dosent KNOW HOW TO USE THE totter

YOU ARE WRONG

Thank you for posting! I used this video to replace my bulb. Saved me $$$$$ doing it myself. ❤

Worked great , thank you

I fuckin love you buddy. Fuck every other video. Was so tired couldn’t get mine in lol. Then did your holding idea and boom

Can you still refill the torch without emptying pressure?

Wow I am so glad I found this video! Thanks so much for sharing this.. just wish I would have seen before I ordered a new cord lol

'promosm'

Honestly man you are literally my hero, spend 2 hours on my axle and with your method I got it in within 3 minutes🦾😂

Thanks was very helpful, thank you.

These Dodge cables are so thin on the inside. Super thanks! I'll note that if the ECM is giving 4.6 to 5V, then it's worth seeing if the ECM reacts well to the connection (i.e. a loop connectivity to the ECM is no possible). Short the two wires and it will read 190 degrees (i.e. P0112) or -40 degrees with an open circuit (i.e. P0113). I had to take the entire connector assembly a part as the wire broke at the connector end. I can make a video but I was very finicky.

Are you a mechanic?

Wondering how you get to know this. Did you read some manual or you learn it from a mechanic?

Does small vehicles have the same pipe with as that truck?

This is a truck, not easy to repair