How to Get 35 MPH+ on Monster/Mega Moto 80cc Mini Bike

[@dianachambers4498]

Bought the exact same bike with a blown motor i swapped a predator 212 bought a MTR performance carburetor and a aftermarket exhaust sounds amazing I’ve done 52 mph on the highway on it

[@wendysmith5004]

I am 55 yrs old with a wild side yet but due to severe arthritis I bought my mini to replace running my service dog as I couldn't walk him no longer daily. Your vid was very clear, and educational and well appreciated for a little lady still living life full throttle.

[@isaiahmerida5475]

Around the left side of the carb on the bike, there is a carb adjustment screw which is behind a cap that can easily be popped off and be adjusted with a screwdriver to fix the lean running condition.

[@CarlosRivera-uw1ue]

Dude the thing with the screw helped so much holyyy! Thanks dude !

[@bmarquardt3242]

What do you use to move the screw??

[@212rodriguez1]

@@bmarquardt3242 You can't move with a small flathead screwdriver.

[@jamesrodriguez2200]

Did it make the bike go faster

[@SamuelMontalvo712]

I recently got a Motovox 79.5cc 4stroke for 250$ it runs perfectly brakes work everything is good i got around 23-26mph stock top speed, and i now got a straight pipe and gained 2-3mph, im watching this so i can get atleast 30-34 by taking off the speed limiter and the govnor to see if i can reach over 34mph this video helped me out so much, and by the way i raced a 212 predator, he got me at the start but i was starting to catch up thats insane idk how.

[@nnaheim.]

Make sure you change the voltage from 6v to 12v by flipping the voltage plate hidden under the tank as well.

[@jigwhatup]

Change the spring on the max torque clutch to make it slip higher. You’ll need to remove the clutch , remover the snap rings (remember or video how it goes back together) and then remove the spring. Install a stronger spring to make it slip higher. The clutch springs are less then $10.

[@fasterthunder8308]

I didn't finish the video yet but most people don't address this. Make sure to tighten that throttle cable so ur take off and potentially top end is better. If u notice when ur stopped and try to use the throttle to take off, and it takes a lot of "twist" of ur throttle? It's bc there's too much slack in ur cable. I like to have it as soon as I even touch my throttle my bike is moving 👍🏽

[@bigdv519]

Hit 32.5mph today in mine. Screw mod and a rod between the 2 levers. Previous max speed was 25.8. Next mods will be intake and custom exhaust.

[@Denzel9911]

Is it still working up until now?

[@bigdv519]

@@Denzel9911 yes still working. Needs a tube for the rear tire.

[@tokin420nchokin]

What is the screw mod?

[@tokin420nchokin]

Also what 2 levers are you refering to?

[@canheaton]

Thanks for the video! By looking at mine i noticed also that the throttle cable was not even tight enough for the engine to get to full throttle, so i tightened that and unscrewed that limiter scew ( you dont have to take it all the way out, just enough so the moving parts dont hit it) and now my bike is waaaay faster. I dont think i would want it any faster. Lol 🎉

[@Ray09666]

Hi what part did you use to unscrew the bolt?

[@blazingchris]

I just got mine as a gift and 2 days later a crash it into a old tractor didn't do anything to it but take some of the plastic off it was fun

[@armanimoore5541]

Awesome! Hope your okay

[@wendysmith5004]

I also hope u r fine. Sadly...😮 I LMAO!!! Ty for the honesty and your story. You lived to tell your tale!

[@Slicknewt]

I got a used motovox one of these, same 80cc motor for $220. Thing has sluggish acceleration but impressive top end speed for an 80

[@Professional_hooligan]

Change your sprockets

[@TeoVVS]

damn you got scammed you can get a used one fore like 50-80

[@undagroundhustla]

@@TeoVVS you wish buddy, not with all this Bidenflation. 💰💰💰 You ain't gonna find one complete and running for less than $200 and if you do happen to find one on the cheap you are extremely lucky.

[@hayimhere9604]

These engines last a long time

[@iceagebaby1993]

hay I'm here, yeah I bought mine 4 years ago on a crappy garage sale and I repaired and recently started using it, it’s a beast

[@andrewwarner1239]

facts mines bee running for 7 years strong

[@taylornyholm5878]

Not new coleman engines. I got my bt200x and it already has problems.

[@isaiahmerida5475]

Mine is a 2014 model. With regular maintenance, its still going strong!

[@taylornyholm5878]

@@isaiahmerida5475 yeah the older models are better and i was too late to get the reliable

[@derickthompson8669]

I want mine to do about 40-45mph and my bike i took off the air box off and zip tied the filter in. I replaced my throttle spring i never thought about the little piece of metal for the governor. Good information

[@jimmyboy278]

Dude the christmas ornament metal really works dosnt dropoff any more foes full throttle foreever and the air box hole made mine run so smooth qnd fot it over 35 mph great vid

[@voithy8351]

The problem I’m having is my throttle works but doesn’t accelerate it. I’ve tightened it and messed with it but from what I can tell is it’s my rpm limiter aka that long metal rod going up to the carburetor. It stays wide open.

[@Naferner_Said]

Compression determines what gas it uses efficiently

[@fasterthunder8308]

RUN IT LEAN IT SOUNDS MEAN🔥🔥🔥

[@forfashire]

got mine to 31 and i didn’t even touch the airbox yet 😎

[@forfashire]

update: drilled some holes in the airbox and it did nothing. just looks uglier and is prone to getting dirt and water in the airbox and making your filter dirtier faster. DON’T DO IT, WORTHLESS MOD

[@asamercurio7988]

@@forfashire patch it up with flex tape then seal

[@Jj-sk8.s]

I did 35 with mine

[@nollidelddik]

Mine does 51mph

[@forfashire]

@@nollidelddik that’s pretty cool! i have a stage 1 212 on mine now and it goes around 40 or 50

[@roynelson7613]

Had a friend stop by today with one of these said it does about 40 miles an hour I think it feels that fast to her but I knew how to do all this but this was a great video and awesome video especially about the governor a lot of people don't know that happy holidays Merry Christmas my friend 👍🏽💪🏽👊🏾💥💨💨💯🎩

[@lukedeguiseppe5790]

For anyone watching this, that big lever does not control the governor. I have fixed one of these bikes up and inside the crankcase there is a plastic gear, that is the governor. If you wish to gain a lot more top speed other than putting an unreliable paper clip on the carburetor lever is to drain the oil and remove that screw. That lever he says that is the governor is the carburetor lever, so when you pull the throttle that lever punches the carburetor door open allowing the fuel mixture into the engine. Please do not drill out the carburetor holes, this bike is a 1 cylinder and only air cooled, so if you are putting to much into it you make blow the engine up on a warm day. If you would like to do real modifications and not hurt the engine, you might want to look into getting a higher displacement bike. I left this comment here so that some kid watching this can’t get hurt and won’t get his dreams crushed when his mini bike has a hole in the piston. I don’t mea to diss Ty’s Tech but this is rather unethical. This bike also may not have correct tires on there to attain this type of speed. It also may not be set up to go this speed such as the crankshaft, camshaft, the bearings, the chain, and the wheels themselves. So please if you are looking to get more speed out of your bike you may have to do some shopping to keep it safe at all times. Such as purchasing some street tires to go on the street, perhaps buying a predator 212cc, maybe some higher rated bearings and a thicker chain. Also don’t mess with the brakes unless you know what your doing. Stay safe!

[@xXB.FunkXx]

One of the best ways to learn about engine's is trying to make one faster, blow it up then really make it faster.

[@littlebreadstick3505]

I know this is a bit late but could you make a video on this thanks

[@Erik0824]

Update: I just got a predetor 212

[@aronncalabrese3576]

Erik A good looks man

[@whiteboysteve4474]

I got a kx100 2 stroke on mine I also have 10" rims off a mini ninja looking bike

[@dauntlessentertainment4922]

It's been a year, hows it running? What's the top speed?

[@Erik0824]

@@dauntlessentertainment4922 it was running great, I live in Minnesota so I can’t really ride right now because of snow. But it was reaching like the 40mph range. And it still runs like I bought it yesterday. I’m definitely getting some kits to make it go faster next summer.

[@dauntlessentertainment4922]

@@Erik0824 That's great to hear! Did you do any mods like govenor removal or just leave it stock? (Sorry if I asking to much, I'm new to 212's and mini bikes)

[@cj3883]

Very much appreciated man!

[@sivphuingan5506]

I still dont understand how does adding the green wire makes the bike go any faster. There's already an existing wire there so why does adding the green wire make any difference? I read this entire thread and i'm stilllost. I tried added the addtional wire and gave the bike throttle and everything seems to be moving the same.

[@robspear03]

Thats not a wire, its a spring. The wire this dude added bypasses that return spring.

[@angelmedina6390]

@Sivphui ngan my bike does the same as you describe yours does. When the bike is off, the governor arm moves with the spring that's already there when I give it throttle. Tomorrow morning when ib turn it on & maybe there is a difference when it's on or off.

[@Blessedup69]

Why is it in your kitchen?

[@HP.Customs]

During the winter I keep my Yamaha V-Max in my spare bedroom.

[@MP-zh2tk]

Dude super funny!!!

[@trentonfisher9252]

why not!!?

[@shancyroesner9212]

Mine did 37mph on 91 octane and only about 32 on 87 octane but the fuel economy is better and the engine runs cooler

[@Ponlets]

imagine it on hydrogen lol

[@matthewarnspiger632]

I got mine up to about 39 on 93 octane, ofc I also removed the internal governor

[@markcollins5026]

Man, mine did 84 mph with no octane !

[@bikeswithjuan5541]

@@markcollins5026 no it didnt stop lying

[@bradyhodge3190]

Was your muffler turned around so it points the back of the bike instead of the front?

[@braxton2007]

probably

[@davidpayne4084]

I bought one of these for my son when I bought a Baja 200 warrior I had a stage 4 predator I built and put on the Baja took 196 put it on the moto 80 sold the motor to my neighbor for a tiller he was working on

[@rylancollins8858]

mine is 13 years old and still doing great, i dont know what he"s talking about NOT lasting, there great little mini bikes

[@LordWolfman1119]

I got one of these for 60 bucks from somebody that kind of looks now like a Indiana Jones bike but I actually took a small spring since it's already a lock washer at the chain tensioner and put it between the bracket and then the lock nut so now I have an auto tensioning one it works

[@aronfried7737]

I did all of the mods in this video. I topped 35 MPH. However, the engine fell apart and broke internally as I believe it couldn't handle all the pressure. I now need to get a new engine.

[@undagroundhustla]

212 cc Predator. $119 BEAST

[@TeoVVS]

lmfao

[@romancedennis290]

​@@undagroundhustla would it fit

[@undagroundhustla]

@@romancedennis290 it will if you modify the air box and exhaust, or just go aftermarket with both

[@romancedennis290]

@@undagroundhustla I got mb100 massimo mini bike u think a 212 would fit on there

[@lifesgiftbychaunta6045]

Hello how r u? I have a realtree 100 min bike is there anything I can do to make it go faster without removing the governor. I would be intrigued to know this is my frist min bike. I'm learning

[@yungst1xk745]

can you still buy moster moto in 2020 nov in walmart

[@Captainkleen]

I have to correct you on the Governor internally the the gear has weights and when the engine rpm exceeds it’s limits the Governor arm kicks the weights open causing the engine to slow down. Pulling open the throttle all the way without the engine running doesn’t effect the Governor. I have a tip remove the Governor by opening the case and taking a punch to the gear on backside and pull out gear arm and washers. Many people open them up and screw around trying to get the c-clip off when you can use a punch and the arm will slide out without cutting it. Yes I’ve worked on many engines and still do.

[@yeshfhrhehdfhffgfhf4408]

Ur selling it on offer up right

[@Blessedup69]

Yeshfhrhe Hdfhffgfhf lol

[@bumblebee7663]

My engine starts but when I go up a hill it cuts off then when crank it up and drive it only needs a straight road it only stays on for 5 seconds then shuts off. I haven’t change the oil ever since I got it in 2016

[@bxballa17]

Take off your oil sensor... Clip yellow n black wire then remove

[@bumblebee7663]

@@bxballa17. Thanks

[@oOb2KnErOo]

Dude that screw + Premium Fuel mod is LOVELY

[@TradingWithJoker]

Title:How to blow you're engine up

[@n0texo578]

VikzFN nope my mini bike is still goin strong 45mph 💪

[@niahrobinson350]

TasteySnail howwww

[@junt6205]

Bludzy it doesnt blow the engine those bikes have settings to go fast

[@austinhenares1971]

Now mine runs at almost 30 thanks 🤙

[@johnpopzgrace1900]

Where did you get the chain tensioner roller from? I'd like to get one too! Please let me know! Thanks

[@Steadyglok]

eBay or Amazon most likely

[@lazardboi1890]

Inside of the muffler there is a screen you can take it out it is super restrictive!!

[@hotwheelsracer6380]

Yes, I have a mm105 and I didn't like the speed of it so I took a pair of needle-nose pliers since there's two spot welds holding the spark arrestor in, I just grabbed it with needle-nose pliers and stab the hole in it and ripped it out in pieces and it made my engine a lot louder and faster

[@1jpernice]

Hello, thank you for doing ur video, it was very helpful. I have the electric version of this mini bike. Can I make the same modifications with the taking out the screw and the spring. Lmk thanks

[@zoticluvsyou3591]

did this n went from 21mph to 28mph but there is popping

[@sat_sonic]

Great video and explanation!

[@unclegrandpa6384]

Would you know how to clean the air filter?

[@ememnezzy9916]

Bro, thank you so much!

[@justinwoods240]

It does not even go 35 mph at all cars and cameras moved theirs to the max and only went 28 mph

[@Grey_Beard72]

I can't speak for the 80cc but I have the 105 and it did 29 out of the box. They are only supposed to do 24 but I'm thinking the governor wasn't engaging all the way or something. I bypassed the governor and it now goes 35. Usually when you bypass the governor, it will increase by around 13 mph but it was already doing 5mph more than it was supposed to be doing and I weight around 210lbs. I'm going to do some more mods like carb and exhaust.

[@jimmyboy278]

NoahAndino same bro

[@jimmyboy278]

There heavy and the engine was brand new not broken in

[@jimmyboy278]

Candc

[@unknown-jd2tr]

caaaap i mine got 28 stock did the mod and it now does 36mph

[@samnigro1138]

Will it run with race gas

[@Erik0824]

Yea that’s what I use. If your talking about premium.

[@samnigro1138]

Good to know thanks

[@bryanmartin1975]

I run VP 110 😂😂

[@Iowa599]

"that screw" (on the governor) is also to prevent strain on the carburator by limiting travel of the linkage. Also, it throttle plate can over travel, over travel is actually closing the throttle. Higher octane gas is actually lower power, but a higher octane prevents preignition, and these tiny "industrial" engines don't have any preignition concerns.

[@MegaDysart]

Higher octane isn't "lower power" it's just more stable under high cylinder temps and resists pre ignition or knock. Any engine can suffer from preignition and if you've modified the governor on a small engine to increase the redline then you will have a higher dynamic compression ratio, more advanced timing and higher cylinder temperatures which could definitely justify higher octane fuel. It's all trial and error but making blanket statements like that don't help anyone.

[@Iowa599]

@@MegaDysart lol, you're very dumb. "The other rarely-discussed reality with high-octane fuels associated with "high performance" is that as octane increases, the specific gravity and energy content of the fuel per unit of weight are reduced." en.wikipedia.org/wiki/Octane_rating#Effects_of_octane_rating And you are not revving a mower engine fast enough to effect "dynamic compression"! Hahahahaha!!! Where the hell did you read that? The faster an engine revs the less air it can suck in because of the intake restrictions. That means a mower engine has the highest "dynamic compression" when you pull the starting rope, since the governor is holding the throttle wide open. You're just inventing reasons to justify putting 93 in your go kart!

[@jamarihickmon7795]

I like your dog

[@chadwilliams2973]

Lol i like the dog he is cool

[@LvSway]

Lol

[@Ray09666]

Can anyone tell me what part to use to unscrew the bolt he was talking about?.

[@lifesgiftbychaunta6045]

Another question I have for u is how do u tighten the chain I can understand ur videos. Plz get back to me have a Blessed day, ty

[@cryptotobias7860]

There is a rubber tensioner on the bottom side of the chain. Just loosen the bigger 10mm bolt and then tighten the smaller 10mm to tighten the chain by pulling the tensioner closer to the rear tire , thus resulting in a tighter chain. Then tighten to bigger 10mm to lock it in place.

[@kalebdoak1488]

Thanks I really needed this.

[@timothyroskie5742]

Could you put a KT 196 York converter on it???

[@lazaroperez8733]

thank bro know i can race with my friend he has gocart that goes 30mph

[@TLMOA_s_playground]

My air filter was drenched in oil

[@dwaynebowman2175]

Do you have an update on any more tips

[@_.calexb6435]

On mine I just put a sock with a hair tie over the intake cus when we bought it it didn't have a filter or cover

[@williambeckham3447]

Does it run okay? Mine fell of and can’t find a new one

[@Erik0824]

When I pull my throttle on my bars I can still push the actual metal throttle further

[@TysTech]

You need to tighten up your throttle cable a bit then.

[@GfoeGfoe]

@@TysTech i have a the same bike i just got a smaller sprocket which is a 36 tooth and 41 chain and a new clutch im doing 50 with a lil work done to the motor im doing a good 50-53

[@newgeneration1540]

@@GfoeGfoe how...

[@tornadoidk1469]

Ty's Tech then the idle will become too high and will pull on the clutch ( my dad did it and the bike started rolling and also it can lock up and the throttle won’t stop)

[@yeboidustin8725]

@@newgeneration1540 he has a small ass back sprocket but the down side to that is that it takes him 10 minutes just sitting there at full throttle to reach those speeds

[@coltencarroll1029]

Idk if anyone will see this but that spring on mine is broken and all it does is idle now

[@naturebeast2647]

I’m confused on the mod where you tie the Christmas thingy to the governor

[@jimmyboy278]

The governor outdoes the spring and makes it drop throttle from the carb to the engine so it dosnt go to higher rpm but if u put a solid piece of metal itll stay full throttle forever and get to higher rpm and outdoes the govenor

[@naturebeast2647]

Jimmy Boy I just added it and hit 34 mph!

[@prexy4939]

So if I were to upgrade the engine to a Predator 212 would I have to remove the paper clip or leave it.

[@TT4ME]

If you upgrade to a predator none of this applies. I'm in the process of changing mine. Already pulled the governor out of the engine. Waiting on mounting plate and smaller rear sprocket because it will pull the front wheel up instantly.

[@fatboy7503]

I got one got me a redneck custom exhaust with a metal broom handle but my little monster moto runs 31 and if I get lucky 32 33

[@desertdog01]

Where Do you order one sir???

[@hitman.773x6]

Will these messed up your engine

[@taeko4474]

did u flip the exhaust?

[@brakortiz5640]

hi should i get a monster moto 80cc for 100 ?

[@reaper5498]

Do you know where to find that exact engine on it

[@Shark_Theory]

I think that's the stock one

[@furiouslightning1371]

Do you drive that on the street

[@aydenchristian9131]

Don't do this unless u plan on getting a new engine because it fried my rings and exploded my governer which the schrapnel destroyed everything else just make it simple and get a 212

[@deshawnp617]

Will it explode your governor if u did the screw thing

[@fordlover4602]

@@deshawnp617 no just leave the governor alone unless you are going to completely take it out

[@tornadoidk1469]

Deshawn Parker no, but the engine may get hot

[@sayblaze]

My son moto bike won't start it cut off I changed the spark plug clutch every thing I even spray starter fluid on it made it start drove it up the street cut off again

[@2xx768]

I took off my screw and did what you said and it’s still the same!!! HELP

[@Leebear22gaming]

Can I buy those plastics from you

[@ninoreeves7702]

i was hoping for a ride. good info!!!!!

[@seangreen3500]

It’s not leeever it’s lever

[@acingpitch0760]

I just got this mini bike for my birthday but it was used and the owners never really told me what oil it used any suggestions?

[@get.sykedgaming7124]

10w 30

[@lancairw867]

Yes 10w 30 or 40. About 15-16 ounces. About half a quart

[@darrinbarnard6797]

How much was that bike

[@Yyodajedimaster]

That screw was welded in for me

[@skii9333]

So why does the video say 35+

[@Ponlets]

is it 4 stroke or 2 stroke

[@spitgritandducttape6891]

4

[@charlisperez8581]

can you install a torque converter on that motor?

[@ritz2546]

No, they don’t make em for 5/8” crankshafts, that’s why I’m on this video lmao

[@karlwithak6276]

Mine goes 40mph stock I just push the rod back connected to the carb

[@user-vu7xu9dp2l]

does it mess up the motor

[@NoahTheMann]

It works

[@MultiPoopoo101]

how to blow up your motor

[@braxton2007]

nope i have had mine for 5 years and i did this and still going strong

[@jimmywhitlow7174]

It still takes off very slow. Instead of spending a couple hundred bucks to make it fun, just buy a 6.5 Predator. It will do around 50mph with it stock and you will only have around $200 in the upgrade. ( motor, clutch, and chain.)

[@jimmyboy278]

True acceleration sucks i have to kick off but it mine foes 36 and it barely wastes gas

[@dominiclaker5675]

Flip the exhaust for is isnt blowing exhaust against the wind. Common sense.

[@buckhunter8576]

Im thinkin bout buyin one...its on sale...124...was bout 400

[@TysTech]

Wow, $124 is an absolute steal for one of these! I paid $349.

[@TT4ME]

I paid $50 for mine in mint condition. The old guy had no clue what it was worth. Installing a predator 212. Got the bike all gutted and governor gear has been removed on the 212cc. Just waiting on the mounting plate and smaller rear sprocket.

[@jimmyboy278]

TT was it easy putting the predator

[@LvSway]

@@TysTech I paid 407 for 100cc plus taxes

[@jdwayne2441]

Aftermarket carb, no air filter governor delete im pushing 45mph

[@thetimedoctor8542]

How much do u weigh bc i want to buy one im 5,7 and and iam 175lbs

[@nnaheim.]

Fatty

[@notskeppy638]

I also bypassed the governor on top of all if this and my clutch flew off the bike

[@chrismorgan1366]

It just wasn’t tight put blue locktight on the clutch bolt

[@notskeppy638]

@@chrismorgan1366 I know got it fixed. Dont know what i was thinking

[@ZenthHasGame]

i put a 212cc predator engine in mine with a aftermarket airfilter, exhaust, and took govenor off i can go 71mph on it abt to put a mini turbo on it😈

[@justinwoods240]

They don't go 35 it goes 28 after modding I have plenty of bikes to know that with plenty of more with a bunch of mods it still went 30

[@jimmyboy278]

Mine went 36 so maybe yours isnt broken in or that you didmt put that metal so it sosnt drop off

[@bmarquardt3242]

What do you use to move the screw??

[@williambeckham3447]

A strange thing called a screw driver

[@julianbloedow9164]

@@williambeckham3447 that’s a super rare tool

[@danielandrassy407]

Why is ur muffler upside-down

[@braxton2007]

he flipped it so it was not facing forward

[@monotheis6889]

mine sed off road use only. ha! gotta Fred Flintstone it from a start on flat hard ground. built transmission and now it goes up hills with 225# ass on it. only goes 18mph, but off road is great.

[@larryjohnson8549]

The octane has almost no different in speed unless running alcohol

[@bigred2217]

Everyone saying it goes faster is cap the govonor has a speed limit

[@jodyholcomb3738]

I had one one time an had no breaks on it an it tore my shoe bottoms apart I ride it with no breaks it was fasts an I'm. 270 an mine pulled me with 3 HP it was fun

[@thesmashes6758]

Thx dude I can go a little bit faster thx I'll let subscribe

[@dover1966]

Wont that just blowup the engine lol