This is like THE BEST advice for this bike. If you leave the governor on and the air filter on with no holes drilled into the cover then the bike will be sooooooooooo sluggish especially uphill or in grass with someone over 160

Should have adjusted for equal levels and done away with the compressor/limiter. The background noise is higher because the fake mic is hotter. If you dropped the levels on the fake that background noise would reduce significantly.

you should do a tear down.

I saw some acoustic panels, but your room is still way too "live". Shure needs to clamp down on these counterfeit goods.

Hmmm. Fake one doesn't sound too bad.

THANK YOUU!!!! My iMac 2017 27" 5K screen looks flawless again! It was easyer than I thought. I did not remove the tape on the cables. Only the tape that covered the screws. Then I used a lint free wipe and a drop of distilled water to clean the LCD panel and the diffusor. Then I removed the dust particles that got inside while I was working on it. I used a sticker that came with a screen protector for my phone. I cant't believe how perfect it turned out! It looks like new! Thank you once again!!

are you just lifting the engine? Or are you also pulling it out a bit as well?

Oh my goodness!!! thank you so much! I am pretty sure a candle contributed to mine doing this. oops

My Mega Moto 80, 98cc goes 35mph with the govenor still in place.

3:05 if you mess with the governor, your flywheel will blow up. Get an aluminum flywheel and get rid of the cast iron. The cast iron flywheel will blow up, destroying the engine and also could hurt you while riding.

Try a soup can it works mint then grab some pipe clamps

i made mine go up to 50. it was mostly my dad though

Finally, after watching countless KZbin videos where people do not explain this well at all, I find your video. Excellent, detailed information. Thank you.

RUN IT LEAN IT SOUNDS MEAN🔥🔥🔥

I didn't finish the video yet but most people don't address this. Make sure to tighten that throttle cable so ur take off and potentially top end is better. If u notice when ur stopped and try to use the throttle to take off, and it takes a lot of "twist" of ur throttle? It's bc there's too much slack in ur cable. I like to have it as soon as I even touch my throttle my bike is moving 👍🏽

I am 55 yrs old with a wild side yet but due to severe arthritis I bought my mini to replace running my service dog as I couldn't walk him no longer daily. Your vid was very clear, and educational and well appreciated for a little lady still living life full throttle.

How do you get it to turn off?

Fixed! All is well , nice and clean :) Highly recommend :)

Flip the exhaust for is isnt blowing exhaust against the wind. Common sense.

Would you know how to clean the air filter?

does it mess up the motor

I cut I little of my throttle spring and zip tied gov hit 30 and I’m 235

if the dust come into the screen, is it possible to vaccume this dust by a vaccume cleaner ? hope someone try this and tell us the right spot to vaccume it from ?

Wont that just blowup the engine lol

Thanks for the video! If anyone is trying to do this with the 5/8 shaft adapter sleeve. Put the sleeve on the shaft, then start the motor. The shaft will slowly turn, then just use some sand paper and sand till the pulley with the attachments fit.

Do urself a favor and get rid of the 🤣 crazy washer thing going on and make a rubber engine spacer I used old belt line and cut out vibration smooth even with the torque converter 🤠

Just ride it before and get the oil hot it will drain faster

😂 don't use washers ! Get a riser plate , it will be much more sturdy and safer.

Bought the exact same bike with a blown motor i swapped a predator 212 bought a MTR performance carburetor and a aftermarket exhaust sounds amazing I’ve done 52 mph on the highway on it

Can anyone tell me what part to use to unscrew the bolt he was talking about?.

He never installed the 3/4 cvt torque converter on the 5/8 shaft 😡 title should have been not installing!!

Can it be the 4 stroke 10-40 for a bike that hasn’t had the governor removed?

Successfully completed this project. Thank you so much for making this video it was extremely helpful. Converting my 27 inch 5K iMac to an external display. I had pretty large noticeable spots in the bottom two corners extending towards the middle - one of which was about 6 inches in length. These spots have always bothered me and have definitely been increasing in size over the last year. Very glad I came across this video while I had the screen off. Hoping they don't return with my display acting as an external monitor without fans. Best of luck to anyone else taking on this project!

Add a fuel filter! Are you stupid?

This is actually a really good trick I just need to get my bike running again

Good idea but too much air restriction. I still will should be more course and not as packed in the can. The air must flow, or your engine will be ruined.

Great communication and walk through narrative. Thanks for that

Compression determines what gas it uses efficiently

hi, I also fitted the same kit, when I walk 2 km I touch the belt and it overheats why?? yours is the same i.e. does it overheat??? or is it normal??

hi, I also fitted the same kit, when I walk 2 km I touch the belt and it overheats why?? yours is the same i.e. does it overheat??? or is it normal??

Thank you so much for making this video. I bought a 2017 4k iMac off of Craigslist with this exact issue, however it was top spec with 3.6ghz processor, 32GB RAM, 1TB SSD. I got it for only $250 due the dark spots issue. After, I found your video and was able to completely fix it. I feel like I got the deal of the century with these specs. Thanks again for taking the time to make this video. Btw I found you only really have to remove the tape on the bottom edge of the screen. On the sides, you can just cut the tape using your finger nail and it pulls apart easily when you lift it up

This is the what not to do video. My god.

Do you have an update on any more tips

I got one of these for 60 bucks from somebody that kind of looks now like a Indiana Jones bike but I actually took a small spring since it's already a lock washer at the chain tensioner and put it between the bracket and then the lock nut so now I have an auto tensioning one it works

mine is 13 years old and still doing great, i dont know what he"s talking about NOT lasting, there great little mini bikes

You need to put your tools away and never attempt this again. This was painful to watch all the butchery.

oh thank you sir very much, been googling a while to find the fix and here it is!

Oh man what a joke 8 washers 😂

Lol you cut your frame instead of buying the proper riser. Ay yi yi

Do you know what size chain I need for my 10t sprocket on my torque converter on my ct200u-ex