Hi there, if you mean the cistern its Tradelinks homebrand but I wouldn't recommend them anymore. Reece base cistern is to me a better product for a budget cistern
@GanilOnesell15 күн бұрын
Please make new videos
@GanilOnesell16 күн бұрын
Do you run the drill clockwise mate?
@ezyfixplumbing955216 күн бұрын
Yer mate just as if you are drilling a hole with a drill bit
@torijarrett409818 күн бұрын
Could someone tell me or give me a link to where to buy the pan seal that he had to flip? I need one asap
@Martinidog29 күн бұрын
You just saved me a few hundred bucks. Thank you!
@wheres_bears1378Ай бұрын
Probably a silly question but if drilling into the wall to fasten the cistern is there a chance of hitting pipes or are the pipes usually located lower? Just wanted to double check before I have a go
@jasmoore5716Ай бұрын
Hey mate, no I've not come across it before but hey always a 1st for everything. Just make sure you screw into a stud if possible regardless if it doesn't line up with the holes in the cistern just make a new one. 1 good screw into a stud is better than 2 screwed into gyprock or cemet sheeting.
@wheres_bears1378Ай бұрын
@@jasmoore5716 perfect 👌 thanks mate you’re a legend 👍
@lucienleon84392 ай бұрын
brilliant 'how to' - low on production quality but high on easy-to-follow clear explanation. This was the video that gave me the confidence to give it a go after months of putting it off. No my dripping taps, thanks a million :)
@ethanwasme43073 ай бұрын
can i move from new zealand to come do an apprenticeship with you :'(
@dickon7283 ай бұрын
Good video
@LoneWolf-sh1ph3 ай бұрын
What if i have water leaking out of the tap handle when i use the hot water?? Any clues?? It leaks when in use and my back wall is all wet, been like that for over a year, plumbers are useless and cost me a fortune with no fixed results. 😡
@jasmoore57163 ай бұрын
If that is the case you will need to service the spindles and install new orings and/or could also mean the spindle is over reached and due to the breach seat being thin. Without seeing it very hard for to tell which it is sorry
@LoneWolf-sh1ph3 ай бұрын
@jasmoore5716 im born in Australia, and I'm 51 years old . What I just read sounds like another language 😂 . Thanks for helping I will look into it. Cheers 👍
@jasmoore57163 ай бұрын
Hi mate, no not if you have the mains off
@paulmorrison63803 ай бұрын
Hi great tutorial do i need to turn of or isolate my hot water system to do this?
@Andy-so9wt4 ай бұрын
Champion. Thank you 👍🏼
@leakena8895 ай бұрын
OMG thank you so much for your tutorial. I think I need to clean the seat so I’ll need to get that drill bit. I have change the washer like 5-6 times and I have to really turn the tap so tight to even have no water leaking from the shower head.
@andyufcfan13775 ай бұрын
2 hours trying to get mine to stop and couldn't do it. turn the tap on and water comes out under the handle from the wall. Gave up. Maybe it was a bad piece of rubber or something.
@julia.rhiannon5 ай бұрын
I bought both 50mm and 40mm pan cones just in case. Turned out I did need the 40mm one! Easy and clear instructions, and video. I had to use a little bit of detergent but got it fitted in 10mins for $5 Thanks, you're a legend mate. Liked and subscribed.
@wizdude5 ай бұрын
Mate. You’re a dead set legend. Has to change one of these tonight and couldn’t work out how to get it on the back of the toilet. Fold it back. Legendary move. Thanks for the awesome video. Cheers!
@geoffrandwick50205 ай бұрын
Nice 👍
@plumberski88546 ай бұрын
Just the video I am looking for. Many thanks for the ingenious way to insert the 2nd cone!
@razarriot6 ай бұрын
Awesome, excellent video. didnt think that cone rubber wound ever fit . you made my life easy. thanks mate
@bbking00646 ай бұрын
With these Caroma toilets with a lever mechanism (the same as in your video), how do you remove the outlet flush valve to replace the seating seal?
@bodhi94646 ай бұрын
Thanks mate. 🇦🇺🙏🏼
@anthonyholland26057 ай бұрын
Use a waterless tap next time. Much better than the washer taps and never leak.
@craigjones69637 ай бұрын
Thanks mate
@markjohns43677 ай бұрын
Thanks mate
@abrogard1427 ай бұрын
the o rings don't stop it dripping do they? just stop it leaking to the outside when the tap is open, water coming out? and how far down can you take the tap seat? I have one with a black line across it which I suppose is a groove and that's where the endless dripping is from. but i've gone down what seems like a long way to me and it is still there. Must be a thing that happens a bit. so how far down can we go? and i'm thinking now get a push in reseat. so what about them? good vid. good clues. add those extras: great.
@ezyfixplumbing95527 ай бұрын
How far you can reseat is a difficult question to answer mate. Is it in the wall like a shower breach or on a basin where you can replace it with ease. Sometimes if the cut on the seat is deep you might have to tap in a new seat instead of facing the one that is there. Sorry I can't give you a more direct answer without seeing and being there
@abrogard1427 ай бұрын
@@ezyfixplumbing9552 hey, hi... thanks for that. I'll take a punt on one of these 'tap in' replacement seats and then if that doesn't work I'll go for the hydroseal 'screw in' job. I'll try and measure how much depth of seat there is left somehow. I wondered if this 'squiggly black thread' across the seat, from inside to outside, was a known happening and if so what is it? cracked brass casting? they are cast are they? or fault in the casting? you get that, do you? or there's some magic bug that eats through? I'll believe anything. :)
@jamescollins69277 ай бұрын
Worth you wieght in kee seals thank mate you are a legend
@intestinalworm12027 ай бұрын
That's great - thanks! Now, bloke at the hardware store said plumbers reckon the white rubber pan cones last longer than the black ones (black ones tend to perish quicker)?
@LostWhits7 ай бұрын
Ever have the tap washer expand so much you need pliers to get it out?
@ezyfixplumbing95527 ай бұрын
Hi mate, yes many a time I've had that happen. Just need small screw driver, pointy nose pliers and a torch.
@LostWhits7 ай бұрын
@@ezyfixplumbing9552 I just had six of them. I just broke off the rubber and wiggled it until it gave.
@jaciobe8 ай бұрын
Awesome thanks! For a bath tap where would I turn the water off?
@ezyfixplumbing95528 ай бұрын
Hi mate you will turn the water off at the mains where your water meter is
@Aeslyth8 ай бұрын
Piece of piss. Great vid thanks
@xd-ke8yk8 ай бұрын
This video was perfect, thank you!
@cakeman84068 ай бұрын
Can you please make this not age restricted
@ezyfixplumbing95528 ай бұрын
Hi there yer sure
@LordByronMacintosh9 ай бұрын
great thank you, very helpful
@marcusher49799 ай бұрын
Thanks so much, well explained. This video will probably be popular as long as toilets work this way!!! 😜🚽🌊
@wogbhudd9 ай бұрын
Legend
@chantelleleplatrier94789 ай бұрын
As soon as you said it's a waste of time reseating I dropped my phone went to Bunnings and grabbed a new tape and some tape for $16 bucks and omg you were right. Problem solved let's move on with our lives. Thanks for the vid! :)
@nornicle29 ай бұрын
Saved me $600 in plumbing call out fees thanks boss
@vin17flores729 ай бұрын
Your explanation and communication was on point. Well done. I enjoyed viewing it.
@kijo10129 ай бұрын
Great video, cheers !
@dave29969 ай бұрын
Hi there im using the exact same resetting tool from bunnings and i have been screwing down the tool thread bit into the red fibre o ring before spinning the drill bit. I notice you dont bother with this step and you get a perfectly smooth face. Is this why my tap is still leaking after resettling?
@ezyfixplumbing95529 ай бұрын
Hi mate, no I don't think using a fiber washer on the tool will make any difference. If it's still leaking it must have a small imperfection on the seat or you've gone too far on the seat and now the breach may need replacing as if you've gone to far it will be to thing to install a new stainless steel seat
@dave29969 ай бұрын
@@ezyfixplumbing9552 thanks ...dont want to go down that path.
@johnbassett54079 ай бұрын
Classic...thanks for sharing.
@johnbassett54079 ай бұрын
Hope your Christmas was good also...😀
@BenryDess9 ай бұрын
As soon as I heard your accent I knew this would be no bullshit.
@matthewroberts51469 ай бұрын
Awesome video - thanks so much, I replaced the cone type pan seal in about 2 minutes using this method. No lube required!
@jenrich11110 ай бұрын
Great advice having taps open - but you did not address, nor replace, the red washer, between the tap and the wall pipe!!! That should have been checked for leaks after you turned the water back on. Be careful not to damage thread.
@nopoint242710 ай бұрын
Thank you you saved us $100+ on calling a plumber to do it for us.
@mehdiasgharzadeh516210 ай бұрын
thanks mate
@anthonycrossley242610 ай бұрын
Is there a better option than those terrible thin Metal Tubes used to loosen and tighten the Spindle Nut ?. I do have deep Sockets for Car work..however they may not be deep enough...